SJ McCarthy, our contract is stated we are responsible for the materials and we pay for the labor. Unfortunately we never met nor discuss with the owner but only discussed in details ( in the proposal) with the project manager who is the solely the carpenter.) We just found out there were a lot of the DETAILS from the proposal were not explained (per the PM,but who knows) in detail to the owner or almost like "bait and switch" - for example like item #2- he spent more time because the owner did not get him another helper to help him- I told him this should not be the customer's expenses-Anyway we are willing to pay for it. The owner was offering to renew and establish a new contract from the original contact ( we felt that he cherry picking the items from the proposal, we marked them up then again he decided not to included) for the unfinished works . Once he agreed in our 2nd meeting (another example: he agreed tiling our study room to be included from the original contact in our 1st meeting then when he write the REVISED CONTRACT- he wants to charge us ), but again we are facing the same old stories-he tried to change the wording. We were burned so many times and now we diligently review line by line knowing the owner's personality. He kept saying he lived by the contract-then I told him then he should honor the low estimated to install our engineering hardwood floor including removing the carpet-in the end he says he would honor but he did not including the cost in the new REVISED contract which we add into it - we are so tired with his games. So now we put a contingency - once we agree with the new contract, no more additional expenses from the previous work was done- and we do agree that we need to be notified first and need both signatures for additional expenses from the new contract. and no more point finger of "not included" since we have discussed in detailed and are in the contract. The new addition has a hardwood floor installed - with Dri-core. Once hardwood floor was installed- they are some areas squeak- we were told by PM -put a marked up then he would fasten without explaining to us-these would be additional ridiculous charges (PM told the owner, too-we told PM that they should explain it to us- ) Regarding the installing the engineering hardwood floor is for our existing rooms(concrete slabs that has plywood already)- we are told just to put a vapour barrier. Is it possible to let me know what brands for the glues have to be moisture resistant ($2/sf) or moisture PROOF ($3/sf).? The manufacture instruction suggests to use Franklin Tongue and Groove adhesive (cross linking polyaliphactic emulsion glue) www.titebond.com -any suggestions? This Applachian engineering hardwood floor - FLOATING only needs GLUE between the wood (tongue and groove per the manufacture manual ) then would be FLOAT - this is not to be GLUE DOWN on our concrete floor (could be glue down if necessary but not in our case). Here is the website- on PAGE 9 http://www.appalachianflooring.com/uploads/general/documents/engineered-installation-guide.pdf We trust the PM and we pay for it- we just want to move on and complete the project-It has been almost 10 months. We have to do what we have to do to protect ourselves now- The owner refuses to install our towel bar in our new shower without charging us, and we told him we will take care them by ourselves. I will update this post and hoping for a better solution. Thank you

I'm a fan of Hickory. Love it! I love it's STRONG variation! Yep. Variation is the word that can be used for Hickory. If you are going for "mid-tone" then it means the Hickory is stained. No problem. That's fine. Hickory takes a stain very nicely. But it will still have plenty of variation. The stain will even that out a little bit, but not entirely. The finish is UV cured urethane. I'm not very excited about that finish. If you are going for factory finish, you will want to work with the TOUGHEST finishes on the market (that's why you go with factory finished...for the TOUGH finish). The UV cured urethane is a ho-hum type of finish. Average would be the best way to describe it. The thickness of the plank is 3/4" = normal for sold. The plank width is 5" with random lengths UPTO 60" (5ft). That tells me there will be many planks in the 3' - 4' range. Again, this is ho-hum average. And with a wide plank product, it will need "glue assist". And Hickory certainly needs it because it has a bit more movement (less stable) than white oak. And then there is the "low gloss" format. The low-gloss finish on this depth of colour = nightmare to live with. It will show dust, etc as well as oily foot prints, sock prints, paw prints and will look hazy at certain times during the day. The "haze" is part of the chemical make up of the finish itself = that's how they take away the gloss...they haze it with a chemical additive. The haze goes away when you sand and refinish the floor. That's the only way to fix it. If you must have a mid-tone floor, I would recommend a TOUGHER finish (aluminum oxide or ceramic infused polyurethane) in a satin. Satin is FAR MORE livable. It offers a lovely glow without being shiny. It hides skin oils (like paw prints from dogs) because it is the same gloss level as skin oils....it isn't hazy....you get the idea.

I got Mirage Select & Better in natural red oak and it's quiet blonde. Much fewer knots and less busy than the lower grade of red oak. My floors were $8 per square foot for the wood. They also have white oak but I don't know what pricing is because I decided against the white oak because I wanted more of a contrast with all of the white oak cabinetry in my place. These aren't great photos because lighting is a bit off but in person my floors are very "Blonde"

@serenehome I’m considering the same floor! Did you use it? If so, how do you like it, can you share pics?