Yes. I have sanded and finished subflooring for customers. Really no different from any other flooring finish work, except that you have to consider the fact that it happens to be a single construction floor system and, therefore, you have to take steps to protect what is below the floor when you sand and then apply stains and finishes. Anything you do above to the floor surface can easily find its way down to the space below...dust, stain and finish. You have to sink any top nails below the surface of the wood before you sand and continue to punch them below when necessary. You probably can never remove all tar paper lines and staining, but that is OK, as the floor will have a great look all by itself. I have finished these natural and stained a few. I also colored one green once at a customer's request. That one was unique and beautiful.

I realized after I posted that I just added more issues to think about; but you are correct there are tons of info and misinfo out there about floors in general. Nail polish remover is acetone, and what you removed was probably old-fashioned varnish which I think is soluble in acetone. I'm not sure acetone dissolves shellac - alcohol does that. It's not un common to have multiple different types of old finishes, for various reasons, (You might try some denatured alcohol, or vodka. I use grain alcohol which is the nuts, though sometimes hard to obtain because of laws trying to prevent people from misusing it. I actually have to leave NY and buy mine in VT, by preorder from a State source.) The cracks you see in August (and still now) are likely the narrow ones! Wait until late March rolls around after a full winter of heating. I can lose Bic pens in some of mine. That's when they are easiest to clean out, though. I wouldn't try anything other than emergency washing until the cracks are clean as there is no point moistening that junk in there. It's important that at the end of the season that the gaps are clean as they begin to swell back up. Dirt and debris trapped in the cracks as they close can compress the edges of the floor board, causing increasing gaps the next season. Of course old houses weren't built when there were effective vacuum cleaners so there's a lot of debris down there. As to washing: Murphy's has long been a standby, but has also acquired some (perhaps innaccurate) reputation as being hard to fully remove from floors prior to using poly urethane finishes. I will say this: about a decade ago I was visiting Montpelier, Pres. James Madison's plantation, (he was comtemporary pal of Thos. Jefferson) in VA. I happened to be visiting in the off season and got to wander around a bit more than most visitors. I climbed a staircase and encountered the curatorial staff working on an as-yet-unopened-to-the-public room. They were busily at work washing the floor of the room, with you guessed it: Murphy's and water. So if it's good enough for such an important and professionally cared-for house, it's probably good enough for mine. Otherwise I use Organic Linseed Oil Soap - imported from Sweden, doncha know. I got it from the site that sells the Silent Paint Remover. I find it's an excellent cleaner, smells nice and wasn't particularly expensive since I only use a little at a time. In olden days the floors were sometimes washed with lye, leached out of wood ashes, so I imagine a little Murphy's or Method won't hurt. Floors were also strewn with sand which was then swept up. (That's why you'll likely encounter sand in the cracks even if you're far from the beach.) Don't try washing unless you have a huge pile of rags on had to handdry the floor off at once. Yes, hand sanding or scraping is a one-room-at-a-time type project. More so than renting a drum sander. The only catch is how to meld the meeting point of applied finishes at the threshold when the adjacent rooms are not done all at once, if you don't have a raised threshold. One of the beauties of shellac is that it can be patched up or touched up, or joined together seamlessly anywhere, even in the middle of board in the middle of a room. It's not without its detractions however, the primary one being that it is not bulletproof the way modern poly is. OTOH, should trouble ensue you just clean the surface where the problem is of any wax and dirt and get out a brush and touch it up. It redissolves the old shellac, mixing it with the newly applied stuff and dries so the patch is invisible. Can't say that about any poly finish. You can get it completely off with rags and alcohol and start the whole thing anew if you want. The fix-ability and the reverse-ability have much to recommend it. It is also pretty easily DIY-ish, and cheap. You can search for more info using Google and here on thsi site. But be forewarned there is a LOT of anti-shellac prejudice out there by floor pros, and some people who are just repeating what someone else said. There are also some excellent reports by people who took the chance on it and are very happy. It is relatively slower to apply and more hands and kness sort of work. Don't try it unless you are in a warm-ish, but mostly unhumid time of year. You need to ventilate the room. It is not the worst stuff for breathing, but not benign either. Shellac itself (though not the carrier) is an organic product made from exudations of a beetle in India. I'm imagining you might be interested in seeing what can be learned from your floors. Here are two things to look for (get down on your knees with a good flashlight.) Look for little rows of holes running along the floor. The holes will probably close be together but the rows separated by about 21-27 inches apart. This is evidence of an early floor covering called ingrain carpet held down by tacks. Another thing to look for is evidence how the floor was finished originally (and to know if it has ever been sanded by modern methods). Drum and orbital sanders didn't exist, even sand paper as we know it didn't, so very sharp broadknives were used to scrape the floor flat and ready for finishing. If you hold a light at a raking angle in a place where the wouldn't have been much foot traffic, you may be able to see shallow 1/16th to 3/16 ths inch wide grooves on the surface. This are the still-remaining toolmarks of the original floor's finishing, you are looking at the hand-made work of the floor installer. If you can see the undersides of the boads, say y looking up at the first floor from the cellar, you may be able to see the saw pattern, which can tell you if it was made from logs using a hand-powered pit saw, circular saw, etc. This helps nail down the age of the building because of technology of locally available materials is often known pretty accurately. Have you sorted out which floors are the splintery-est? I have some fir and it has narrow, sharp, fierce splinters. The flat-sawn wide-board pine pretty mellow. Quarter-sawn oak strip is rarely that way. It's not uncommon to find many types of wood in a single house. It's worth learning the correct indentifications of both species and board type (flat, quarter, radial, T&G, butted, lapped, etc.) as sometimes choices of floor finishing techniques are limited by type of wood. Oh, I forgot to add: the reason I use old credit cards (and similar plastic things) to clean out cracks is that the edges and rounded corners are less damaging to the board sides within the groove than metal implements. Plus all the credit cards that are expired get another round of use if recycled into my floor tool box. Card companies used to send out plastic versions of fake ones they use to try and get you to apply for them. I was in plastic tool heaven, but, alas now the facsimiles are just cardboard. Another solvent to try is Soygel. It is particularly, though slowly, useful on floors. Leave it covered with plastic wrap for days, if necessary. Let time do the work, rather scraping it yourself. It also cleans up nicely which is something you can't say about most chemical strippers. All these solvents and the rags used to apply and clean off have the potential for spontaneous combustion. Either air them out on a line for days or dispose of them in a metal, closed container filled with water, and kept outside away from the house. HTH(elps) more than just adding to the overload. L. Here is a link that might be useful: source of Excellent Technical on Info on Care of Old Buildings (NPS Preserv. Briefs)

