We have an arch over our tub. Here are a couple of pictures:

Me, too! I've been looking at the Tea for Two, but I want a tile flange and I really need a tub that's 60"long x 30" wide, (not 32") and prefer 14"+ water depth (at least 12") and cast iron. I would love any suggestions people have in addition to the suggestions above, which didn't meet by specs for depth or are over-mount drop-ins (or similar). I would also like to comment on the above recommendations so people don't order the wrong thing. Most clawfoot tubs, including the ones mentioned above such as the Cheviot or Sunrise Specialty, have a water depth that is around 11" at most. They are comfortable, but not deep. The Cheviot alcove tub is an over-mount drop-in with a water depth of under 11". It would have a calk line around a drop off on the deck. Oh, heck no! The Toto is an over-mount drop-in also. Dang! The Waterworks Minna sounds promising, and it has an apron, but what's with that moulded raised ridge at the top? It makes it look like a top-mount drop-in and have similar problems. I guess you wouldn't need calking, but you'd have that ridge water could get over and a lump under your head if you lean back. Has anyone installed one and has pictures? I'd love to be proved wrong on this one in spite of the price! It could be the perfect tub for me if it weren't for that top detail.

"I could also just get a pull-down faucet for the sink and aim it at the tub to fill it." You could - but you won't like it. The most one of those will fill is 2.2 gallons a minute - some less that that. Divide your tub's capacity by that and you're looking at 20 minutes to fill +/- Not good. beekeeper - I have one of these and have placed more than half a dozen in projects over the past few years. What you get for your money is a machined brass body that mounts in the ceiling or wall and a plated trim piece. The body is a substantial piece of hardware and chrome,brass, nickel plating costs $$$ too. Whether that's all worth 500 + bucks, is up to you. Like davidro says, it doesn't matter what the delivery system is, this is just an opening for hot water to come out of, albeit one with a bit of engineering. GD & Spanish - the splashing is very much dependent on the mounting height of the unit AND the tub selected AND the location of the water column inside the tub. Mine hardly splashes at all. The ones I have seen that splash only do so for a minute or so until their is enough of a pool in the tub to counteract it. Flat bottom tubs with tall ceilings are going to splash more than one from 7' into a sloped contact point in the tub. Besides , we're talking water in a bathroom, generally tiled so what's the big deal ??? It's not like the amount of splash is the same as taking a shower and leaving the door open. 2. While you are correct in that "the water cools off much more than it would from just a regular tub filler", it's not as if it cools off enough for anyone without a thermometer to tell a difference, and a very sensitive one at that! Sure the air cools the water more from a stream falling from 8 feet than one falling from two feet. But bath water that is 100 + degrees is not going to cool down to 90 deg. in the xtra 1-2 seconds it takes it to fall from the ceiling- get real. Additionally , that filler produces a very dense column of water (laminar) that has little to no air in it, so one might argue it will be hotter and less prone to heat loss than a "regular" filler that introduces room temp air into it's stream - thus cooling it off on it's way to the tub. So don't worry Spanish -your tub will still be plenty hot with that filler if you choose it. IT'S A NON -ISSUE people. I've already alluded to the real issue for lower tub temps - FILL TIME. That's directly related to the delivery system ( valve). If your valve and accompanying filler will only deliver 5 gallons a minute it's going to take a while to fill an 80 gallon tub, and there will be some heat loss. Select a valve that delivers 20 gallons a minute and you can be soaking quicker that most people can undress. Here is a link that might be useful: laminar valve body - see page 2

@jewelisfabulous - ahh, so nice to have a window! I'd like to hang artwork, but I'd be a bit concerned it might fall and damage our new tub! @monicakm_gw - thank you taking the time to attach a photo. What a serene bath tub you have! You just gave me a great idea for the 3 walls that will be bare since we won't be tiling all the way up to the ceiling. A towel rack would look great on the back wall :) 1. Did you mean your tub is 19" in height (from the floor)? 2. If it's not too much trouble, I'd love to see what your faucet for the bath tub looks like!