"Question: can this hole be fixed so that it will be totally unnoticeable?" Claude-007: You will always be able to find this repair, even if I fixed it and I have an Invicon kit. As I have mentioned in another thread, when the homeowner screws up, my repairs look fantastic, when the contractor does, not so much. The standard you should set is this: "Would a professional home inspector readily find this repair?" If the answer is no, it's successful, if yes, maybe not. I mistakenly drilled some holes on my nephew's new dresser drawers. We bought some flat stainless steel plugs that went perfectly with his pulls to fill the holes. It looked great. Sometimes a contrast is better. How about some pictures? One up close and one farther away.

Hi, Latches that don't reach the hole in the strike can be fixed by filing the hole bigger. Sometimes the strike plate has been painted often enough to have closed the hole in, so by removing the paint buildup, the problem is solved. The latch itself may be bent, which can be fixed by taking the lock out of the door (if it is a mortise lock) opening the case, and taking out the latch. It can then be straightened with a hammer or pliers. Hinges can wear out, allowing the door to move downward (often seen on bathroom or exterior doors where excessive moisture promotes rust) Hinge screws can loosen, allowing the door to sag away from the strike. Occasionally the settling has moved the meeting points too far apart for filing- in that event, the strike plate can be moved. I hope these suggestions give you someplace to start analyzing the problem. Casey

Hi everybody! I have been waiting all summer for it to cool off. It seems that the heat makes my dizziness and nausea worse. I have lost about 15 lbs with being too sick to eat throughout the summer. I just this week got my helper here to help me clean the garage and then I moved the vanity out there and sanded it a bit in the easy places, and got it up on a table. I got the brass floor protectors pried off the bottom of the legs and was pleased to find no holes have been drilled in them. That means that I can drill holes for the feet I bought. I have adjustable feet that will give the vanity an extra 1/2" of height, and that can be screwed up to give another 1/2" if we want. That would make the legs appear to float way too high in the air, so I don't think it will work. the extra 1/2" will have to suffice, with the ability to make the vanity level so that the sink will drain properly. I have also decided that the bail-type handles that came with it are not going to work for us. I can't see us fumbling around trying to grab the bail that has recessed back into the grooves of the handle around it, standing there with water or soap in our eyes. A knob is much easier to use. I had Hubby try using the bail and he vetoed it on the first try and said, "replace 'em!" I am using these on doors of a set of shallow cupboards that will be recessed into the closet of the the neighboring bedroom. I figured they were a sure bet for the six drawers, too. I am not going to use the center drawer anymore, what with all the plumbing going on above it, so I will just fill in those holes. I need to cut away the bottom of the drawer space, then move the drawer support piece to the left or right. It is at dead center right now, and the sink's drain will need to go there. I just have to sand down the fluted areas of the vanity table, then it will be ready to be primed and painted. I am still leaning toward painting it the violet Peace and Happiness. I have purchased more components for the plumbing. I have all of the shower controls and the rain shower head and regular shower head. Still need to get the hand-held and some safety hand-hold bars for the shower area. I still have not finalized a wall tile (looking at fake Cararra tile for the room's walls) or floor tile or the surface for the top of the vanity. We HAVE concluded, though, that we cannot get this job done until Toby, our ever-more-confused beagle/golden retriever mix, dies. He will be 16 at the end of this month. He has spinal arthritis and began vomiting every time he was given his Tramadol or his glucosamine/chondroitin pills, then quit taking them. He had to go on prednisone to control the pain. He is peeing a lot in the house, always on a rug or quilted mattress pad put down for him. The bathroom is his main place to pee. I will not have my new floor grout saturated with dog pee. I don't think the poor guy would cope well with the construction, either. He is now blind in one eye and somewhat deaf. It would be too confusing for him to do all that construction. So even though I can't get Jim over here to do the work, if I could, I would not be able to do it until Toby passes on. So, instead, we are getting new gutters and trim, and getting our four remaining windows replaced. We did the other three windows when we remodeled the kitchen and made the living room into the library/music room. I am in the process of cleaning and decluttering so the window guys can get in to measure!

I got the cabinets through Home Depot (20% off) they are not higher end but they have held up extremely well and we’ve been happy with them. I don’t remember the brand, but the color is cognac on maple. They’re standard kitchen cabinets. We got 2 regular drawer banks, 1 extra wide drawer bank, 2 sink cabinets and the closet you can see in the picture for about 1800 w/the discount. We bumped the shower wall 6 inches into the bedroom to make the shower bigger, pulled the cabinets out from the wall a couple of inches to provide more counter top. And curved the edge the counter for interest. Just for fun, this is what we had to start with. The tub was rusted and there were two doors, 1 from the hall & 1 from the master bedroom, we closed up the hall door. I think we got our moneys worth. LOL As for the labor, I found my Contractor through a plumber I had hired to put in a kitchen faucet. I asked if he had someone good he could refer and he referred Matt to me. Matt had his own company but just him and his guys. All of his work was by word of mouth, he didn’t advertise or push for business, he didn’t need to. I think I got fair pricing from him because he didn’t have the overhead a lot of the larger companies might have. He wasn’t the least expensive and he wasn’t the most expensive. Finding someone who was willing to work on our schedule and not having to have it done ASAP is what really helped me to be able to keep our costs at a minium for both labor and materials.