I currently have a smooth top glass range. Every time I saute with olive oil (a frequent occurrence), after I'm done, no matter how careful I have been, whether the food being sauteed is at room temp. and/or dried as much as possible, in a perfectly good, appropriately-sized all-clad pan or any other I've tried, I have splatter on my cooktop and the control panel (in the rear of the cooking surface). If you are able to avoid this, I'd love to know how. This is one of the many things that pushed me to induction, which can be protected during cooking, or, at the least, stays cool so that it can be cleaned immediately and will never cook on. And I don't care for spatter guards, as I find it seems to have a steaming effect on my food, and I have to lift it in any case to stir, at which time the afore-mentioned spattering occurs anyway. It was Trevor Lawson, at Euro Stoves, who talked to us a long time about ventilation needs when we were considering the Blue Star, so hopefully he can help you. I hope you will keep us posted on your solutions, and, certainly post pics when it's done, since it's such an unusual configuration.

I have only seen this on a previous project in NJ. The other buildings with this system would not even allow vent hoods to use the system due to fears of grease build up. I don't know that there is a "CFM" that you will experience, but the working system I saw did NOT perform particularly well. For a normal cook it was adequate at best, for someone doing high heat/smoke/grease cooking (wok, frying etc) it was not nearly effective enough.

If the cooktop or range is against a wall, then the amount that the hood aperture extends past the burners front-to-back should be commensurate with the amount the hood overlaps the burners side-to-side. This is because the rising effluent expands equally in all directions as it rises. (A powerful hood will cause some distortion, but nominally and for the most part practically, the hood air flow does not "reach out" and suck in air that already has a velocity that dominates the air velocity of the hood intake air away from the actual aperture.) The best insertion of make-up air (MUA) is any method that doesn't cause any cross-drafts at the hood. In test kitchens, this is done by introducing MUA through porous walls. We can generally exclude this approach for residential kitchens. Floor, wall, or ceiling registers (diffusers are what you want for air flowing out, but are not really suitable for floors) are all potentially suitable options. Mine is a ceiling diffuser located down a hall that leads to the kitchen. This provides some flow straightening and area expansion as a means to minimize cross drafts. Cost of heating MUA is not high, but the assembly of parts needed may be high in cost. Unless you operate your hood 24/7 boiling off maple sap, you likely will only be running the hood at partial to full power for short durations. I have a heat exchanger hooked to my hydronic heating furnace that can utilize all of its (forget the exact number) probably 180 kBTU/hr output if needed for MUA heating. I think the furnace at this rate uses 1 point something gallons of oil per hour, so this high cost is around a few dollars an hour for usually less than an hour when the exterior temperature requires the maximum temperature correction. In any case, I believe that an electric heater in the MUA path will be an easier thing to integrate. Cost per hour may be higher in proportion to your electric rate's higher cost (per BTU) over oil. You may have to run significant power from breaker box to heater if you are going to make-up very high flow rates through the hood at -20F. (Fireplaces can have high flow rates that have to be made up also, but I don't know anything relevant about the flow rates of gas fired fire places, so that should be something you can find out for planning purposes.) If you are rugged enough, the MUA heating doesn't need to be perfect in temperature control, just good enough to keep the introduced air tolerable during the cooking. Your code requirement doesn't provide for different conditions needed for safety, it just mandates MUA. The safety requirement that should be driving a more sophisticated MUA requirement, applicable where combustion appliances are used without their own separate MUA sources (ducts to outside, operation in a closed room ventilated to outside, or whatever), is to keep the internal house air pressure high enough to not back-draft the appliances, and thus avoid pulling carbon monoxide into the house. For unblown gas appliances, the house negative pressure limit is 0.03 inches of water pressure, and requires very low pressure loss in the MUA system with a powerful hood. I think this is necessary for fireplaces also, as they depend on the draft for flow, and the draft depends on the pressure difference between hearth and top of chimney, given hot flames to provide upward momentum. All this means is that you can either provide a code-compliant MUA system that is rated for a given flow rate, and for safety do whatever is really needed to safety proof your combustion sources, or provide an MUA that is sophisticated enough to keep the house pressure up over the range of ventilation flow rates possible with the hood, fireplace use (potentially high flow rates themselves), bathroom fans, etc. While I am working toward a closed-loop pressure controlling MUA system for myself, I am certain that for most needing MUA, isolating appliances is the better cost approach, allowing the MUA to aid hood blower performance, and not be so critical for safety. My oil burning furnace does have its own MUA, but I wouldn't operate my fireplace with my kitchen ventilation running at full power, even with windows open (due to pressure loss in the screening), without a powered MUA path. Can't help with an educated HVAC company, but FanTech has a line of powered MUA systems (don't recall if they are heated). If not, a suitable heater can be found and inserted into the duct path. Someone on this forum back in the 2008 to 2010 period, possibly clinresga, provided an image of his basement ducting with coil electric heater in the path. My [not yet completed] system is in my attic and draws air from above the roof. A blower will push this air through a filter, through the heat exchanger (think car radiator), and into the diffuser. HVAC companies dealing with restaurants will understand what you have to do, but often their setups are not compensating -- flowing a fixed MUA flow rate against fixed vent hood flow rates. Large building MUA is usually compensated, but the schemes used are better suited (as far as I've been able to learn any details) for continuous pressurizing MUA systems that have to compensate for outside door openings. They can do this with passive air pressure control of dampers that recirculate MUA around the blower. The blower motor runs continuously. The relatively recent of introduction of residential MUA requirements has provided some impetus to development of residential MUA systems, so availability of systems and components should be expected to increase. Keep reading; be sure to check out the Greenheck paper available at their website: KVSApplDesign_catalog.pdf, as well as CKV_Design_Guide_2_031504.pdf, available somewhere on the Internet. These are commercially oriented, but should provide useful insight. kas

I am the resident expert only because real HVAC systems engineers don't frequent this forum, as far as I know. Noise introduced into the kitchen will be significantly reduced if an external blower with silencer can be fitted. A lot of the high frequency blade tip turbulence caused noise will be removed. This is also true of an in-line (duct mounted) blower. The issue of the neighbor is difficult to assess. What is the configuration of his or her windows relative to your potential external blower (1500 CFM I assume you meant). Your own window sound transmission is also an unknown. Generally, the external noise could be abated by (a) using a silencer on each side of a duct mounted in-line blower, or (b), using a deliberately under-driven* "up-blast" commercial blower (mounted as a side blast). (I think opaone is using an under-driven blower for his new system.) It is also possible to use a chase to move the blower up to roof level. I have a 1500 CFM nominal Wolf (Broan) blower on my roof. Its sound level is detectable but not obtrusive from the ground, but it might be if in a wall location where the sound is "trapped" between two houses. Possibly a more expensive but similar in design Abbaka downslope unit would be marginally quieter. ------ * commercial blowers of this type can use a pulley system between motor and fan that allows for different ratios. By choosing a ratio that operates the fan blades below their rated speed when the motor is receiving maximum voltage, significant turbulence noise can be avoided. The physical cost is a larger unit than would otherwise be required for the desired flow rate. Residential blower fans are directly coupled to their motors.