Parquet must be banished?
artsfan
3 years ago
last modified: 3 years ago
Featured Answer
Sort by:Oldest
Comments (38)
Related Discussions
I've been banished :/
Comments (24)I'm not a cop, not military, and I wasn't doing anything wrong, exactly.... One of my buddies had just turned 18, and we were all at a party. Well he showed up with a 15 year old girl, and we said no way. He locks himself in the bathroom with her (what a gentleman), until he gets tired of us pounding on the door calling him a pedophile (not technically accurate, but the point wasn't accuracy). So he takes the girl up to his car. Another buddy and I went up to the car to convince our friend the error of his ways. After pounding on the car windows, this friend eventually gets out and yells at us. At that point, my other friend pulls out a can of pepper spray - not a stream but a cloud for crowd control - and sprays a huge cloud of it into the wind. The cloud expands, sort of stands in the air a moment, and then blows right back at us. Almost cartoon-like. We inhaled this cloud and the effect was immediate - ripped out feeling lungs, raw throat and sinuses, incredible mucous production, drooling, and eyes that can't open from the stinging and the tears. We were laughing through the snot and the pain, though....just our luck, try and do a good deed.... We were fine in about 15 minutes. Josh...See MoreInstalling wood parquet floor : any tips for us?
Comments (2)The metal strips are embedded in the underside crosswise to the parquet strips to hold the tile pieces together because these strips are not glued to one another. Presumably any cut edges will be hidden by edge molding so a jigsaw is ok, even if the cut is rougher. When I installed my oak parquet the same way as you are, I used a radial arm saw for most of my cuts: I simply marked where my cuts would be, and then pulled out and snipped off the part of any metal strip that would be in the way of the radial arm saw blade. You will have to use a jig saw for any complex cuts, but bear in mind that the metal strips can get dislodged by too much vibration, so it's not a bad idea to put masking tape on temporarily to hold everything together. When you have applied the adhesive, set a tile down as close as you can to the adjacent ones so that, when you slide it into position, you don't have adhesive being forced up by the sliding action and showing on the top surface. Keep some paper towels and solvent handy, because you will occasionally have some smear to cleanup. Use the solvent sparingly if you have prefinished parquet. Like any tile job, doing the layout, and then getting the first tile row completely straight is the critical part....See MoreExterior Brick Paint: Banish the brown!
Comments (32)I like what was done beneath that center forward facing gable over the entry. Removing the few feet of siding just above the garage door and adding painted treated plywood then using the same width boards to "frame" that space and battan the seams/spaces between the plywood pieces could be worth considering. You might even tap your inner artist and create a unique design....See MoreAvoid Indus Parquet Flooring
Comments (6)Did they use a maid for cleaning? I've known dozens of floors that were ruined by maid services. The other thing: a floor doesn't suddenly fail when it a 'bad batch' after 10 years. A bad batch is found VERY quickly. As in 'less than a year'. Even then...the same questions apply to what I've asked you (which you have chosen not to answer). To PROVE it is manufacturing issues, you MUST be able to problem solve. That means you must investigate ALL OTHER possibilities before you yell out to the world, "Hey! This stuff is cr@p! Don't buy it!" The chances are extremely slim for a manufacturer to be found liable for poor manufacturing after 10 years of the flooring in someone's home. So yell it to the mountain tops...my question is: Why were 1/2" laminate wood floors (again, is this laminate flooring or wood flooring???) in a HIGH END home? A high-end home would demand 3/4" hardwood floors with a 6mm wear layer. And does the home have a WHOLE HOME humidifier/dehumidifier? Or both if needed??? Questions about your complaints remain....See Moreartsfan
3 years agoartsfan
3 years agoMe AGirl
3 years agoPatricia Colwell Consulting
3 years agoartsfan
3 years agolast modified: 3 years agoloobab
3 years agolast modified: 3 years agoartsfan
3 years agoloobab
3 years agoartsfan
3 years agolast modified: 3 years agoSabrina Alfin Interiors
3 years agoBlueberryBundtcake - 6a/5b MA
3 years agoloobab
3 years agoartsfan
3 years agoartsfan
3 years agoartsfan
3 years agoMe AGirl
3 years ago
Related Stories
ROOM OF THE DAYRoom of the Day: Bright Red Dining Room Glows in Fog City
Mist can put a damper on the mood in San Francisco, but this lively room fires up the energy
Full StorySELLING YOUR HOUSE7 Must-Dos on the Day You Show Your House
Don’t risk losing buyers because of little things you overlook. Check these off your list before you open the front door
Full StoryBEDROOMSMaster Bedroom Suite Pairs Wood and Marble
A London home’s master bedroom and bathroom reconstruction pays careful attention to materials and features
Full StoryDECORATING GUIDESThe Hottest Home Design Trends From Around the World
Bold, elegant and sustainable — we review the six biggest trends from 2019’s major design fairs
Full StoryKITCHEN DESIGNHouzz Call: Tell Us About Your First Kitchen
Great or godforsaken? Ragtag or refined? We want to hear about your younger self’s cooking space
Full StoryHOUSEKEEPINGCan-Do Cleaning Strategies for Busy People
While you dream of having a maid (to go with the cook and chauffer), this simplified cleaning routine can keep your real-world home tidy
Full Story
Zalco/bring back Sophie!