All I see here is a message that says "Bandwidth Exceeded". I never got to see the photos.

Posted by canarybird (My Page) on Wed, Aug 19, 09 at 16:21 Food Photo Tips Part 7: Macro, Closeups & Camera Icons Hi again everyone. I'm back with another entry on how to use your digital camera for taking tabletop photos. Today I want to again go over shooting closeups or macro photos, as well as explaining the use of some of those icons on your camera. Icons for MACRO and SUPERMACRO The term macro when used with photography refers to making small objects look larger through the lens of your camera. Point and Shoot cameras have a normal focal range within which objects are in focus, that is, the camera is able to see your subject clearly and record a sharp image. However if you get too close to something the camera is no longer able to focus. By using the MACRO function on your camera you are able to get a closer shot . You may have found that when you try to get a closeup picture of something on a table or even a closeup of a flower, the result is blurred, even though you braced the camera on the table or used a tripod and had enough light. Depending on your camera you were perhaps too close to the object for the camera to be able to successfully focus. Many digital cameras have a flashing focus light which you can see in a corner of the viewfinder or on the LCD screen to warn you that the camera could not focus properly while you attempted to take a closeup photo. You have to then move backward a little or switch on your MACRO mode. Remember that you should always press the shutter button half way to let the camera focus on your subject before pressing it fully. If the light begins to flash as you do that halfway press, then you know the photo will be out of focus unless you change something. Either move further away or turn on your MACRO setting, press halfway again and your focus lamp (that light in the screen corner that flashes) should stop flashing. It should stay fixed and give a little beep to tell you that it now has the subject in focus and you can finish pressing the shutter. Note: don't confuse the FOCUS light with the FLASH symbol because they can both blink. The flash symbol is a red thunderbolt, which if blinking, indicates there is not enough light to take an optimum photo. Examples of using PORTRAIT mode without MACRO when camera was too close to be within focal range, and then the same setup using PORTRAIT and MACRO mode. Some cameras have SUPER MACRO which allows you to get very close to your subject, where in some cases the camera can be placed less than an inch away from the subject. I'll show some examples: Coins in PORTRAIT mode without macro, then with MACRO, then with SUPER MACRO. Here are a couple of cameras owned by forum members with their focal ranges (distances at which things will be in focus.) The Kodak Easy Share DX 6490 - this camera will focus normally from infinity down to 2 feet away from the subject. If you want to get closer than 2 feet to that piece of blueberry shortcake, you will have to turn on your MACRO mode (it may also be termed CLOSEUP mode). The macro mode on this camera will focus from 2.3 feet down to 4.8 inches. So you should get a sharp picture within that range. Canon Powershot SD880 IS - another member's camera. This one can get as close as 1.6 ft in a normal mode setting. Closer than that and you have to turn on your MACRO mode which has a focal range of 1.6 feet down to 0.8". That means you could put the camera a little less than one inch away from your subject. That would be too close for food photography but you can try it at a distance of 1.6 feet and see how it turns out. On my Olympus SP560 UZ the macro and normal settings have the same focal ranges, which is 3.9" to infinity (10 cm to infinity.) So when I want to get really close I use the SUPER MACRO setting which gets as close as 0.4" (less than a 1/2 inch). Good for insects, flowers or miniature items. On the little pocket-size Olympus Stylus 800, the normal focal range is from infinity down to 19.7 inches. If I want to get closer than 19.7 inches to my subject, I have to turn on MACRO mode, which is good down to about 8 inches away. Closer than than I would switch on SUPER MACRO if it were appropriate for the photo. Examples with this pocket camera are the photos of eggs,above. You should be able to use macro in several of your cameras SCENE settings appropriate for a closeup photo , such as PORTRAIT, INDOOR, CANDLE, DOCUMENTS, AVAILABLE LIGHT, CUISINE, but not in pictures where distance is a necessary factor in the photo. (Landscape, landscape and portrait, fireworks, sunsets etc.) Try setting your camera to PORTRAIT mode and prepare a plate of fruit or other food. Set the WHITE BALANCE (WB) and if not during daylight, to the type