In case Jenn gets notifications on this thread, I have a similar problem. I wanted to use sconces but think there is not enough room so I think we might need to use a bathroom bar. How is the lighting you are receiving from the lighting? Are the shadows impossible? Troubling? Minimal? Thanks...should you see this.

I think consistency is important, especially in a small space. If most of the finishes are chrome (what's your hardware on the vanity, by the way?), by installing a light or lights that are ORB, you are drawing attention to them and you might want to think about that. Seems like from what I've seen on the shows where people are fixing up to sell, keeping things neutral is a good way to go. And just because you can see the two lights from the LR, doesn't mean they should match; the lav and the LR are very distinct spaces, after all. If you feel its too cold in there with all chrome, perhaps warm up the space with a nice pop of color in your hand towel, mat on the floor if you are so inclined, or other small accessory. Good luck!

We are in the midst of a remodel and the framers have already started!! We have an existing bathroom (approx. 5x8) for which we are opening a doorway for direct access to a bedroom. We want to retain access to this bathroom from the hallway, so we are installing a pocket door. It is an older home and I have a 32" x 68" door that matches the existing doors to use for the pocket door. It is heavy, solid wood. The contractor is going to use Johnson Hardware for the framing (am waiting on more detail for the hardware). It is being installed in 2"x 4" pocket (no room for anything larger). This is our forever home, so we would like for everything to last for 30 more years :-). Some questions: 1. As mentioned, the door is heavy. I read on a forum somewhere that a contractor had used the Johnson Hardware for the framing, but had used the glides on the bottom from Hafele. Has anyone else tried this or have any suggestions? 2. I'm not certain as to how smoothly/easily the door will glide once installed. We have two other pocket doors to the house, but they are over 50 years old and take a small amount of effort to pull closed. This will be my daughters bathroom and she is 8. Should I install soft close on either end of the pocket door (wondering about little fingers getting smushed or door closing into the pocket too quickly)? Has anyone used these? I've seen the videos and not sure it would be more frustrating for kids to have the soft close. 3. Instead of using the pulls on the 1 3/8" side of the door, has anyone ever installed a bar handle for a privacy/bathroom door on the "outside" of the door, or would this be too odd (our house is more traditional than modern)? I thought this would be easier for kids to operate...but I can't find any pics online except for exterior or non-privacy doors. I did find the picture below...not sure I've posted it correctly from Houzz. The door would also need a lock...see question 4 below. <div><a href='https://www.houzz.com/photos/gb-honed-range-projects-contemporary-bathroom-brisbane-phvw-vp~10854162' target='_blank'><img src='http://st.hzcdn.com/simgs/50112acb03431552_3-4391/contemporary-bathroom.jpg' alt='GB Honed Range Projects' border=0 width='214' height='320' nopin='nopin' /></a></div><div style='color:#444;'><small><a style="text-decoration:none;color:#444;" href="http://www.houzz.com/pro/australmasonry/austral-masonry" target="_blank">Photo by Austral Masonry</a> - <a style="text-decoration:none;color:#444;" href="https://www.houzz.com/photos/contemporary-bathroom-ideas-phbr1-bp~t_712~s_2103" target="_blank">More contemporary bathroom ideas</a></small></div> 4. Because the door has been used as a swing door, there is a round hole where the knob would be. I understand that there are blanks that can be used to fill the hole and be sanded and painted. I anticipate that most of the time the door will be closed to the hallway - so very visible. Should I use a round privacy lock for the door (I was looking at the Linnea line) to use instead of trying to fill the hole? Would this look strange with a bar handle as mentioned above? 5. Other option could be to flip the door around so that the hole side is the side that recedes into the pocket wall (though plug would still be visible) and install a mortise kit like the Emtek and forgo the bar handle altogether. 5. Because this is a privacy door, I'm having the frame of the door jamb have a "lip" on both sides that the pocket door will slide into to lock so that there is no slight crack at the opening...no question but is there anything else we may not have thought of? Any advice would be MUCH appreciated!

I had the exact same problem. I picked out the vanity I wanted but did not think about the fact that it wasn't made to sit flush against the wall. I spent a month looking for something else, but in the end we decided to go with something shorter and have it not be against the wall. But we were going from 72" to 60" which is probably not workable in your mom's situation. I did find a lot of vanities that did have flat sides and could work in a corner, if you are willing to have the countertop fabricated. They just need to not have any trim detail on the top or bottom like the one you picked out does. I would just look at the ones without the pre-made tops. Because the pre-made top will still leave you with a slight gap because of the countertop overhang. This is an example: Avanity Modero which is sold everywhere, not just at Lowe's. The cabinet we ended up buying is an Avanity Madison which won't work for you, but I assume it is of similar quality. We are pretty happy with it. The drawers and doors have soft close but I do feel like the glides in my Ikea kitchen drawers are better quality. It is very pretty and I wanted a stained wood so I am really happy with our choice. If I had been willing to go with a painted finish, I think we might have stuck with the 72" Modero.