I realized after I posted that I just added more issues to think about; but you are correct there are tons of info and misinfo out there about floors in general. Nail polish remover is acetone, and what you removed was probably old-fashioned varnish which I think is soluble in acetone. I'm not sure acetone dissolves shellac - alcohol does that. It's not un common to have multiple different types of old finishes, for various reasons, (You might try some denatured alcohol, or vodka. I use grain alcohol which is the nuts, though sometimes hard to obtain because of laws trying to prevent people from misusing it. I actually have to leave NY and buy mine in VT, by preorder from a State source.) The cracks you see in August (and still now) are likely the narrow ones! Wait until late March rolls around after a full winter of heating. I can lose Bic pens in some of mine. That's when they are easiest to clean out, though. I wouldn't try anything other than emergency washing until the cracks are clean as there is no point moistening that junk in there. It's important that at the end of the season that the gaps are clean as they begin to swell back up. Dirt and debris trapped in the cracks as they close can compress the edges of the floor board, causing increasing gaps the next season. Of course old houses weren't built when there were effective vacuum cleaners so there's a lot of debris down there. As to washing: Murphy's has long been a standby, but has also acquired some (perhaps innaccurate) reputation as being hard to fully remove from floors prior to using poly urethane finishes. I will say this: about a decade ago I was visiting Montpelier, Pres. James Madison's plantation, (he was comtemporary pal of Thos. Jefferson) in VA. I happened to be visiting in the off season and got to wander around a bit more than most visitors. I climbed a staircase and encountered the curatorial staff working on an as-yet-unopened-to-the-public room. They were busily at work washing the floor of the room, with you guessed it: Murphy's and water. So if it's good enough for such an important and professionally cared-for house, it's probably good enough for mine. Otherwise I use Organic Linseed Oil Soap - imported from Sweden, doncha know. I got it from the site that sells the Silent Paint Remover. I find it's an excellent cleaner, smells nice and wasn't particularly expensive since I only use a little at a time. In olden days the floors were sometimes washed with lye, leached out of wood ashes, so I imagine a little Murphy's or Method won't hurt. Floors were also strewn with sand which was then swept up. (That's why you'll likely encounter sand in the cracks even if you're far from the beach.) Don't try washing unless you have a huge pile of rags on had to handdry the floor off at once. Yes, hand sanding or scraping is a one-room-at-a-time type project. More so than renting a drum sander. The only catch is how to meld the meeting point of applied finishes at the threshold when the adjacent rooms are not done all at once, if you don't have a raised threshold. One of the beauties of shellac is that it can be patched up or touched up, or joined together seamlessly anywhere, even in the middle of board in the middle of a room. It's not without its detractions however, the primary one being that it is not bulletproof the way modern poly is. OTOH, should trouble ensue you just clean the surface where the problem is of any wax and dirt and get out a brush and touch it up. It redissolves the old shellac, mixing it with the newly applied stuff and dries so the patch is invisible. Can't say that about any poly finish. You can get it completely off with rags and alcohol and start the whole thing anew if you want. The fix-ability and the reverse-ability have much to recommend it. It is also pretty easily DIY-ish, and cheap. You can search for more info using Google and here on thsi site. But be forewarned there is a LOT of anti-shellac prejudice out there by floor pros, and some people who are just repeating what someone else said. There are also some excellent reports by people who took the chance on it and are very happy. It is relatively slower to apply and more hands and kness sort of work. Don't try it unless you are in a warm-ish, but mostly unhumid time of year. You need to ventilate the room. It is not the worst stuff for breathing, but not benign