This morning I caught the system just as it turned on (my ears are now trained to listen for the click of the tstat and the fan coming on.) This time, when the tstat started heat all by itself, the Aux Heat call did not come on. I have a feeling that anytime I try to force the heat on myself, the tstat is seeing a large enough delta between set and actual temp that it is kicking AH on. I will have to watch the operations over the next few days to see if it consistently works without AH. In the mean time, the breaker to the heater pack is off to avoid the toaster. I have decided to send an email to Honeywell tech support on the CPH setting for my tstat. Now that I understand what the CPH setting does, I need to know how the logic is implemented. For example, my tstat setting for Compressor Cycle Rate is set to 3. Does the tstat bleed these 3 cycles per hour (max) uniformly over an hour of time - or does it simply allow 3 on/off cycles in rapid succession, and then no more for the rest of the hour. If the allocation is uniform across an hour, then the Aux heat setting (which is currently 9 CPH) could be adjusted lower to keep Aux Heat from popping on so quickly - like when I increase the tstat setting by 2 degrees. Again - if it is a uniform distrubution of on/off cycles the tstat would permit Aux Heat to come on every 3 minutes with a 9 CPH setting and that is too frequent. So the CPH adjustment may in fact be part of the solution. I have also discovered a nagging issue with my second story heat pump. That unit is actually zoned - where 3 bedrooms each have their own tstat. My guess is that the CPH setting for each tstat is set to the recommended default (3 CPH) which means that there are actually a total of 9 CPH allowed (3 for each tstat). That explains why that unit kept cycling so frequnectly on me last winter. I believe that a CPH reduction is probably warranted in each of those tstats and that would reduce the number of total HVAC cycles upstairs. The downside is that some rooms way have a wider tempertaure swing and then a longer run to get up to the set temp. But I would rather have a reduction in cycles as long as the swings are not too big (which could cause Aux Heat to pop on). Imagine Room 1 calling for heat and getting serviced - then shutting off. Then a few minutes later, Room 2 does the same thing, then Room 3. If I stretch out the ON/OFF times in all rooms, I will increase the probability that heat calls will overlap. I will check on the L line. I believe that my tstat does not use L becasue I get no alarm lights when the compressor locks out - and I would like to have that. There have been cases where the compressor has locked out and the only way I knew it is when it got very cold in the room and I opened up the heat pump cover to see the red light on the contoller.

KitchenAide like many brands are part of a conglomerate that offers relatively similar products with feature differences at significantly different price points. The conglomerates can sell the brand equity out for a 'fast buck' which unfortunately is common today with everything being so short sighted on the next Wall Street quarterly report with executive bonuses paid based on stock price. KitchenAide mixers are one of the prominent victims of this short sightedness. My old 5qt 300 Watt mixer is ~35 years old and is much better than the newer cheaply constructed ~600Watt ~6qt models of today with their plastic gears and other trade offs. With these conglomerate companies and brands, there are still some "sweet spots" for both price and quality. One particular good stand out was my KA Oven that exceeded all my expectations for cooking quality. It never had a problem the entire time I owned it so, what else is there to say?

Here's a random observation for the morning...I only took 2 cuttings this fall to try and root over the winter and both appear to have taken. After reading one of the other threads about biochar I took a handful of small chunks of burnt pine from the fireplace and mixed that into the soil when I planted them. That is the only new difference from all my other failed cuttings (I do not have a good success rate! These are #4 and #5 out of hundreds of attempts). It may or may not be what made them both work, but I thought it was interesting to note.

Hi Natalie. We bought the Lounge ll sofa (2 of them) because our grown son has them and over the past 5 years with kids and dogs they wear like iron. I had the very same concern as you. I really don’t like the really deep sofas and worried too. But, we always seemed to be very comfy on there’s. We bit the bullet and got them 5 months ago for our new house. They are beyond great. Very comfy, and the depth is not a problem. We longe around on them all the time. If I ever feel like I want extra support, I throw a pillow behind me. But, to be honest, my feet are almost always up on the couch with me. Lol We picked out the fabric in Taft. (See photo). I’m not familiar with the fabric you are talking about. My son has a microfiber and it’s great.