of lighting you have. If the picture through the viewfinder (or LCD screen) looks dark, then use the EXPOSURE COMPENSATION (EV) button to get a plus factor until the picture through the viewfinder looks good. Take a picture. Then holding the camera in the same position (or with your tripod) switch on the same options plus the MACRO (or closeup) mode. Take the photo again and compare the two. Or better still, take several because its a fact that the more you practise and the more photos you take, the better they will become. If you continually experience blurry photos it might be a good idea to check out your normal focal range in your (shudder) manual under specifications, Macro Mode Shooting", or go online to *one of the websites that does reviews* and look at the specs for your camera model. There you will see the normal focal range (it may be called shooting range or macro/close-up mode) as well as the MACRO range. *A couple of good websites for checking out details of your camera are: Steves Digicams as well as DP Review. But the easy way to check it out is to get close to your subject, half press the shutter and if the focus light blinks, move back and repeat pressing the shutter until you find a distance where the light no longer blinks. That will be the focal limit of your normal range. Closer than that you will need to switch on MACRO. Other reasons for blurry photos are: 1. Not enough light. The camera needs more time to focus in low light and during that time you or the subject have moved. Use a tripod. This is true especially for indoor or evening photos, and when using night scene options on your mode dial. 2. Camera shake. Even though you have strong light your photos are still blurry. You are moving the camera or your subject is moving. Dont move the camera when you press the shutter button. Hold arms tightly to your sides, brace yourself against a wall, rest the camera on a solid object or use a tripod. If necessary, breath out and hold it while you press the shutter! (Remember to breath in again please.) Leaving MACRO for now, I wanted to go over the BUTTON OPERATIONS and THE MODE DIAL to briefly go over what some of those icons mean and what will they do when you click them into action. Heres a typical MODE DIAL, found on the top right of a digital camera When you turn this dial and select a mode, you are telling the camera to change the settings for a certain situation. Some cameras will have some of these icons together on a separate mode entitled SCENE or SCN on the mode dial. Typical mode choices found on the top of a modern camera dial are for :MOVIE, AUTO, CHECK PICTURES (Review), GUIDE, MY MODE, and M, S, A, P for choosing MANUAL, SHUTTER PRIORITY, APERTURE PRIORITY and PROGRAM. The photo shows icons for an older digital camera where some of the scene options were included there rather than in an in-camera menu. Heres what they mean: AUTO The simplest of all shooting modes, the settings are fully automatic. The camera selects what it deems to be the optimum focus and exposure for your still picture. PORTRAIT - suitable for taking a portrait style photo; the camera sets a wider aperture (lens opening) to blur the background a little, so the subject stands out clearly from the background. SPORTS - suitable for fast action shots, in this mode, the camera sets a faster shutter speed to catch moving objects such as people in sports events. LANDSCAPE & PORTRAIT the camera sets the optimal shooting conditions for a background scene with a subject in the foreground. LANDSCAPE the camera will use a small aperture (lens opening) to be sure the whole of the photo will be in focus, from foreground to background. This is the opposite setting to PORTRAIT where the background is deliberately blurred. Blues and greens are enhanced in this setting. NIGHT this is where you will need a tripod because the camera will use a slow shutter speed, meaning that any movement while the shutter is open will create a blurry photo. You can have some interesting results with coloured lights and portraits in night scenes. Do play around with this mode and see what comes out from your inventiveness. SELF PORTRAIT hold the camera at arms length and turn it toward you to take a photo of yourself. A fun mode. MOVIES the camera sets aperture and shutter speed for optimum results for taking movies. You may have to click on the microphone icon in one of your menus to include sound. MY MODE perhaps not seen on all cameras, this mode allows you to save a group of settings of your choice which can be recalled together with one click. PLAYBACK MODE allows you to go back and see the photos youve just taken. APERTURE PRIORITY also seen as AV on a mode dial. This setting lets you set the aperture setting manually while the camera chooses the appropriate shutter