either. Shellac itself (though not the carrier) is an organic product made from exudations of a beetle in India. I'm imagining you might be interested in seeing what can be learned from your floors. Here are two things to look for (get down on your knees with a good flashlight.) Look for little rows of holes running along the floor. The holes will probably close be together but the rows separated by about 21-27 inches apart. This is evidence of an early floor covering called ingrain carpet held down by tacks. Another thing to look for is evidence how the floor was finished originally (and to know if it has ever been sanded by modern methods). Drum and orbital sanders didn't exist, even sand paper as we know it didn't, so very sharp broadknives were used to scrape the floor flat and ready for finishing. If you hold a light at a raking angle in a place where the wouldn't have been much foot traffic, you may be able to see shallow 1/16th to 3/16 ths inch wide grooves on the surface. This are the still-remaining toolmarks of the original floor's finishing, you are looking at the hand-made work of the floor installer. If you can see the undersides of the boads, say y looking up at the first floor from the cellar, you may be able to see the saw pattern, which can tell you if it was made from logs using a hand-powered pit saw, circular saw, etc. This helps nail down the age of the building because of technology of locally available materials is often known pretty accurately. Have you sorted out which floors are the splintery-est? I have some fir and it has narrow, sharp, fierce splinters. The flat-sawn wide-board pine pretty mellow. Quarter-sawn oak strip is rarely that way. It's not uncommon to find many types of wood in a single house. It's worth learning the correct indentifications of both species and board type (flat, quarter, radial, T&G, butted, lapped, etc.) as sometimes choices of floor finishing techniques are limited by type of wood. Oh, I forgot to add: the reason I use old credit cards (and similar plastic things) to clean out cracks is that the edges and rounded corners are less damaging to the board sides within the groove than metal implements. Plus all the credit cards that are expired get another round of use if recycled into my floor tool box. Card companies used to send out plastic versions of fake ones they use to try and get you to apply for them. I was in plastic tool heaven, but, alas now the facsimiles are just cardboard. Another solvent to try is Soygel. It is particularly, though slowly, useful on floors. Leave it covered with plastic wrap for days, if necessary. Let time do the work, rather scraping it yourself. It also cleans up nicely which is something you can't say about most chemical strippers. All these solvents and the rags used to apply and clean off have the potential for spontaneous combustion. Either air them out on a line for days or dispose of them in a metal, closed container filled with water, and kept outside away from the house. HTH(elps) more than just adding to the overload. L. Here is a link that might be useful: source of Excellent Technical on Info on Care of Old Buildings (NPS Preserv. Briefs)

Wow, there sure area lot of opinions about shoes on shoes off. As an agent, sometimes we are requested to remove shoes. Typically it is on meticulously clean homes. Most buyers don't mind, some grumble, but I have never had a buyer say they refuse to take their shoes off. It is the sellers home. They have the right to ask people to remove their shoes. When my children were babies and crawling around on the floor, no one was allowed to wear shoes in my house. I simply didn't want my babies crawling around in what was on the bottom of people's shoes, it could be anything! Being in thousands of homes in my career, I can tell you, I have seen floors that have been damaged because of a woman's high heel. There is no doubt about the mark. It looks like a nail head path of holes. It is from a heel where the little rubber thing has come off the shoe . Most people don't ask you to take shoes off because they are afraid you will damage the floors,they don't want the outside dirt on the floor. There are some cultures where it is a must. But the bottom line is,if there were signs and most likely this agent was told when making the appointment to please remove shoes, it should have been done.

