skip to main content

Drawers stick on F&P dish drawers

RNmomof2 zone 5

3 years ago

Both of our dish drawers have starting sticking recently and require a good tug to get them to open. They are over 10 years old. Does the seal just wear out or rot? Anything we can do to remedy this problem. I'm afraid I'm going to do damage to the door pulling on it.

Sort by:Oldest

Comments (3)

dadoes
3 years ago
You have two single-drawer units? Or one double-drawer unit?

"Over 10 years old" covers a lot of ground for the various model revisions. Citing the specific model number(s) is more helpful than an imprecise age reference.

Assuming you don't have one of the very early models that have inflatable seals ...

The seal (for each drawer) is part of the drawer lid and does not contact the drawer rim until a cycle is started and the lid motors crank the lid down.

The lid attaches to lid yokes at the left and right of each drawer, which in turn are connected to the screw-drive motors to raise and lower it.

Could be one (or both) of the yokes on both drawer have broken.

Could be one or both of the lid motors on both drawers have failed.

A drawer can be forcibly opened if the lid motors fail and the lid doesn't open ... but it cannot be closed again without damaging the seal ... the lid motors must first be manually cranked to raise the lid.

Could be the link support arm (which supports the wiring harness, fill hose, and drain hose) has broken on both drawers and something is dragging on the drawer ... but you didn't cite the model to confirm if you have the old-style plastic link support (which will eventually break) or the more-sturdy revised metal support.

There may be a few other possible causes.
RNmomof2 zone 5 thanked dadoes
RNmomof2 zone 5
Original Author
3 years ago
DD24DCTB6. I was hoping the answer was generic enough I didn't have to go find the receipt. :-)

I read this to DH and he just feels that the gasket is dirty or sticky (says the electronic tech). When opening, after the seal is initially broken, it opens just like before if that helps.
Related Discussions
Dishwasher Drawer- F&P vs Kitchen Aid
Q
Comments (1)
When researching the F&P dishdrawers, one interesting comment that was made that really hit home for me was something along the lines of "if you are going to get dish drawers, why NOT get the ones made by the company that has been doing it the longest and has the benefit of its own research and improvements". So, I thought about that, and did some more research and learned that indeed F&P did have some issues earlier, but worked hard to improve and correct any problems. I bought the F&P dish drawers about a year ago and couldn't be happier. Just the other night they once again proved themselves to me: in the top drawer I put in a scraped of large chunks only dish that I made scalloped potatoes in and in the bottom were the baffles (greasy) from the range hood. Everything was sparkling when done.
...See More
Fisher&Paykel vs Bertazzoni? F&P DishDrawers enough space?
Q
Comments (2)
The drawers work for my family of 4, but you do start to lose the advantage of the drawers if you easily run one big load a day. They do hold a lot though, and staggering small loads might work better than doing less frequent big loads. It's much easier to get someone to unload a drawer than a full size DW. You'll get used to whatever you have I suspect. I don't know what the advantage of stainless over plastic is, really, aside from sparkle...that's the least of the differences between drawers and traditionals. I can say that F&P customer service is really nice and responsive and you talk to a real human quickly when you call them (my stupid installer threw away parts...).
...See More
F and P dish drawer not always releasing the H20.
Q
Comments (15)
For comparison, this is how my hoses are run ... well, how they were run on the installation at my previous house. I moved the unit along to a new house several years ago, don't have a current pic but it's pretty much the same way. The DD was installed on the left of the sink. The two drain hoses come through an opening at the cabinet base, loop high as possible, tied up with a wire at left rear corner anchor bolt of the sink, then down to the plumbing connection. Backflow through either hose would have to go uphill from the Y-connector, through the high loop, down to the cabinet base, then into the drawers. Highly unlikely that would happen.
...See More
F & P Dish drawers - are you happy?
Q
Comments (61)
Yes, I will say that F & P did send out the repair guy a lot of times - for free. Since the trouble started before it was out of warranty, we finally got them to agree to pay for the calls that were past the 2 year mark (or whatever it was). We did pay for parts - after the 2 years, maybe $300 into it for parts, and one labor call before he started coming over for free. But the time off work, the time spent waiting, the sheer number of calls, and the two repairs that resulted in flood damage and a chipped granite countertop, after which both the repair guy and ourselves agreed he had no idea how to fix the thing...was too much. Obviously, this would vary from place to place. BTW, the Kenmore we bought last week arrived with water dripping out of it (about two liters), wet insulation and water all over the outside panel. According to Sears they "test" the pump before they send them out the door, and the pump should have pumped *all* the water out (this one obviously failed its test - the warranty literature, etc., was drenched). We decided to put the older Bosch into the butler's pantry and order an extra set of drawers to go where the dishwasher was in the main kitchen - we're giving up in a DW in the kitchen. The one flood (which ruined the brand new DH-installed floor - so much work) was enough, the parts on the Kenmore were so cheesy looking when we finally got it, it's a no-go (if we had linoleum in mind it would be different, but we're convinced we want wood in the kitchen, and we already have it purchased).
...See More
dadoes
3 years ago
Series 6 unit. It has (or should have) the updated link support. The model number is on a tag on the machine, visible between the drawers (usually at the left) when the upper is open. Not necessary to find the receipt.