speed for that aperture (lens opening). SHUTTER PRIORITY also seen as Tv on a mode dial. This setting lets you choose the shutter speed manually while the camera chooses the appropriate aperture for that shutter speed. These two above settings are semi-automatic in that you have control over one or the other function. For example if you want to photograph sports and you know you need a fast shutter speed and dont want to rely on the automatic sports mode, then you would use the SHUTTER PRIORITY setting and let the camera choose the appropriate aperture. If you want to set a certain aperture setting but let the camera figure out the shutter speed then you would choose APERTURE PRIORITY. You can control the DEPTH OF FIELD, or the blurriness of the background where you want the background to recede and a subject in the foreground to stand out sharply by using a wide aperture setting. We could perhaps go in the next tutorial or so a little into DEPTH OF FIELD because I think many folks would like to learn how to get that beautiful effect of a single flower or piece of cake (!) standing sharply against a dreamy blurred background. PROGRAM MODE With just a little more freedom to be creative than the AUTO mode, here the camera sets both the shutter speed and the aperture, allowing you to adjust other functions such as white balance, ISO. I think this has been very long today so although we havent got much more to cover in the next two or three tutorials (I thought wed finish with ten all together), I think next time Ill go over the FLASH icon and FLASH menu as well as the SELF-TIMER option which lets you jump into your photos. Subjects Id like to mention: Depth of Field and how to make those beautiful Blurry Backgrounds, the important triangle of variables that you need to know: APERTURE, SHUTTER SPEED and ISO, how they work together and how to adjust them..or at least understand what is happening. And oh yes.I have to finish that full sized LIGHT BOX so we can see what results we can get from that! I hope you are understanding it all and if you have questions please ask here or PM me. So thanks for joining me. I'll be uploading the next installment soon. And please feel free to save the pages on your computer. Sharon (Canarybird) :-) (All text and photos copyrighted) Free for personal, non-commercial use Follow-Up Postings: o RE: Food Photo Tips: Part 7 - Macro & Camera Icons clip this post email this post what is this? see most clipped and recent clippings * Posted by coconut-nj (My Page) on Mon, Aug 24, 09 at 8:38 Sharon, while I haven't been posting directly to your photo tip threads, I've been following them avidly. I so appreciate all the effort you've gone to to explain in such an easy way so many aspects of taking good [better for some of us] pictures. The last week or so I've been very busy organizing and then hosting our family reunion at a local fancy diner and have not had a real chance to digest the latest installments. The macro stuff interests me very much. I've tried to use my macro recently and found when I did the camera refused to take the picture?? Odd. LOL.. I'll figure it out but I suspect I'll have to dig through the manual to see what the problem is. Your post makes me suspect it has something to do with the camera not being able to focus on what I'm trying to do or the distance, or something..heh.. and it won't fire as self preservation. Smiles. I'll figure it out and then be back to digest more of your post. Btw, I got a tripod for my birthday! Yay.. I relative I had staying with me for a while apparently absconded with my last tripod. Grrrr... Needless to say I'm looking forward to using the tripod to work on some of your 'lessons'. Thanks for all your great work on our behalf. o RE: Food Photo Tips: Part 7 - Macro & Camera Icons clip this post email this post what is this? see most clipped and recent clippings * Posted by canarybird (My Page) on Mon, Aug 24, 09 at 10:58 Thank you coconut, and good that you have a tripod now. I'm wondering what mode or scene you are using on your camera when you add in the macro factor. Are you in AUTO or PORTRAIT (closeup) mode? If you are in a scene mode such as landscape for example, you can't use macro as well because you would sending two different messages to the camera...a landscape or far away mode such as sport or sunset and macro, a very closeup mode. The other thing, if you are in PORTRAIT mode and adding in macro, the camera should take the picture unless you are too near your subject or it is too dark. Does you focus lamp blink (the dot in the corner of your screen) before the camera refuses to take the photo? If so, that tells you that the camera can't focus at the distance you are from your subject. Move back a little and keep pressing the shutter button half way several