ok, this is an area where I actually know something! I sold and spec'ed hardwood for a custom shop before my mommy-life. The information you are getting here is correct. Engineered floors will give you 1-2 refinishings ON A PERFECT SUBFLOOR. One of the issues that sometimes arises if there are inconsistanies in the height of your subfloor. Because there is thinner wood wearlayer (before you get to the engineered wood) there is the chance that you can damage the floor irreparably when you sand it. Now I only saw this saw this happen twice, once on a loft job and once in an older home. The loft was more subtle as it was over concrete, the old house more obvious as they were DIYers and picked engineered flooring to try to negate their irregular subfloor (they neglected to tell us that that was why they chose engineered, we would have talked them out of it had we seen the floor first) Neither of their claims to the manufacturer were fully settled because both times they did not follow the guidelines for floor prep. The loft job was also a materials only job for us with their GC laying the floors but he insisted he knew what he was doing. A good engineered floor will not be cheaper than most of your nail down options because the production costs are higher. Now having said that, GOOD engineered floors certainly have their place in places where you can't put traditional hardwood due to height restrictions or concrete subfloors. My boss had a great engineered floor in his basement and it survived a flood remarkably well (it was ash, Kahrs brand out of Scandinavia and one of the beefier engineered floors and one of the pioneers) My Grandmother also had a Kahrs floor in her ground suite condo and she LOVED it and I was impressed by the milling. I'm considering it for our basement because it's warmer and less echo-y than laminate There has been a lot of 2nd rate engineered flooring coming out of China and being labeled for all sorts of different companies. You should be able to tell an engineered sample because the layers are sandwiched together and the tongue will be a different wood than the top (showing) layer. Distressed finishes are usually more expensive because of the extra step in manufacturing to make it distressed. That is different than just getting a lower grade of hardwood like a rustic or tavern grade (in solid hardwood). Those grades have more character but they often don't carry a warranty and generally have a higher waste percentage. Another thing to think about---if you ever have to replace part of the floor, you will always be able to replicate 3/4" thick hardwood but engineered floors are more like tile, they change and get discontinued over the years. You could go pre-finished, save the hassle of site finishing but with the thicker wear-layer a 3/4" nail down floor offers. Only you will know if you can handle beveling or not. The changes in milling the last 10 years are huge. The bevel in your better milled wood is tiny. I like Canadian mills, Model or Mirage for pre-finished. Remember that if you ever re-finish, the bevel will disappear and you will, essentially have a site finished floor. One benefit that many people don't know about? With a prefinished tongue and grooved floor you can have a good installer cut out a single board (or more) from your floor if it gets damaged which is why we did a fair bit of pre-finished in new homes since inevitably we would get call-backs at move in to repair trade damage (@#$%^ plumbers and their big wrenches!). Prefinished hardwood deals the best with shinkage and expansion issues because the finish is on individual boards. Site finished floors are more labor intensive but the materials are cheaper (apples to apples). They are what many people consider the gold standard however there are more steps and you don't always know how it's going to look until it's done. There is more chance of finish contamination and trade damage during the rest of the building process. We refinished 100 year old floors. I loved the idea that there wasn't 4 generations of carpet and crap in the landfill. Definitely a forever floor and it can usually be re-sanded for all but the very worst water damage (think entire house under water for a few days) If you are going with a wide plank, keep in mind your species and humidity level (and your ability to keep humidity stable). The wider the plank (with 3/4" thick flooring), the more obvious shrinking and expanding will be. If you take a 2" wide board and it shrinks 2%, it isn't very noticeable. If you take a 6" wide board and it shrinks 2% the gaping will be more noticeable and in the case of a site finished floor *could* pull your finish apart. You'll need to find a flooring contractor in your area with lots of experience. Most of the best hardwood shops ONLY do hardwood. Beware of carpet shops and many of the big box stores in many instances. Make sure they are accredited with the NWFA (national wood flooring association) http://www.nwfa.org/member/ good luck!

We installed Brazilian Cherry 9 months ago, and I think the flooring company recommends Bona, but I use a spray bottle of water with vinegar, and clean all the floors on my hands and knees. Just a damp micro-fiber cloth, the same cloth dries it, so it's not very wet. I shake it out at the sink after a few swipes. It's a long process that only lasts a day or so, these cherry floors are a nightmare to keep clean, and I've turned into a floor cleaning FREAK!!!! Family calls me the Floor Police!! Can anyone else relate?? You must have socks on, because toe prints will show and scuff marks drive me crazy, crumbs...spills, and unwanted scratches galore!!! I prefer to use my Dyson for bare floors daily and sometimes I gather all the crumbs with a micro fiber mop before I wet clean. I'm really happy to see others are using vinegar, because sometimes I feel I should buy the Bona cleaner. Vinegar was our first choice with ceramic tile, and now I'm using it on wood, hoping its still a good choice. No build-up that I notice. Someone said it takes away the shine, I haven't noticed that either. I would NEVER use Murphys Oil due to build-up. Try vinegar and water..and ONLY MICRO-Fiber cloths, I buy mine from Sams.