This old thread got revisited. @dani_m08 to answer the question about extra probe, I believe I ordered an extra one when I bought the set up. The probe wire is just setting in the junction box I think but honestly I cant remember. When I laid out the underfloor heating and the probe, I just ran another probe near the first probe, and it was then sealed into the floor self leveling compound as per instructions. then the end was just threaded into the wall like the one that would be live, and not connected, but just laying there in the box. Regarding the tile layout. I just decided to run it this way, after getting instructions on the 90Degree way, IIRC. The herringbone that I love is from my childhood and the side walks in my neighborhood that all ran at 45Degree. so that to me is herringbone. I know you posted on @sochi thread about her amazing bathroom and a wall mounted faucet. I would totally do it if I had the right sink for it. In my case I had made my sink out of soapstone and an integrated backsplash. The pictures of this bathroom reveal are no longer available because of the use of photo bucket, when it was Gardenweb. I did not keep my account with photo bucket. I'll add some of the reveal pictures so you can see the sink and floor. Regarding the sink there is no ledge for water to drip from my hands when using the faucet. The water drips right into the sink. In my other bathroom with a deck mounted faucet I am always wiping up drips and it is a nuisance. I much prefer the setup for this sink. Below: I love the flush finish from the faucet to the bottom of the sink. nothing drips on a counter or edge of a sink. Below: looking in from the doorway. Below: Here I am finishing up the sink. the backsplash was epoxied on as a separate piece. The whole soapstone install in the room took next to nothing to buy as they were all small pieces that I epoxied together with a 3 part stone epoxy. Below: this is the counter at the tub, and is in 2 long pieces but I was able to epoxy them together at there edges to make a wide slab for the top. All the soapstone was finished with a 60 grit sandpaper to be rough and this lovely soft tone of blue/green/gray/white. I did not oil it so this color tone would remain light. Below: If I recall correctly @sochi helped me decide on this Hubberton Forge Mirror. I have 3 different metals in this room, but they are all a cool silver to black color. Below: the center of this tower shares space with the kitchen on the other side of the wall. there is also some extra space that houses some electrical wiring. this is an old simple house. this bathroom was an add on when it got move to the farm in the 30s IIRC. The plumbing was all rearrange and some of the details that were orignially there I kept but updated it, such as this tower feature. The old one went and the carpenter did a wonderful job with this one. Below: This feature was another thing I kept from the old bathroom but flipped it from the other end and had the carpenter put drawers in it. Before it was a hell hole. things got lost and the build was soooo old and creapy I didn't like using it for storage. Now it is perfect for storage.

We put a Delta Addison single handle faucet in DH's bathroom. My goal was to minimize mess. Also wanted a high arch and a water stream that went well into the center of the bowl. It started out with a single handle and I decreased the mess even more by installing a Tapmaster. We have them on all the sinks in the house (starting with the kitchen in 2002). It's not electric or battery operated. It's tied into the plumbing underneath the sink. A plate is attached to the toekick. Just gently pressing on the plate with one's toe activates the water. Also, consider installing the faucet at the 10 o'clock or 2 o'clock position so your child can reach it better. This one is installed on an extra tall vanity (husband's bathroom) and my 7 and 9 year old grandbabies don't have a hard time reaching the faucet or usinng the Tapmaster. I like the fact that there is so much room for hands and arms to get under the height of the Addison. And installing it to the side, helps a LOT with the ordeal of trying to clean between the sink and backsplash.

I am not a plumber. I started trying to fix the faucet that spurts out water when it turns to the hot side. The water spurts from under the handle into and then out from under it. Last night the pipes started to leak. It looks like it leaks from 4 places. The hose that attaches to the hot water drips. Three of the connections. Im willing to try it myself before we bring in a plumber and take the risk. We could go without the sink till this virus blows over. Here are better pictures marking where it leaks. When I turn on the faucet, most of the water goes down the drain. Some of it leaks frm where the pipes connects under the sink, the two parts where the pipes connect, and the hose for the hot water. The hose for the hot water I'm not sure where the leaks starts for it. I just see water dripping down it and dripping down. You're saying I should just replace the whole handle instead of using the warranty. If I leave that for last, how do I first fix the pipes that are leaking? Is it an issue that everything where the water hoses connect look rusted? This would be my first time doing something like this and its a good time to force myself to get it done. I don't have a wrench that is wide enough to wrap around the screw to tighten it.

I have used a vessel sink with a freestanding faucet mounted to the right, and it posed no problem whatsoever with usage. The water flows out toward the center of the sink regardless. Some people even mount their kitchen faucets on the side or in the corner. Most people would install a faucet handle to the right or in the center but never to the left unless you were legitimately left-handed. Most faucets won't even support a left handle installation unless specifically marked as a left-handed faucet. You could learn to use it, but I think even despite holding implements in the right hand, you'll ultimately find a right-handed faucet easier to use. Without photos of your space it is hard to comment, but seems to me that the top-mount will fit better in your space.