times until the blinking stops. Then take the picture. Let me know if that works and if not I'll think of something else. Luck....:-) SharonCb o RE: Food Photo Tips: Part 7 - Macro & Camera Icons clip this post email this post what is this? see most clipped and recent clippings * Posted by coconut-nj (My Page) on Wed, Aug 26, 09 at 1:13 Good points Sharon, I'll check it out. I thought I had been in food mode, but maybe not. Also the lack of light is quite possible, I'll check that out too. Thanks. Smiles. o RE: Food Photo Tips: Part 7 - Macro & Camera Icons clip this post email this post what is this? see most clipped and recent clippings * Posted by antiquesilver (My Page) on Sun, Aug 30, 09 at 1:42 I don't remember if it's this lesson or another that you suggested using the Self Portrait Timer setting with a tripod to avoid camera shake. So simple & yet so effective. The tripod part is standard but I don't remember being advised about using a timer before but it certainly makes a difference on inside shots. o RE: Food Photo Tips: Part 7 - Macro & Camera Icons clip this post email this post what is this? see most clipped and recent clippings * Posted by canarybird (My Page) on Sun, Aug 30, 09 at 5:57 Right on track antique silver. I'm going over the self-timer in the next entry, hope to have it ready for Wednesday for those who have never tried out using that feature on their camera, along with setting up the tripod and some tips on that. The self timer avoids any shake you might cause to the camera when you press the shutter button. A shutter cable release is another inexpensive addition which permits you to press the shutter without disturbing the camera body. Both systems will help you to eliminate blur caused by camera shake. SharonCb o RE: Food Photo Tips: Part 7 - Macro & Camera Icons clip this post email this post what is this? see most clipped and recent clippings * Posted by dirtgirl07 (My Page) on Sun, Nov 1, 09 at 13:54 Hi Sharon, I feel a little guilty not posting about food!! I have a question that you might be able to answer. I'm trying to take photos of miniature paintings (2.5x3.5in) and the varnish creates a major shine on them. Do you think your mini light box and macro would work on these? The shine is similar to that you get off of jewelry and silver. We've even tried scanning them in which does reduce that glare, but not completely. Thanks for any help! Beth o RE: Food Photo Tips: Part 7 - Macro & Camera Icons clip this post email this post what is this? see most clipped and recent clippings * Posted by canarybird (My Page) on Sun, Nov 1, 09 at 17:28 Hi Beth.... If you're taking closeup shots of miniatures you should be in macro mode. Reflection is always a problem with shiny objects. The light box would be fine as long as you can diffuse the light source by using white tissue or drafting paper and can change the camera angle as well as moving the objects around until the reflected light is not bouncing up into the camera. It will take quite a bit of juggling around to get the angle where you don't see the reflection, but diffusion is just as important. Good luck! SharonCb o RE: Food Photo Tips: Part 7 - Macro & Camera Icons clip this post email this post what is this? see most clipped and recent clippings * Posted by dirtgirl07 (My Page) on Sun, Nov 1, 09 at 18:44 Thanks Sharon! I guess it's going to be an experiment. After posting the question I realized that these were not 3 dimensional either - but flat surface.. That was going to be a challenge on the surface glare. They have to be photographed straight on. The scanned version may have to do, but it doesn't pick up the detail well. Thank you for your posts on the photography - those were great. Your photos are all wonderful looking and after seeing them and a lot of gorgeous blogs, you must have trained a LOT of people. Makes looking at all that food delicious!! Beth

Posted by canarybird (My Page) on Tue, Aug 25, 09 at 18:11 Depth of Field Hi again everyone. I'm back with another entry on how to use your digital camera for taking tabletop photos. Today I want to talk about Depth of Field. Depth of field is the area of your picture, from foreground to background, that is IN FOCUS. Here, in the first picture (left) you see the two pieces of fruit clearly because they are in focus. The background is out of focus, or blurred. This is a technique used to emphasize a subject and make it stand out from the background. Here again is another example in this sports photo (right), where the player in the foreground is in sharp focus against a blurred background. (Sport photo credit at right to Allen Eyestone/The Palm Beach Post) You will also see depth of field referred to as DOF in photography texts. In these next examples, the first mug (left pic) is the only one in focus