My vent is a rigid vent, not a telescoping one. It is 4" typical rigid duct work to the outside except for the flex aluminum stuff that is at the big box that I put in. I have never done any of this before, so I read and tried to figure it out as best I could. The box and flexible duct work I got online at an outfit called the Dryerbox. I linked it below. The box is put in upside down compared to their pictures because my vent goes into my basement and exits the side of the house. Be sure to calculate the duct run that is recommended by your dryer manufacturer. Each 90degree bend subtracts 5' of run you have available as recommended by the manufacturer. So you want to have the least amount of bends. I don't think the flex connection counts though, at least it doesn't for my dryer. You can get these flexable auger like brush for cleaning vents. They sell them at the website I linked below and at Lowes. I used it for my old dryer and it works. You are supposed to be able to run the brush using your drill to spin it, from your outside vent. When we cleaned ours it was beneficial to be able to get the brush right into the dryer itself, attaching a vacuum to pull out accumulated lint. There was plenty. Regarding the water, I think where ever you can reach it and get it turned off is the important thing. I plan on turning the water off between uses, now that I have the set in my living area. My old set is in the basement and I didn't give it a thought. This laundry project has taught me a lot about better management of my appliances. I installed Floodchek hoses on my basement set. http://www.floodchek.com/ I bought 2 sets and gave one set to my plumber. He thought they looked like high pressure hoses. He liked them. Regarding your pull out. Could you have a top and a bottom pull out, then a shelving area with door to hide and access the vent, electric, and water? Here is another drawing of my setup. It shows where the vent goes inside the wall and down to the basement. There will be a door on the shelving area where I can pull out the shelves to get to the vent exiting the dryer on the side. I bought a Miele set and there is the option for side venting. There is also my water connection on the right side that isn't shown on this drawing, but is seen in my picture. I also have and outlet near the front of this cabinet for an iron. The bottom area will be open for a laundry basket, though I will have shelving available if I want to use them. The bottom area is where my electric outlets for the W/D are. The one drawer shown will be one of those pull out ironing boards. I do very little ironing but thought it could be handy. My counter between the ironing drawer and the shelving above will not be exposed, instead hidden behind the door (door not indicated on this drawing) When the door is open there will be the vent box and water hoses visible I'm afraid. But it will be all accessible. Current design of my setup, showing vent that is inside the wall: Here is a link that might be useful: The Dryerbox online store.

THANKS GUYS, Would either of you happen to have part number for the rubber washer, or know the size ? Also, What size is the cap nut ? I was thinking "If I Had to replace the valve", by removing the cap nut, this would expose the threaded shaft. From here, I would use a reducer down to fit the new shut off valve inlet. Then cap the original (in the wall) outlet to tank. This in effect would be two valves in Series, and sure beats the Hell out of destroying the tile. Next question ... Does anyone make a Reducer of that size, and if so where can I get It ?? Thanks Again, Nitrojc.

When making up IPS (Iron Pipe Standard) threaded fittings it requires the use of two wrenches, one to steady the pipe while the other is used to turn the fitting, or vice versa. When properly made up there should never be more than 1 full thread still visible.

I can go to a plumbing supply place and get it. Right now I soldered on a female adapter that is threaded. I then attached a fitting that has the 3/8 inch male. Not sure if that is correct but it is temporary until I get the new cabinet installed. There is currently a union that I can take apart to remove the whole assembly. Thanks for the reply. Not sure why HD does not carry this since they have hundreds of other fittings.