I go with cloud_swift's idea. Although my eye is anal, so I'd have the line of 5-panel going straight across. There are drawers that are just too short to warrant the stiles and rails. Those, I'd go with slab. The larger drawers, where you could actually see the recessed panel, would be where I'd go 5-panel. It's the same with tall, skinny cabinets. 9" cabinets wouldn't show the detail! The rails and stiles would be right next to each other! The detail does show, even with darker cabinets. A pure slab is very much more modern -- unless they're inset. But you haven't mentioned which. As much as you talk about your handles and pulls, they're still going on a door or drawer. The detail behind them -- or lack thereof -- will change how the jewelery is showcased. I'd suggest just being consistent. Maybe all the top, skinny drawers slab, with the larger, lower drawers being detailed. You chose this because you liked it in the first place. Are you settling?

From the attached link: Raised Panel - Solid Even though the panel is called solid, it is not usually made of a single piece of wood. Wood expands and contracts with changes in humidity, and this can cause the door to split and crack. To counteract the problems of natural movement in a solid wood center panel, the panel is usually constructed using several pieces of solid stock lumber glued together. The wood strips used to construct the panel may not all match in graining and color. As in the case of the slab door, the door's strength comes from the manner in which the pieces of solid wood are reversed as they are glued. The panel is then cut on all four sides, so the center is higher than the edges. The face of the panel is usually flush with the front surface of the stiles and rails, with the edges forming a tongue which fits a corresponding groove cut into the door frame. The groove is slightly larger than the panel's edge to allow the panel to float in the frame. This simply means that the panel has room to expand and contract during humidity changes, reducing the risk of the panel cracking or splitting. I gather from the Woodmode site that this is how they construct raised panel doors as they describe their raised panel doors as being constructed from solid wood. How big an issue the movement of the centre panel in a flat panel door will be probably depends on geography (I have seen some dramatic examples here that am sure would not be acceptable to many folks while I tend to think the hairline cracking I have seen is part of the charm and patina of age of painted cabinetry. In terms of Woodmode they do kiln dry all their wood which may in part explain why they have not have felt they would get better performance from an MDF centre panel that some companies are opting for. I also think it is a market issue a lot of Consumer's in the US have a real aversion to composite wood products regardless of the possible benefits (this does not really carry over to Europe or Canada). Cabico and many other Quebec companies offer 100% MDF doors for paint finishes (same opaque finishes are usually available on maple at Cabico). Lots of their MDF door styles are raised panel. Here is a link that might be useful: Explanation of door styles

I finally have a couple pics of my flat panel door. Wish I had all of the doors, but alas... Anyway, in the pics, the minimal pattern does get a little lost in the walnut, but I would imagine if you did the same pattern in a lighter door it would stand out, even in photos. aimskitchen, you may also want to consider that there are two types of flat panel doors. The first truly is flat, and is usually made of mdf covered in veneers. I was actually quite surprised to see even high end cabinet lines using this kind. The other kind of flat panel, only appears to be a flat panel from the front. I believe it is actually called a recessed panel because it's sort of like a raised panel that has been flipped around. You can tell this kind because the back of the door will look something like this: Hopefully you can see in the photo that the panel is raised in the back. If you get a recessed panel you will have the look of a flat panel, but it will be solid wood and much thicker than a veneer flat panel.

Designov, I visited your post regarding your gorgeous new kitchen and due to the recessed doors that I love since I have been wanting the cabinets that you bought and the crown molding and the overall look, I felt it looked beautiful just the way it was with the matching end panels that were just not door style panels. I felt it looked pretty and finished and gorgeous. Thanks for sharing.