The serial number is coded for the month and year of production if you want to know the age more accurately.

The seal should not be in contact with the drawer after the lid opens/raises at end of the cycle. The lid is raised with enough distance between the drawer and seal that it should release even if sticky.

Suggest the drawers be removed for access to examine the lid/seal.

The seal is integral to the lid, not a separate part/item.
RNmomof2 zone 5 thanked dadoes

Related Stories

KITCHEN DESIGN Idea of the Week: Customizable Dish Drawer

By Vanessa Brunner

Tuck dishes safely away in a DIY kitchen-drawer organizer

KITCHEN DESIGN Organizing Tips That Really Work: Pantry in a Drawer

By Vanessa Brunner

Deep kitchen drawer keeps pantry items tidy and at hand

KITCHEN DESIGN Discover the Pull of Microwave Drawers

By Rachel Grace

More accessible, less noticeable and highly space efficient, microwave drawers are a welcome newcomer in kitchen appliances

MOST POPULAR 8 Ways to Get a Handle on the Junk Drawer

By Laura Gaskill

Don’t sweat the small stuff — give it a few drawers of its own, sorted by type or task

KITCHEN DESIGN Get It Done: Organize Your Kitchen Drawers

By Becky Harris

Clear 'em out and give the contents a neat-as-a-pin new home with these organizing and storage tips

KITCHEN STORAGE How to Organize Kitchen Cabinets and Drawers for Good

By Annie Thornton

First, empty your cabinets and lose what you don’t use. Then follow these steps to keep your kitchen organized

GREAT HOME PROJECTS How to Add Toe Kick Drawers for More Storage

By Kathryn Peltier Design

Great project: Install low-lying drawers in your kitchen or bath to hold step stools, pet bowls, linens and more

KITCHEN STORAGE 8 Cabinet Door and Drawer Types for an Exceptional Kitchen

By Shane D. Inman

Pick a pocket or flip for hydraulic. These alternatives to standard swing-out cabinet doors offer more personalized functionality

TASTEMAKERS Pro Chefs Dish on Kitchens: Michael Symon Shares His Tastes

By KitchenLab Interiors

What does an Iron Chef go for in kitchen layout, appliances and lighting? Find out here

KITCHEN DESIGN Pet-Friendly Design: Making Room for the Dog Dish

By Mary Jo Bowling

In a dog’s life, you eat on the floor. Except in kitchens like these, where pets are factored into the design

More Discussions

Wolf vs SKS - 36" gas cooktop

1

Replacing standard fridge with free standing fridge

13

Quick kitchen question about fridge and oven.

9

Kitchen remodel

14

Refrigerator Temp Problems

1