Here's a vid for comparison of my Fisher & Paykel AquaSmart running two sets of sheets (queen and twin) and several pillow covers on the designated Sheets cycle. Run it at full-screen and 2x speed to see the rollover more clearly. Wash period starts at 6 mins 55 secs. Sheets cycle on AquaSmart is a specific deep-fill level, although not as high as the machine above. It's for sure too much water for one twin set of sheets, almost too much for one queen set, good for both sets together. Agitation alternates through three patterns -- long slow rotation, long slightly faster, short faster.

RE: Samsung Top-Loading Washer. The tub does rotate to fill the machine, but the water sprays around the edges, not toward the middle. I watched the entire cycle by shining a flashlight through the glass top. Water sprayed around the edges until the predestined amount was achieved. The pair of sweat pants in the middle floated, but never - throughout the entirety of the cycle - did the leg EVER submerge in the water. The gentle side-to-side swishing did, however, manage someway or another to tangle the sleeves and legs that WERE submerged to the point that it knotted them and threw the load off-balance. I’ve been doing laundry for quite a few decades now. My parents purchased a washer/dryer when i was about 4 years old and those appliances managed to wash clothes that looked and smelled clean and better yet - they did it for close to 40 years. I learned to do laundry with those appliances. My mother taught me how to place items in the machine to make sure the load was balanced and then choose the appropriate water level, temperature, and wash cycle. We didn’t struggle with unbalanced loads or tangled clothing. You set the machine, started the cycle, and walked away. When you came back, the load was done and ready for the dryer. I find it insulting that the companies engineering products now assume that I’m too freaking stupid to make my own decisions about the appropriate settings for something as simple as washing a load of laundry. I’m not so stupid as to stick my arm into a moving spin cycle and I actually parented my children to the point they knew that I would not allow them to climb into the appliances and/or drink bleach or eat detergent pods (so no need to lock the freaking lid of the washing machine). I managed to raise my children without child-proofing my house and treating cleaning products like we were housing plutonium. I taught them how to do age-appropriate chores and safely use household appliances. Fast-forward to now … Instead of cultivating an educated, self-reliant, intelligent society, we’re engineering with an attempt to make everything idiot-proof, consequently producing generations of idiots that can’t make reasonable decisions about their everyday existence. Good grief. And quite frankly I’m sick to death of hearing how environmentally friendly a company is that produces and “energy efficient” appliance that will need to be replaced every 8 years or so - the technology has existed since my childhood to produce a product that will last 20+ years. How environmentally sound is it to save a few gallons of water, yet send THREE machines to the landfill during the same time-frame that we used to send only ONE worn-out machine?!?! There is a serious disconnect with common sense going on here - I’m sick of things engineered for the lazy and the stupid. That washing machine sitting in my laundry room has delivered to me a resounding message from Samsung - and the message is … “We think you’re a blithering idiot who’s too stupid to operate a washing machine, so we’re taking the ability to make ANY decisions away from you.” We have computers in kindergarten classrooms, but society thinks adults are too stupid to learn to use a washing machine …

This recall is about users selecting the wrong cycle (Normal or Heavy Duty) when washing bulky or waterproof/resistant items such as bedding (comforters, mattress pads, bedspreads), shower curtains, sleeping bags, parkas, and the like. Every video I've seen on YouTube or news feeds covering an exploded washer that still has the load in it, the item(s) are as such. The explosion happens when the machine balances for spin, revs up to maximum 1,000 RPM (or whatever it may be), and the balance condition shifts due to sudden release of a pocket of retained water from the item. The manufacturer is cited as being at fault for not designing a safety system to stop the spin. Seriously ... there's NO WAY to INSTANTLY stop the mass of the washer drum and clothes load from spinning at 1,000 RPM (or higher in some cases). The electronics and sensors did their job for balancing the load at the start of spin. There's no way to anticipate that the balance conditions would change. The recall involves adding a security bracket to further secure the machine top, AND stickers that 1) relabel the cycles such that the Delicate cycle is designated for Bulky/Bedding, 2) warn that catastrophic damage may occur if the wrong cycle is used for such items, and 3) that waterproof items are not to be washed. Delicate runs a slower spin speed which serves to avoid the high g-forces and catastrophic explosion if balance conditions change after-the-fact at higher spin speeds.

I joined gardenweb to post on hvac but the second thing I have been dying to do is post on the Duet washer. Mine replaced an older front loading Maytag Neptune that was great for our clothes but broke down too often. Whirlpool bought Maytag and the Epic is the same as the Duet...we bought the Duet. I hate it. What I mean is...I hate it! I have only had it a few months and should have listened to the reviews I read before I bought it. I read about tangled clothes and snagged towels. I have no problems with clothes being clean. I use HE Tide and a bit of Biz (HE amount) and always Spray & Wash stains because my kids are 6, 9, 10 and quite frankly, are little dirty animals. Main issues: 1. The clothes, especially adult size, but long pants and sleeves on kids too, get tangled around each other--alot. Mine look just like the picture posted already. The saleman told me to jam in every towel or 20 jeans, etc. and push the door closed. I have never done that and can't imagine it. Sometimes it is so tangled, I have to pull about half the ball of clothes out and let them fall all over the floor as I untangle each item. 2. There is so little water that things end up nearly dry. Good, you think--but they are so dry, wrinkles are setting in before you even put them in the dryer and then the dryer really sets in those creases--especially the jeans. I also find some things, especially towels and t-shirts are noticeably less soft. 3. Towels, especially the really good, plush (expensive) ones that you love, come out snagged--alot, big long snags. I am guessing there are burrs or something inside the drum holes or something in there catching the loops. We are building a new house and this machine will not be coming with us because it aggravates me so. Here are some of solutions I came up with to help make laundry less aggravating with this machine. 1. I never pack it too full. I would rather do an extra load than take the extra time to separate the clothes to put in the dryer. I feel they probably get cleaner when there is less to get twisted around each other anyway. 2. To combat wrinkles I never spin on high. I will do normal wash, med spin or I will even go to heavy duty wash so I can access the low spin button. This keeps them wetter. My old Maytag Neptune dryer has a sensor so it runs only until it senses they are dry and works great. I keep a spray bottle of water nearby and spray the jeans and pants legs' creases and smooth out the wrinkles then do a loose fold before I throw them in the dryer. I also shake out the shirts to their normal shape. It takes time but it does help. 3. The towels...well they snag. My only solution so far is to never do a load of strictly towels. Towels alone in a load guarantees snags on some. I try to mix a few towels in my other loads so they have a fighting chance to stay away from the enemy--wherever it is. As for avoiding problems like moldy odor and the such, I try not to leave things in overnight, or throw them in a basket or leave door open if I don't dry things right away and then leave the door open when not in use. My old Neptune had a class action law suit about mold issues, although I never had the problem, so I am precautionary about that. I also wash my cleaning rags once a week or so in just bleach and that may help. Sorry for the long drawn out deal but I have been perturbed about this thing and have never joined a forum to vent. Although reviews I read elsewhere before I bought mention the snagged towels, I don't see it as much in this forum so I think it is not a complete design flaw and something in only some of them. We are under waranty and I also have the extended warranty. Maybe something can be done about that...a new drum or find a screw or something. I will make that call today and see what they say. Good luck to those who choose this washer or if you already have it and have these issues. If anyone would like to recommend a fantastic front loader with no problems, I am all ears. I may look at the LG or Bosch when we move.