We sci fi/fantasy readers NEVER give back books, but collect them and love them, returning to them when nothing new has come our way. I rarely get anything new here in Israel, so I rely on the one, maybe two used shops in Haifa, where the pickin's are slim and new stuff is a luxury and very expensive. My partner wails and moans over the state of my two bookshelves (messy, crammed, etc.) but I know exactly what is where. Years ago, my beloved books, which I laboriously brought with me overseas, was stored at an acquaitance's home while I relocated. There was a family fight, and her brother in a pique threw every book into the garbage, and I only found two survivors to tell the tale. Woodchip first edition of Our Bodies Ourselves, other jewels of sci fi fantasy from the seventies, you name it, GONE. Since then I've never let anybody have power over my library. I would curl up and fade away without my books, like without my garden. WHat I can't explain is my refusal to throw out a huge amount of old magazines, like The Whole Earth Review (I have them from when it was the Coevolution Quarterly); Mothering; the Sun, etc. Why do they mean so much? NO answer. Oh well, if this were only my wierdest quirk........

I did a big bookcase project using those metal standards you bolt to the wall. you can go to the Sagulator to see about width between brackets based on what you expect to put on the shelves. But what if you are stuck w/ a bigger span than the Sagulator tells you will work? Or if you want to use plywood or pine instead of some expensive hardwood? Remember that attaching a second board perpendicular to the front (like a lip, but on the bottom) of the shelf will strengthen it quite a bit--that's not reflected in the Sagulator's calculations. Here's how it works: you cut your 3/4-inch-thick plywood to the length you want, and to the depth you want minus 3/4 inches. Then you get a narrow piece of wood--maybe a 1x2--and cut it to the same length as the shelf. You lay the 1x2 against the front edge, so it points down. You apply a solid smear of wood glue between them, and you nail it in place. (clamp or strap it if you can to improve the glue bond). Maybe you can use a 1x1, which would probably be the same width as your shelf itself, but it wouldn't add as much strength as a 1x2. Sometimes this reinforcing wood is attached to the UNDERSIDE of the shelf right at the front; again, it's glued and perhaps screwed (since the screw head won't be visible), to keep it very snug against the shelf. Because this board is perpendicular to the shelf, it'll keep it from sagging (think about iti--ever tried to bend a 1x2 sideways along the wide face?) You can often reinforce w/ a strip of L-angle metal; it needs to be toward the front and it isn't as attractive as a strip of wood. Stronger, maybe but not as pretty. You can use something a bit smaller than you might need if you use wood, which would mean it impinges on your storage space less.. If you're worried about your ability to clamp or strap the wood to get a good blue bond, you could use the metal L-angles, and then on the front of the L-angle, attach a strip of lattice. One advantage of attaching that wood to the front of the shelf is that it will cover the raw cut edge of the plywood. But if you choose the L-angle idea, you can get the iron-on edge banding to finish the fronts. They make a snifty tool to trim the edges of the edgebanding. That's what I did, and the shelves look great. Plywood is the most economical way to get shelves the side you want. Trying to buy boards the exact width is more expensive than paying the lumber yard to cut the wood. I personally would avoid Home Depot bcs in my area, they won't promise to cut to exact size; I go to a lumber yard that will. Also, I've had people tell me this, and then tell me it wasn't true: When you have your plywood cut to size, be sure the surface grain of the top layer of plywood is running the LONG way on the shelf. NOT the short way; it'll bow more easily that way. Maybe it's not true on the 3/4 plywood, but I've seen this be a problem on 1/2-inch plywood, and I wouldn't take a chance on any other width. Another thought: remember that those brackets themselves take up space from the shelf below, so that front drop-down lip won't affect THAT much of your storage space. And, you might not want to have that many of those brackets across the span, just because they get in the way. So putting one on every stud might be a royal pain. I know for our bookshelves, we went w/ the outside dimension we could possibly get. OH, and to make it so the shelves would touch the wall between the standards, I cut out a notch where the standards would go. Next time, I'll get a hole saw for my drill and cut out a semi-circle at that spot; it'll be much easier. The 90-degree turns were a PITA. Feel free to ask me any more questions, either here on this thread or by e-mail. Here is a link that might be useful: Sagulator

Depending on what types of books you read, and keep, not all the shelves need be the same depth. 9" is deep enough for mass market hardbacks, for example. 12" is plenty deep for large books excluding oversized art books and coffee table books. The 12" deep shelves of my parents library have two books deep on many of the shelves at this point, although with that there is some slight overhang.

More great ideas - thank you! Newhomebuilder, I'd love to see your updated shelves if you wouldn't mind posting pictures. I see what everyone is saying about using primarily books and adding little accents here and there and unmatted, smaller photos. I also like other suggestions to use some larger objects so it's not too cluttered or random. I've edited the shelves down a bit. All but one item in the police collection went in DH's office and my Bell glass jars found a nice place on my dining hutch where they seem to complement my green milk glass. I'm definitely not one to just buy home decor items just to fill up space so I won't rush out to buy anything all at once. Most of the ones I do have I found while antique shopping or they were handed down to me and new things aren't as appealing to me as old. For now, I'll leave most of the pictures up and replace them with more books as time goes on. I like the idea of using the matted framed pictures as a display on the wall (love ttodd's picture wall) or on pictures shelves down the hallway. Lord knows I go up and down that hallway several times a day since the laundry and kids' rooms are at the other end! I'll have plenty of opportunities to enjoy seeing them :-D