I am going to make a guess that you are using Microsoft Word...since you didn't say. Also, I'm assuming you're looking for a free template as opposed to a paid one. Why not just create the template that you want? Experiment a little with the fonts & page layout, inserting graphics where you want them. When you achieve a satisfactory result, SAVE IT AS A TEMPLATE, not a document. That means FILE : SAVE AS and then save it as a .dot file, not a .doc file. There are other options, but if you require something that cannot be done in Word you might need a desktop publishing app such as Microsoft Publisher ($) or the free one in the link below. If these do not satisfy, there are other options if you are willing to work in the OPEN DOCUMENT FORMAT, which would require you to install either Open Office or Libre Office. Here is a link that might be useful: Serif Page Plus

Our fabricator said if he had flipped the granite 180 degrees the veins didn't match and it was too gold. I think the golder area would have looked better than the blue. His real mistake is to not have asked us. If we had been asked we couldn't have complained about it. We didn't want to buy a 3rd slab but if the fabricator had told us we'd have a poor matching seam we would have considered it. I'm just not sure how to handle this. I'm going to ask to see the rest of our slab. The fabricator says there's not enough to redo the countertop but I want to see for myself. If there's not enough we'd have to buy a slab from another bundle and then there'd could be a worse mismatch between the island and the counterop. What would you tell the fabricator to do? Thanks again - our contractor claimed we were the first people to complain about the seam in natural stone. It was SO helpful to let him know we had posted pictures and plenty of people agreed with us!

it makes me feel a better to learn that i was not the only one that went through this! i ended up writing a brief agreement with the cabinet maker as he did not have one either. contents pasted below, was a 2 pg word document: AGREEMENT Re: Project #_______: Design services, custom kitchen cabinetry and installation SCOPE OF WORK � Design and provide design documentation of kitchen cabinetry and kitchen layout based on mutually agreed upon design between homeowner and ________. Documentation will be provided electronically via PDF file format. Documentation to include: graphic of cabinet design with measurements and kitchen layout graphic and measurements to facilitate installation by ________and to enable communication with General Contractor _______. � Fabricate and install kitchen cabinets as per design documents � Deliver cabinets to homeowner�s site for installation � Provide and install blind corner pullout mechanism, model # Rev-A-Shelf 4WLS882-35-570 � Provide and install 50 quart double trash bin/recycle pullout, model # Rev-A-Shelf 5349-2150DM2 � Provide and install custom integrated panel for client-provided Miele dishwasher � Provide and install crown molding as specified in design diagrams � Summary of kitchen cabinets: o Face frame with full inset doors and drawers � unfinished with modified curved "Rockridge" leg detail (as defined in design document) o Cabinet boxes are constructed of 3/4" (9-ply) pre-finished maple plywood where cabinetry is hidden by a solid door and �" (9-ply) unfinished plywood where cabinet interiors will be visible through glass door panels. Face frames are constructed of poplar. Cabinets will have Blumotion concealed hinges and include Blumotion soft close dampers installed at the top of each cabinet. Three shelves will be included with each cabinet and all shelves are adjustable using a movable pin system o Doors and drawer faces are constructed of solid hardwood Maple o Drawer boxes are constructed of solid dovetailed maple with a clear finish applied and installed with Blumotion soft close invisible full extension slides. All drawer bottoms are constructed with 1/4" plywood and have a weight static rating of 75 lbs with the exception of the 3 oversized drawers which will have 1/2" plywood bottoms and a static weight rating of 110 lbs. o Cabinet interiors on sink, trash pullout, blind corner lower, fridge, and all non glass door uppers will be of finish grade maple (pre-finished before delivery). o Cabinets with glass front doors will have interior of paint grade plywood ready for priming and finish coat of paint o Quantities: (change order to be issued should final design require modified total) � 29 solid hardwood maple doors/drawer faces � 10 Upper plywood cabinets (blind corner upper counts as two "cabinets") � 9 Lower plywood cabinets w/ 1 blind-corner pullout. (Blind corner lower counts as two "cabinets" & fridge panels count as one "cabinet"), OUT OF SCOPE � Glass for doors (their installation IS included) � Drawer pulls, latches and knobs (their installation IS included) � Under-cabinet lighting � Priming and painting of paint-grade cabinetry and moldings � Countertops/Sink/Appliances/Electrical/Plumbing PROJECT SCHEDULE Full set of draft design documents referenced above to be provided by January 16, 2011 and all design activities and documents to be completed and mutually agreed upon with homeowner on or before February 6, 2011. Fabrication and installation schedule to be developed based on mutually agreeable schedule between homeowner and __________, with cabinetry to be delivered to job site on or before April 30, 2011. PAYMENT SCHEDULE Milestone Payment Due Comments To commence work Upon fabrication completion and delivery to job site Upon installation and completion of job Total including tax and delivery Date: Signature:

I'm not sure what you are wanting...an outline of Mickey that you can draw around? The scrapbook store I go to has tons of Mickey stuff...you can check out the website at: Expressions with Heart. You can e-mail her and ask for what you need..she will or and mail stuff to you also...