and the rest are progressively more blurred. We can say that in this photo there is a SHALLOW DEPTH OF FIELD because the area that is sharp extends only to the first mug, in the immediate foreground. In the photo above right, there is a DEEPER DEPTH OF FIELD where most of the mugs are in focus. Sometimes you will want to have the whole of your photo sharply in focus (eg. landscapes, holiday pics or full dining table), and other times, such as in some food photos, you may want to have your subject stand sharply against what is only a suggested background, misty or shadowed to give an impression of what's there without detracting from your subject. Although creating a very shallow depth of field can be done beautifully with DSLR (digital single lens reflex) cameras, due to the lenses available for them, (you change the lens according to the type of photography you want to do), it's possible to get an attractive blurred effect with a simple point and shoot, such as the left picture of the mugs above. (I think in future I will call them P & S cameras, as it sounds better and is easier to write). Just to digress and show you what I mean about the possibilities of the DSLR, here below is the same subject taken by a DSLR at left and with a P & S right. You will have seen such extreme shallow depth of field on many food blogs on the web. In this case you see both the foreground and background out of focus, while the second row of the left egg and the right ceramic chicken are relatively in focus. To the right, the P & S version shows nearly all in focus except the chicken in the rear. I deliberately used a very shallow depth of field on the DSLR to demonstrate that a middle plane can be also chosen as the in-focus area. (50 mm Canon lens at f/1.4). So how do you get your foreground sharply in focus and the background out of focus? Here is one way to do it. Let's make a test run during daylight. Find your best window light with a table or shelf underneath and get some fruit, eggs, muffins on a plate or whatever you want to use as a subject, preferrably an object with a little height. Even a couple of coffee mugs will do. Take some other larger objects which could be pots and pans, a plate of fruit, a vase of bushy greenery or even a stack of books. Set your table so the pots, books or whatever are about 20 inches (50 cms) away from your subject (fruit, muffins etc.). Here's my setup for the first photo on this page...the prickly pear and kiwi pic at top left. I sat on the low stool and rested my forearms on the edge of the table, holding the camera. See if you can somehow duplicate this setup and sit low down enough to be able to have the camera just above table level and close to the subject. Set your SCENE or MODE dial to PORTRAIT. Why do I use portrait mode so much on these examples? The reason is that portrait mode is a medium closeup setting, meant for taking photos of someone about 6 feet away in front of you, rather than of a distant landscape. Therefore the aperture (lens opening) is wider than it is for distant shots. (Explanation about aperture later.) When the camera lens is wide open, the depth of field is shallow, which will make foreground objects sharp and background objects unsharp. So that a person in a portrait will stand out more against an out of focus background. (Are you still with me ? :-)) So this is probably the best setting for closeups of food. Many digital cameras have a "cuisine" setting which also adds extra red to give warmth to the picture. Do try it out if you have that option, because it will be designed for a tabletop setting. You may or may not like it but don't ignore it before giving it several tryouts on different foods. So back to the test. You have your SCENE set to PORTRAIT. Add MACRO (the tulip icon) as well to your portrait setting. Point to the subject and add some optical zoom until the subject fills the viewfinder and you are happy with the composition. Press the shutter halfway and check that your focus light doesn't blink. If it blinks, then unzoom a little or move the camera a bit further away from the subject. Press the shutter halfway again.....does the focus light still blink? If so, move back a little again. Press the shutter halfway again and once the focus light stays steady, press the shutter the rest of the way. Now take another 10 pictures in the same manner. Go and check them on your computer. Not happy? Do it all over again :-). The key to good photos is practice, practice, and practice again. You will find that you do get better as you learn and it's a great feeling! The way to get blurred backgrounds in tabletop closeups with a P&S is to get close to your subject and have your background items at least 20 inches away as explained above. The closer you are to the subject and using