ThatÂs what I was afraid of. I didnÂt want to put ideas in peopleÂs headsÂbut that is the reservation I have. I think having to use it on one side of the wall, asymmetrically, doesnÂt work. I was SO sure it would look great, and be really like the finishing touch in this room. Darn! The thickness, bulkiness, of it bothers me too, in that place. Too much mass. I thought, before I tried it, that it would balance the weight of the solid looking vanity. Instead it just makes it look like too much weight on the left side of the room and nothing on the right. Having to one side bothers me with the light fixture too, and I love that light. It doesnÂt show well in the photos, but is a stained glass repro I ordered from a craftsman lighting company, in a custom size. The mirror is discontinued, so I canÂt get another to balance it better. It doesnÂt look right centered on the big mirror either. Too odd when you are standing in front of the vanity. Sigh. I love this mirror. Buying this one when it went on clearance was what made me decide to have a craftsman bathroom in the first place! (Well, that and it opens off a craftsman family room.) I have one open wall on that room, where I used to have a framed picture. IÂll try propping it up there. The craftsman family room already has a mirror.

Thanks marcolo. I think I'll go over there w/ a big mirror and make DF stand where the appliance cabinet will go and I'll stand in the breakfast nook and see what is reflected because that is where most time will be spent, I think. mtnrdredux- I originally wanted a range and I agree with you completely that it would look much better! I looked at the fratelli onofri in blue and was very, very close to buying it, but I didn't like the brass. And I think a lacanche (or even its cheaper friends) might be a bit of a waste in a kitchen where no one cooks. In general, though, I didn't love the whole idea of the range w/ the low ovens either. Like I said, we do use the ovens to reheat b/c DF won't use the microwave or eat microwaved food. I don't want to bend down to get stuff in and out, and I really do not like the idea of a low-to-the-ground range with a really sniffy little doggy who sticks his snout everywhere. I'm afraid he'd get hurt when the range opened and I won't take any chances on that. And I know I'd have snouts pressed against oven glass and possibly paws scratching the door if he smelled something cooking (and being a beagle, of course, he'd always smell anything cooking!) So, it is ovens for me. Plus, we already bought 'em (a 42 inch miele cooktop only b/c it was a floor model and we got it cheaper than most of the "low end" cooktops) and the floor model jenn-air ovens.

thanks all. --probably thought I'd gone away, taking so long to answer. It just seems one "challenge" follows another. The time goes by and you try to hold things together or repair things including your body and sometimes, things just keep coming. Hopefully, I'm forgive for being long time in answering. It's been in & out of docs. for me and tonight, wife goes to hospital. I managed to get a small, very small, strip piece of the paneling off, intact. I used a blow dryer to heat it. The adhesive cement is very, very strong. the blow dryer took a long time to heat the wood--I thought it was going to scorch , before the paneling came loose, but I finally got it. That 4"x4' section took over an hour of work! There does seem to be though a magic temperature, if I can get up to it, the adhesive softens enough to let me hammer a putty knife between it and the wood, other wise--no go. the putty knife won't cut it and the piano wire I tried to use, broke. I hoped that was the piece that would give me access to what I needed to work on, but no. I'll have to remove at least, maybe two, of the full 4x8 sheets. If I destroy this Walnut, there will be no way to replace it. And I do not want to have to figure out some other way to refinish the basement--I guess I could glue sheet rock to the walls, if I glue enough shims in first. I just hope I can get the panels down. You'd think that 30+ year old glue after being so old and going through freezes and thaws would be brittle and give way, but it sure doesn't. Probably the easiest way is to pry the furring strips from the walls and try to put them back up? Because of the unevenness of the concrete walls the strips are glued on both horizontal and vertical. And to get them off, I'll have to take down the entire wall! -- ouch! Is that the only way? I did such a great job putting this stuff up, I can't even see the finishing nails I used to make certain the panels stayed attached to the strips while the glue set. Then of course, I dabbed a bit of paint, the same color of the dark, vertical seams they are in, on the nail head. they are virtually invisible. To find them, I hope a magnet will work. If I pull off the furring strips, they won't be a problem. If I try to take off the paneling, I'm not certain if I have enough room to drive them through the panels before they hit the concrete. What a job. In removing the one little piece of paneling, I learned that I'm going to have to pull an entire corner of the ceiling tile down, as well. It just gets worse and worse...or maybe I should look at it as an exciting challenge? Let's see if I can do it? --yeah, right :( Instead of using a hair-dryer to try to heat the wood, what about trying an electric iron? Think I could do that without scorching the paneling? If so, how high of heat would you set it to and what would be good to put between the bottom of the hot iron and the paneling? --I don't think laying an iron, directly on the walnut, would be very good for it. Or should I just give up and try to separate the furring strips from the wall, leaving the paneling attached. --What a nightmare it was putting those up--absolutely nothing was plumb, level. It took hours and hours to get them level and plumb. Maybe there's an expert way to get these down--it'll take at least 4 people to take a wall all in one piece, especially to not cause damage to any of the panels. Then, how do I get it back up? Is it time to throw the walnut away and put up sheet rock? Bob

OK USE-2 is one of the service entry cables. You don't need to enclose it in conduit except where it needs to be protected. If it goes somewhere where it needs to be protected from damage, then conduit (or similar) is required. As near as I can tell (going through wood joists in your post) conduit isn't required. HOWEVER, you can not run the ground as a separate wire. You're either going to have to get cable with the appropriate number of conductors or run conduit and individual conductors.