As others mentioned, I would either have them replace the piece or find a new faucet (at their cost maybe?). Since it is not a natural material, you won't be losing anything with a new piece. I would not be willing to live with something that looks like a retrofit just for a discount.

This old thread got revisited. @dani_m08 to answer the question about extra probe, I believe I ordered an extra one when I bought the set up. The probe wire is just setting in the junction box I think but honestly I cant remember. When I laid out the underfloor heating and the probe, I just ran another probe near the first probe, and it was then sealed into the floor self leveling compound as per instructions. then the end was just threaded into the wall like the one that would be live, and not connected, but just laying there in the box. Regarding the tile layout. I just decided to run it this way, after getting instructions on the 90Degree way, IIRC. The herringbone that I love is from my childhood and the side walks in my neighborhood that all ran at 45Degree. so that to me is herringbone. I know you posted on @sochi thread about her amazing bathroom and a wall mounted faucet. I would totally do it if I had the right sink for it. In my case I had made my sink out of soapstone and an integrated backsplash. The pictures of this bathroom reveal are no longer available because of the use of photo bucket, when it was Gardenweb. I did not keep my account with photo bucket. I'll add some of the reveal pictures so you can see the sink and floor. Regarding the sink there is no ledge for water to drip from my hands when using the faucet. The water drips right into the sink. In my other bathroom with a deck mounted faucet I am always wiping up drips and it is a nuisance. I much prefer the setup for this sink. Below: I love the flush finish from the faucet to the bottom of the sink. nothing drips on a counter or edge of a sink. Below: looking in from the doorway. Below: Here I am finishing up the sink. the backsplash was epoxied on as a separate piece. The whole soapstone install in the room took next to nothing to buy as they were all small pieces that I epoxied together with a 3 part stone epoxy. Below: this is the counter at the tub, and is in 2 long pieces but I was able to epoxy them together at there edges to make a wide slab for the top. All the soapstone was finished with a 60 grit sandpaper to be rough and this lovely soft tone of blue/green/gray/white. I did not oil it so this color tone would remain light. Below: If I recall correctly @sochi helped me decide on this Hubberton Forge Mirror. I have 3 different metals in this room, but they are all a cool silver to black color. Below: the center of this tower shares space with the kitchen on the other side of the wall. there is also some extra space that houses some electrical wiring. this is an old simple house. this bathroom was an add on when it got move to the farm in the 30s IIRC. The plumbing was all rearrange and some of the details that were orignially there I kept but updated it, such as this tower feature. The old one went and the carpenter did a wonderful job with this one. Below: This feature was another thing I kept from the old bathroom but flipped it from the other end and had the carpenter put drawers in it. Before it was a hell hole. things got lost and the build was soooo old and creapy I didn't like using it for storage. Now it is perfect for storage.

I'm planning on doing this in the next few months. Have had the sink picked out for a couple of years! Wanted to put two faucets in the wall, but husband is adamantly against it. So I guess I will make do with them mounted in the countertop. I see some nice ones online. The sink is about 30" wide, and has no faucet holes. Cabinet is 54", and there is no room for anything larger. I think we can do with about a foot of counter space each on either side. Better than one small sink/faucet. Frankly, I think it will be a huge improvement, even for resale. Even undermount oval sinks would take up about 20" each, leaving only 14" for the space between, and the spaces on either side. I think that would look ridiculous. :)

This was originally a lake cabin (1966) about 850 sf. According to tax records it slowly "grew" until it is now about 3500 sf. They did not remove old roofs as they enlarged the house. This bathroom is part of the oldest section of the house. That means a roof over a roof..so no way to put in a skylight. I am not happy about it, but nothing I can do. The bar fixtures we just removed made it bright enough, but they were old. 5 bulbs on one wall and 4 bulbs on the other. I think if I buy lights that can take 100 watt bulbs, and if I have two lights on each side of the mirror or 4 above the mirror, then it should be enough. I hope. I haven't seen any lights that take 100 watt bulbs lately though or led equivalent of 100 watt. Maybe with the incandescent bulb issues a few years ago, they quit making those 100 watt fixtures? So, in a couple of years, we plan to sell the house, so I want nice looking lights, but not expensive lights. Something classic, not trendy. I am spending a small fortune on a solid surface shower, stone countertops, and custom cabinets. We gutted everything but the ceiling, and that popcorn junk will be removed. We are going to try to save the marble floor. It should work well. Black marble floor with white veins, either white or light gray swirl for shower base, either subway tile or solid surface walls, light gray quartzite or marble countertops, and medium oak cabinets. Paint color will be last, but I need to preplan for the lights' location to have it wired correctly before we put up sheetrock. Will I get more illumination if I put two lights on either side of the mirror vs above the mirror? Thanks