MACRO, the more out of focus your background will appear. To get a nice background blur outdoors is to have a subject ...such as this dish of fruit below (photo left)....resting on a table about 10 feet in front of a tree and hanging basket. I sat in a chair next to the table where the dish was resting and using PORTRAIT, MACRO and optical zoom on the bowl, took this closeup showing a background that was nicely out of focus. You can have some good effects when you get close to and zoom in on a subject which is a good distance from a dappled shrubbery background where you see pinpoints of light (photo right). You need to experiment constantly. Bokeh You may hear this word used by photography buffs at one time or another. Bokeh is the Japanese term for "blur" and refers to the beautiful creamy out of focus backgrounds behind a sharply in focus foreground subject. I haven't found out why we use a Japanese word but it does sound a little more exotic than just saying "blur". And here again I have to say that the best bokeh comes from the SLR (single lens reflex) cameras, both film and digital, just because one can use lenses with very wide apertures, wider than are seen on a P & S. There are other difference between the two types of cameras but I won't go further here. Point and shoot cameras are designed to take faultless, sharp travel and holiday photos of beaches, landscapes and family events with the least possible intervention of the photographer. They're made to be easy to use although they do have some creative possibilities if one so desires, in both the manual and semi automatic settings. Here are a couple of pics I took with my Canon EOS 30D DSLR where you see examples of background shrubbery totally out of focus so the subject stands alone. And here are a couple taken with the P & S, outdoors with a brass vase on a table about 20 feet away from bright shrubbery . I sat at the table, about 2 feet from the vase, used PORTRAIT, MACRO, and optical zoom to bring the vase closer. I moved my position slightly to the right to get two different shrub backgrounds. Do try to see what you can get using a similar setup in daylight. Best results are when the background has a dappled sunlight with light and dark areas and it fills the screen behind your subject. Use your MACRO and optical zoom or get close to your subject, aiming so both the subject and background are within the viewfinder (or LCD screen.) I think this is enough for one day. I did want to go into some visual diagrams to better explain how depth of field is altered by the aperture or opening of the lens. A wide lens opening gives a shallow depth of field and a small lens opening gives a deeper depth of field (all is in focus from near to far). Well there's always next week isn't there. Coming up will again be more about aperture shutter speed, and the meaning of f/ stops, but I'll go softly and keep explanations simple. It may also be handy to have a quick guide on how to open and set up your tripod. It's sometimes a very frustrating experience the first times you do it. I hope you are understanding it all and if you have questions please ask here or PM me. So thanks for joining me. I'll be uploading the next installment soon. And please feel free to save the pages on your computer. Sharon (Canarybird) :-) (All text and photos copyrighted) Free for personal, non-commercial use Follow-Up Postings: o RE: Food Photo Tips: Part 8 - Depth of Field clip this post email this post what is this? see most clipped and recent clippings * Posted by publickman (My Page) on Mon, Nov 2, 09 at 2:34 I did a lot more with depth of field when I used a film camera than I did with digital, and I'm still learning how to use my new digital camera. It was much easier for me with film. Lars o RE: Food Photo Tips: Part 8 - Depth of Field clip this post email this post what is this? see most clipped and recent clippings * Posted by canarybird (My Page) on Mon, Nov 2, 09 at 4:58 Lars depth of field is a cinch to handle with a DSLR, and lenses where you can adjust the aperture ...(f/1.4 to f/22). It's not so easy using a non-reflex digital camera. o RE: Food Photo Tips: Part 8 - Depth of Field clip this post email this post what is this? see most clipped and recent clippings * Posted by publickman (My Page) on Wed, Nov 4, 09 at 2:40 Unfortunately, I don't have that range of aperture on my camera - the maximum aperture is 2.8, which is not bad, but not as good as 1.4. The ISO range will go to 1000, which I find helpful, since I photograph in ambient lighting, aka fluorescent, in my office most often. I have been lazy and set the camera to be completely automatic for most of the photos I take of my cardboard furniture models, since I have to fix them in Photoshop anyway. I often cut out the background altogether. I also