I suggest getting a traveling sprinkler that follows the hose. It won't be quite as ugly and there is only a single hose to deal with. It's not that difficult to put out of sight when not in use. By adjusting the arms, you can get it to water a narrow strip or a very wide strip.

I have setup something very simple, even I can do this. What you need is a bed with a cover (four corrugated iron sheets and a see through roofing sheet you'll get both for free). Then you need a timer. You take care of the minimum time the timer can do, because not all timers can do times like 10 seconds some start with a minute. The timer works with batteries. At the tap you mount the timer, then either a piece of hose or a black plastic pipe for irrigation into you bed. There are misting valves, which are inexpensive and come in packs of 10. If you do cuttings you buy risers too which are little plastic tubes. All what you do is you push the risers into the polypipe and mount the sprinkler on top of it. Before you do that you get some sticks and thin wire. I place the sticks in the beds were I want the sprinkles and fix the polypipe to it. If the risers are a bit crooked I can fix them to the sticks. This way you can move your sprinklers around a bit. And don't forget and end cap for the polypipe.

If your emitters are failing: 1. Keep your drip heads above your mulch to keep the dirt out. 2. If it is a new system, flush the lines before installing the dripper heads. I have installed about 1000' of 1/2" tubing and another 1500' of 1/4" tubing to my approximately 800 dripper heads. A rather large system on four zones. Three years ago (first year), I had two dozen or so failures, but I didn't keep the heads off the ground. Now I do, and failures do not occur. Then again, I also switched manufacturers for the replacements, but the original ones not replaced are still doing fine. I use 1/2, 1, and 2 gph drippers, they all work equally well. I also had used a soaker hose, the 1/4" kind with a hole every foot or so. NOT!!! The holes clog and was totally ineffectual. I pulled almost all of it out, I have a few sections that are still working, but they are only watering very xeric plants that get enough water if even 2/3 of the holes were clogged. My system uses cistern water (10,000 gal tank buried in the front yard, water pulled out with a shallow-well pump), so hardness isn't a problem. The pump puts out 30-60 psi, I do not reduce it, and the only time an emitter has blown off it has been because of operator error. If you are using well water, then you may be getting sand and junk inside your lines clogging your emitters. Install a filter and you should be in business. Incidentally, I live at 7000' just east of Albuquerque, and the area around my house looks like a dense jungle of nothing but native plants with penstemons (at least 8 varieties), coneflower, chocolate flower, hyssops, yarrow, yucca, golden currant, sand cherry, salvias, thymes (non-native, but I wanted the groundcover), sumacs, and at least 20 other native species, all irrigated by emitters. Wouldn't do it any other way! Scott

I have an Electrolux oven and it works great but I would get an extended warranty to cover any possible problems with the electronics or the blue enamel. The blue enamel failed at about 41/2 years but luckily I did have an extended warranty and it was fixed. Do not buy the service plan from Electrolux as the blue enamel is excluded on their warranty. "This Service Contract does not cover repairs which are necessary because of improper installation, cosmetic damage, normal wear and tear, negligence, misuse, abuse, alteration, rust of any kind, service or replacement of porcelain enamel, exterior and interior finishes" This is from the Service Contract Terms and Conditions It also spells it out on the Icon web page Read any warranty that you buy to make sure the interior porcelain is not excluded.