I'm curious to see the replies. My son almost bought an older house, 1951, the wood under the carpet is about 2"wide strips looks like solid wood, but seems to have a lot of nails. Is that how it was done back then? I wondered how it would look if he had them finished, but he backed out of the deal after the inspection. We are about to tear out decent wood because the sun has faded it and since it is not a big area it would cost a lot to refinish, and I hear the refinished floor would need to be done again much sooner than a new prefinished. I wish I could take out the old wood in a way that it could be used by someone, but I think it will get wrecked. The store I am using charges $3 sf to install it, the wood price obviously varies. They use their own employees, no subs, and did a nice job on our mbr and hall, so I will use them even though I dont know what an independent installer would charge. My maple will cost $5.54 sf, plus install.

When I hear someone recount something that makes no sense, I generally figure that someone misspoke or didn't hear correctly. Whenever I see huge variations (3x) in price quotes, I generally figure someone made a mistake. Maybe the third quote will clear things up. Whether wood can be refinished depends on the type of floor and condition. Since you're selling, and already having work done in the house, I'd be inclined to have all the floors redone unless the finisher can match it 90%. If there's any doubt, do it all. This assumes you know what prospective buyers are going to want. I usually recommend the opposite when people are living in the house. Colors and preferences here are all over the place. Usually it seems foolish to upend residents and spend their money when there's a good likelihood the next person won't like their choice, but your situation sounds different since you're already having work done. The only warnings I have about sanding painted floors are that you may find some cosmetic damage and you may end up with paint residual in some cracks.