Photoshop out the reflections made from the tape I use to make the models. Lars o RE: Food Photo Tips: Part 8 - Depth of Field clip this post email this post what is this? see most clipped and recent clippings * Posted by canarybird (My Page) on Fri, Nov 6, 09 at 11:27 Lars is you can get what you want with fully automatic settings then that's great and it's true you can usually make adjustments in Photoshop or other programs. I had some disappointing results the other day with my DSLR in the Botanical garden where there are extremes of dark shade and bright sunlight. I'm going back there again and will use only automatic to see what settings the same camera chooses and how the pics turn out. Then I can go back again and hopefully fine tune my settings for some better pictures. It's all trial and error sometimes in difficult lighting situations. Luckily the entrance fee is just a couple of Euros. :-) SharonCb

Posted by canarybird (My Page) on Sun, Sep 20, 09 at 11:23 Food Photo Tips: Part 10 - Hi again everyone. I'm back with another entry on how to use your digital camera for taking tabletop photos. I apologize again for the delay in posting this next-to-last tutorial. After publishing the last entry I had computer problems and couldn't work until our repair man came with a new graphics card, which is now installed. The Self-Timer Function Perhaps you are accustomed to using the self timer so this will be nothing new for you, but if you have hesitated to try this very useful function on your P & S (point and shoot) camera you will be pleased to see how easy it is to not only to put yourself into a picture but also to sharpen some of your tabletop photos by avoiding camera shake when you press the shutter. Here is the icon for the self-timer and where it may appear on the back of your camera body: And here are the settings on my camera, which may be different on yours: And as seen displayed in the camera menu after entering the self-timer option you could have: OFF, 12 Seconds, 2 Seconds. The procedure to use the self timer couldn't be simpler. Assuming the camera is either firmly attached to a tripod or resting on a stable surface, find the self-time menu and decide how long you want the camera to wait before it takes the picture. If you are going to jump into a group photo, then give yourself the longest time in order to settle yourself comfortably in the photo, eg 12 seconds. On the other hand, if you are going to use the timer to avoid possible camera shake during a tabletop photo shoot while you stand behind the camera, then set the shortest time lag. Then press the OK button. Press the camera shutter button half way down and look to see that the green focus light doesn't blink. (If it blinks then you have to move the camera further or closer to your subject since blinking means the camera can't focus at the distance you have chosen.) When the green light is steady, press the shutter button all the rest of the way down. Take your finger off the camera and either run to join your group or wait without touching while it beeps a countdown and takes the photo. You've just used the self timer! By doing this you have avoided any possible movement of the camera that could occur as your finger presses the shutter button. While the camera is in countdown, you can do other things, such as holding a white reflector near your subject to improve the lighting. That's another advantage to using a tripod. Your hands are free while the camera takes the photo. The Flash Menu The flash menu is usually accessed by pressing the lightening bolt flash icon on the back of the camera touchpad. See again the above photo of the back of the camera with red arrows. Pressing the touchpad at that point brings you into the flash menu, where the icons are quite easy to understand. You may need to press the flash pop-up button (3rd photo) to begin using the flash. The flash will fire automatically when there is insufficient light. The camera decides if you need flash or not. Red-eye reduce mode. The camera emits pre-flashes before firing the regular flash in order to avoid red-eye. Fill-in flash. The flash will always fire regardless of light conditions. Useful for eliminating deep shadow on the subject's face when subject has back to sunlight, or in similar circumstances where you want to eliminate shadow. Always emits pre-flashes for red-eye reduction. Flash off. When the lightening bolt is surrounded by a circle or square, it means the flash will not fire even in low light conditions. Remember that a P & S camera flash will make your food look very flat and unappetizing, so don't ever use it for food photos. Photographing Silverware Although it doesn't quite fit in to the subject of food photography, a tablesetting is often included in a closeup food photo. Flatware