I think you would get better response if you posted this question in the laundry forum. Most dryers are pretty basic but Miele's have reverse tumble, which you may or may not be interested in.

the old ones are just fine. you wouldnt be missing anything. do you plan to stack them ? some have angled fronts and some have flat fronts

just update on this effort the electrician came out yesterday and added a pair of 220v outlets. This will enable me to run 2 dryers at once, if necessary. for the washers, i have purchased a spliter (Y) to feed the 2 washers, however, the problem is the draining of the waste water. i have a 2" outlet pipe but only 1 washer can connect to it at a time. so, to run 2 washers at once, i need a Y also. however, there isn't one like that in the market place. instead, i will create a simple Y using PVC pipes (stuff used for sprinklers). each outlet hose has an internal diameter of 3/4". I will put a 1/2" pvc pipe, which has an outer diameter of 3/4". Then this will feed into a 1" main pipe which will run into the waste drain. i will post a picture if anyone is interested....

Thanks all for posting. I have stalled out on the remodel but will be back in action this next week when my carpenter can start. I have a new carpenter coming to appraise the progress of the job and start next week. Long story, but this new carpenter is actually the one I wanted originally but not unavailable so went with someone else (who didn't work out). Here is a plan view as asked for, and an elevation. The two walls that create the corner where the W/D sit are both load bearing walls. The blue square in upper left corner is the Miele W/D stack. The gray square to the right of W/D is the cabinetry and where I plan to access the shut off valve and dryer venting. These utilities will be in the back wall accessible through the shelving inside the cabinet: This elevation shows cabinets to the right of the W/D and will have the shut off valve inside the cabinet, reachable through the shelving. This elevation rendition is not current. Instead, I plan to have doors above counter height, and have the below counter area open, without a door: Shut off Valve: I have a manual shut off valve with the drain hole (all in one box) mounted by the plumber. This will be easily accessible from the side of the set, inside the cabinet. Hoses: I have the Floodchek hoses on site and ready for installation. Overflow Pan: I was thinking of a overflow pan such as this one I have linked below. It has a 5 gal capacity and has a 24x24 outside dimension. Anti-Vibration: I still have not made a platform for the set but was thinking of 2 plywood 3/4" sheets with a sandwiched mass loaded vinyl sheet in between as recommended by Mongoct on the bathroom forum. Otherwise the anti-vibration feet that Deke mentions might work and a lot less trouble. I have see some anti-vibration feet on the Grainger web site for heavy machinery. I might try those. Here is a link: http://www.grainger.com/Grainger/ecatalog/K-16/N-/No-0/Ntt-anti+vibration+pads?Ndr=textsearchesinbase%2Btrue&sst=subset Dryer Venting: I have been planning to bring it out the right side of the set, and accessible in the back of the cabinet, for cleaning ease. I may not be able to place it in the wall as the studs are in the way of the joist space for the ducting. If I can have the carpenter frame out the stud wall for a dryer vent I will. I want ridged venting, and have it accessible to the side of the dryer (not behind the dryer). If this can't be done within the wall space, I will have to put a hole in the floor in front of the wall for the venting, concealing it behind the cabinet. though this will make it vulnerable to bumping with the laundry basket that I plan to keep in the lower area below the counter. My machines are at the warehouse waiting. Any comments or recommendations are welcome! Thanks again :) Here is a link that might be useful: slide-n-fold pan