The paint color on the lower half of the wall is just a very light lavender. The upper half is more purple. I actually mixed the lavender myself, by adding a little of the purple paint to some white paint. The fake tile (sheet vinyl) floor came from Linoleum City in Los Angeles. I looked and looked and looked for that vinyl and Linoleum City is the only place that sells it. I called a salesman there and asked about it. He said they had a unique contract with Tarkett (I think) to produce this product and he didn't think it was sold anywhere else in the country. Their number one client is Hollywood. Set-building people buy it by the roll to use on the sets. The sheet vinyl creates the look of early 20 Century hex tile floor in a jiffy. :) The light fixtures and medicine chest are reproductions. The light fixtures came from Rejunvenation Hardware and the medicine chest came from Van Dykes Restoration hardware. All these years of writing about old houses and I finally got to use some of the resources I've been writing about. Thanks for all the nice comments. Rose Here is a link that might be useful: linoleum city link

Here's the other issue with using 'wood look' stuff in a room that normally gets tone or tile...you can't use 'wood look' anything anywhere NEAR this floor. Sigh....yah. It's a design faux pas. Too many people want to 'try out' the wood-look tiles and they start with a bathroom or a kitchen. They do it. They live with it for a few months to a year....and then they want WOOD (real wood) elsewhere. Then....they realize they have to A) give up on wood or B) redo the kitchen/bathroom they just spent MONEY on. Have a think. Take your time. Think about your next 7 years worth of renovation projects. Do they include FLOORING? Anywhere? Any of those thoughts going towards wood, laminate or vinyl (all with a wood look???)? If I'm correct, please do NOT put 'wood' look in a stone/tile setting. You close the door on 'wood' in many many more areas. Use the 'wood look' stuff for areas that are TRADITIONALLY wood floors. As soon as you use the 'look' in a 'wet area' you need to be prepared for the consequences.

@Amir Ali - I just wanted to post a comment in order to: 1. Let you know that I completely understand what you are going through right now. I have TWO FAILING slate floors that are part of current bathroom renovations. The master bathroom floor had not been grouted due to delays on his part. I discovered that some of the tiles were COMPLETELY LOOSE - and some sounded like they were only partially bonded to the floor. This floor is failing - and it has BARELY been walked on because the bathroom renovation basically stopped due to issues - bathroom isn’t usable so the only use has been when I’ve gone in there to take photos or measure something = maybe some tiles had been walked on four or five times before I started discovering the loose tiles. It is obvious that the tiles failed to bond to the floor - the mortar must have skinned over or something. I am NOT reinstalling the loose tiles. IMPORTANT - my former contractor does not fit the definition of what people here on Houzz love to refer to as a “hack” (at least not the actual business that I hired to do the work) - however, his employee clearly did not know what he was doing (or just didn’t care) - and that makes the owner of the business liable for this work. The business has hundreds of Google ratings (4.9/5), owner is a member of TCNA, I had several reviews from people I know (and trust), and I DID NOT JUST TAKE THE LOWEST BID - I am NOT a CHEAPSKATE. I am so tired of people AUTOMATICALLY blaming the homeowner when they have ZERO basis to do so. Making assumptions and basically telling homeowners that they are IDIOTS and CHEAP really makes me upset. Okay, I’m finished with my rant! 😂 The ”fix” is this: The ENTIRE floor is being torn apart. Not only is the tile being removed, the cbu will be taken out. New contractor assumes that he will also find that former contractor failed to add the required second layer of plywood in order to make sure that the substrate was prepared correctly in order to have a natural stone floor installed. Based upon the above issues, I investigated the slate floor that was installed in one of the other bathrooms back in April. I noticed a few grout issues - and as I went around knocking on each tile, the sound on many tiles indicates tiles that are only partially bonded. This is what the floor looks like from a standing position: And this is what it looks like when I realized that I needed to inspect it after the failure in other bathroom: I have cracks and broken spots of grout in many places. I also have some grout which is stuck on my tile because the contractor failed to seal the tile (as required) prior to grouting (I found this out later - I was in the hospital while this floor was being installed) and made promises over and over to come remedy the issue. So, this floor will also be ”fixed” in the same manner as the first one - I’m just waiting to have it ripped out until after the other bathroom is completely finished. 2. I also wanted to let you know that regardless of whether (i) you have a written contract, and (ii) that contracts specifically provides (or fails to provide) a five year (or however long) warranty period, you still have recourse against the contractor who installed your tile. Most states (probably all but I haven’t done research on this issue in every state) have enacted statutes that protect homeowners for this type of issue. In my jurisdiction, there are specific statutes that relate to home renovation projects - these statues require (among other things) that all work must be done in a good and workmanlike manner. Following industry standards, as well as manufacturer’s specifications, are part of this requirement. Also, the consumer protection act in my state also protects homeowners against contractors who perform shoddy work. I am 99% positive that your state will have some similar statutes. If you want to share your jurisdiction, I am happy to take a quick look in order to point you in the right direction. MANY jurisdictions require the homeowner to provide the contractor with notice and a right of remediation. Unless you follow the requirements of your particular statutes, you won’t be able to bring an action against your contractor to recover damages. FYI - my former contractor has chosen to ignore the notice I provided, so I then was free to hire another contractor to do the remediation work. My former contractor will owe me the money I have to spend to correct his failure to properly install my tile (which will greatly exceed what I paid him - removing tile + cbu + buying new material (including nice slate tile - because I didn’t purchase cheap slate tile for the the project initially). I am sorry that you’re going through this because it is NOT fun. I decided to consider myself “lucky” because he hadn’t yet installed this tile on my laundry floor! Hopefully, you won’t have water damage that will require even more remedial work in order to fix it.

Since you seem to love this tile, what about trying to use a white caulk in the corners instead of the contrasting color. It may make the tiles look like they fold into the corner. You can try this before by just cutting some strips of paper and taping them up , then step back and see what you think. On a side note - was the floor tested for water? Those tiles are too big for a regular shower drain - it probably should have been a trench drain, unless there are diagonal cuts through the tile pitching them all to the drain ( can't tell in the picture ). Be careful moving forward - there seems to be some incorrect things happening here. Good luck!