can be a difficult subject to photograph due to the reflective surfaces, especially when dealing with spoons, where the room surroundings are often reflected in the bowl. I'm going to show examples taken in daylight by a window using white and black backgrounds, with and without a tripod. Here is my setup, using one and later two styrofoam reflectors on the dark side. Here below are examples on black velveteen. (One of my old Christmas party tops pulled from the back of the cupboard!) The first photo shows a bad example of how a handheld camera shot at this arrangement of three spoons reflects my hands and camera. In the next two photos, the spoons have been arranged differently so they reflect more the surrounding room. The following photos will enlarge with a mouseclick. Here at the left is another example of a bad reflection. Although the pattern of the silverware shows up nicely, the bowl again reflects the photographer. The centre photo shows a closeup using macro mode where the pattern is the prime object. But the picture on the right is not a photo at all, but rather one taken in a flatbed scanner. Don't forget that for posting to auction sites a scanned image may serve your purpose. Using the Tripod and Self-Timer When you have your camera set up on a tripod you will surely be able to take clear, sharp images of something as fine as silverware, where you want to display the pattern clearly. In order to get yourself and your hands out of the picture, using the tripod and the self timer allows you to duck out of the way so you are not reflected in the silverware. Here below is the sequence for doing this: 1) Photo left - set up the flatware on black velveteen, black or white paper or cloth and with camera on the tripod, adjust the level of the view and zoom a little until you are happy with the image in the viewfinder or LCD screen. 2) Photo centre - set your timer for the delay in seconds, enough for you to move away from the camera. Press the OKAY button to confirm your choice. 3) Photo right - press the shutter halfway and when the green focus light gives a small beep and a steady green light... press the shutter the rest of the way down. You haven't yet taken the picture but the camera is now counting down the number of seconds you have set, so move yourself out of the way. The shutter will open and the camera will take the photo without your touching it. Remember that if in step 3 the green focus light blinks rather than stays steady, the camera can't focus at the distance you have set. Change your zoom level (more zoom or less zoom) or if necessary, move the tripod further away. Here's the photo just taken in the example above, at left. Centre and right photos are a couple more done using tripod and timer where the reflection in the spoons is of the window. I hope you are understanding it all and if you have questions please ask here or PM me. So thanks for joining me. The next tutorial will be the last one, so I hope to have it ready soon. . And please feel free to save the pages on your computer. Sharon (Canarybird) :-) (All text and photos copyrighted) Free for personal, non-commercial use Follow-Up Postings: o RE: Food Photo Tips: Part 10 Self-timer, Flash & Silverware clip this post email this post what is this? see most clipped and recent clippings * Posted by publickman (My Page) on Mon, Nov 2, 09 at 2:45 I have a problem with the camera I am using now in that I often accidentally set the flash because of where the toggle wheel is place. My camera looks very similar to yours, and I find it very easy to press the flash without realizing it. Sometimes it is difficult to turn off the automatic flash, and this is most irritating. Most of the photographing I do now is of furniture and of cardboard models of furniture that I make at work, and I really do not need a flash for this. In the past, I have photographed wall sconces for tear sheets and these were difficult because the finishes were often polished silver plate or polished nickel. I had to be very careful about what was reflected in the mirror finishes. Of course I had to be even more careful when I photographed mirrors, and I often did those on a dock with the background very far away, so that it would be blurred. That was before I could fix them in Photoshop. Lars o RE: Food Photo Tips: Part 10 Self-timer, Flash & Silverware clip this post email this post what is this? see most clipped and recent clippings * Posted by canarybird (My Page) on Mon, Nov 2, 09 at 9:23 It's annoying when a flash goes off unexpectedly and also when the option to turn it off is buried somewhere down in a menu. Good idea of yours to take things outside to an open place if you can to avoid reflections of a room, but as you say, in the end one can also blur them out with an editing program.