Glue made in the mid 60's could contain asbestos... you should have it tested. Hardwood and laminate manufacturers do not consider wood flooring glued to a slab an approved substrate for a floating application. But, if you decide to try it anyway, I would not put down a moisture barrier or use a 3in1 type underlayment padding. Just the plain stuff and do not completely tape the seams... just a piece of tape every few feet and cut some slits in the padding too. They are afraid of moisture becoming trapped in the parquet because all slabs emit some percentage of vapors.

Redroze, I'm just getting back online and seeing your questions, so I'll try to answer what I can. My new floor in the LR/DR was not pre-finished, it was all site-finished. I did put a pre-finished floor down in my office (no pics, sorry) because I work from home and didn't have time to be without my office for the week it would have taken to have floor sanded etc. The pre-finished does have a different feel to it than the site-finished. I wouldn't say it's grooved, just a more defined difference in between the individual planks. The office doesn't adjoin any other room, except the tiled hallway, so I didn't worry so much about the wood being different there. I see from your pictures what you mean about running the planks the same way and wanting to be sure things don't look odd. One idea might be to take up some of your FR planks, like the first 12 or so, and then put them back down interwoven with the new planks. That way there's not a clear line in between the 2 rooms, but rather a more gradual blending. Here's another couple of pictures, this time of my family room. The first one is a before shot of the hardwood floor + a rug-like carpet. The floor created a frame around the carpet. I had the carpet taken up and new hardwood put in where the carpet originally was, then everything sanded and refinished. You absolutely can't tell where the old wood was vs where the new started. In this case, the new is random width because it opens directly to the kitchen (as opposed to the LR/DR which is all the same width). So, one house, all new site-finished floors in the LR & DR, all new pre-finished floor in the office, original/refinished in the kitchen, and half&half refinished + original in the family room. Boy did we have dust! Hope this helps! New:

SJ McCarthy, our contract is stated we are responsible for the materials and we pay for the labor. Unfortunately we never met nor discuss with the owner but only discussed in details ( in the proposal) with the project manager who is the solely the carpenter.) We just found out there were a lot of the DETAILS from the proposal were not explained (per the PM,but who knows) in detail to the owner or almost like "bait and switch" - for example like item #2- he spent more time because the owner did not get him another helper to help him- I told him this should not be the customer's expenses-Anyway we are willing to pay for it. The owner was offering to renew and establish a new contract from the original contact ( we felt that he cherry picking the items from the proposal, we marked them up then again he decided not to included) for the unfinished works . Once he agreed in our 2nd meeting (another example: he agreed tiling our study room to be included from the original contact in our 1st meeting then when he write the REVISED CONTRACT- he wants to charge us ), but again we are facing the same old stories-he tried to change the wording. We were burned so many times and now we diligently review line by line knowing the owner's personality. He kept saying he lived by the contract-then I told him then he should honor the low estimated to install our engineering hardwood floor including removing the carpet-in the end he says he would honor but he did not including the cost in the new REVISED contract which we add into it - we are so tired with his games. So now we put a contingency - once we agree with the new contract, no more additional expenses from the previous work was done- and we do agree that we need to be notified first and need both signatures for additional expenses from the new contract. and no more point finger of "not included" since we have discussed in detailed and are in the contract. The new addition has a hardwood floor installed - with Dri-core. Once hardwood floor was installed- they are some areas squeak- we were told by PM -put a marked up then he would fasten without explaining to us-these would be additional ridiculous charges (PM told the owner, too-we told PM that they should explain it to us- ) Regarding the installing the engineering hardwood floor is for our existing rooms(concrete slabs that has plywood already)- we are told just to put a vapour barrier. Is it possible to let me know what brands for the glues have to be moisture resistant ($2/sf) or moisture PROOF ($3/sf).? The manufacture instruction suggests to use Franklin Tongue and Groove adhesive (cross linking polyaliphactic emulsion glue) www.titebond.com -any suggestions? This Applachian engineering hardwood floor - FLOATING only needs GLUE between the wood (tongue and groove per the manufacture manual ) then would be FLOAT - this is not to be GLUE DOWN on our concrete floor (could be glue down if necessary but not in our case). Here is the website- on PAGE 9 http://www.appalachianflooring.com/uploads/general/documents/engineered-installation-guide.pdf We trust the PM and we pay for it- we just want to move on and complete the project-It has been almost 10 months. We have to do what we have to do to protect ourselves now- The owner refuses to install our towel bar in our new shower without charging us, and we told him we will take care them by ourselves. I will update this post and hoping for a better solution. Thank you

if the parquet is in good shape, you can absolutely have it refinished. I like them. as for matching it, yes, you can buy more parquet oak tiles in the same species. It's a beautiful floor when refinished correctly. some are called 5 finger block oak parquet. this shows the thinner plank style butting up to it. (prob 2 1/4" or so) You can easily buy this other flooring and do it. if you do solid, it's stain on site along w/the parquet. (the parquet flooring has to be sanded w/an orbital sander, not a regular forward and back one. So make sure a good pro is hired to do it) look at how cool it looks in a dark walnut shade w/inlaid regular strips. great for any damaged parts what you could also do for the parts is a herringbone. (either solid or an engineered) Emily Hendersen talks about redoing her space w/this oak https://stylebyemilyhenderson.com/blog/story-herringbone-flooring If I had the choice, i'd do the herringbone. it's beautiful and completely mcm appropriate This is a natural finish white oak. and love the idea in the bathroom to feather in ceramic tiles in the same herringbone in the kitchen you could do something like this w/some cool cement tiles around the perimeter: walnut stain color. 5 finger block parquet matches the finger oak herringbone, below: you could even do the finger oak herringbone to match your parquet (the planks are shorter) longer sizes. you could also do a herringbone surrounded by the regular planks.