aam31, the Amalfi which is what I sat in at Ferguson is around that width, and my husband and I felt comfortable. For reference, I am a 6'1" female and my husband is 6'0" and we are both broad shouldered. The Mozzano is 29 inches wide and I felt it was a little snug and I also didn't feel like I could stretch out as much. Not Bob the Builder, I can see why you would say that. I am a very tall female with long legs. My husband and I are runners and it's important for us to have a nice tub that I can stretch out and soak in after long runs. My old house had an acylic garden tub and although it was nice and deep, I couldn't even straighten my legs and it didn't hold in heat. I am choosing a V and A tub because it has a 25 year warranty and it being made of stone, it will hold warmth in longer so I can soak comfortably longer. I feel like it's worth the investment :)

"I could also just get a pull-down faucet for the sink and aim it at the tub to fill it." You could - but you won't like it. The most one of those will fill is 2.2 gallons a minute - some less that that. Divide your tub's capacity by that and you're looking at 20 minutes to fill +/- Not good. beekeeper - I have one of these and have placed more than half a dozen in projects over the past few years. What you get for your money is a machined brass body that mounts in the ceiling or wall and a plated trim piece. The body is a substantial piece of hardware and chrome,brass, nickel plating costs $$$ too. Whether that's all worth 500 + bucks, is up to you. Like davidro says, it doesn't matter what the delivery system is, this is just an opening for hot water to come out of, albeit one with a bit of engineering. GD & Spanish - the splashing is very much dependent on the mounting height of the unit AND the tub selected AND the location of the water column inside the tub. Mine hardly splashes at all. The ones I have seen that splash only do so for a minute or so until their is enough of a pool in the tub to counteract it. Flat bottom tubs with tall ceilings are going to splash more than one from 7' into a sloped contact point in the tub. Besides , we're talking water in a bathroom, generally tiled so what's the big deal ??? It's not like the amount of splash is the same as taking a shower and leaving the door open. 2. While you are correct in that "the water cools off much more than it would from just a regular tub filler", it's not as if it cools off enough for anyone without a thermometer to tell a difference, and a very sensitive one at that! Sure the air cools the water more from a stream falling from 8 feet than one falling from two feet. But bath water that is 100 + degrees is not going to cool down to 90 deg. in the xtra 1-2 seconds it takes it to fall from the ceiling- get real. Additionally , that filler produces a very dense column of water (laminar) that has little to no air in it, so one might argue it will be hotter and less prone to heat loss than a "regular" filler that introduces room temp air into it's stream - thus cooling it off on it's way to the tub. So don't worry Spanish -your tub will still be plenty hot with that filler if you choose it. IT'S A NON -ISSUE people. I've already alluded to the real issue for lower tub temps - FILL TIME. That's directly related to the delivery system ( valve). If your valve and accompanying filler will only deliver 5 gallons a minute it's going to take a while to fill an 80 gallon tub, and there will be some heat loss. Select a valve that delivers 20 gallons a minute and you can be soaking quicker that most people can undress. Here is a link that might be useful: laminar valve body - see page 2

I know this is an old thread, but reading through it - as someone who has bad knees and pins and a plate in one ankle, how on earth is a free-standing tub easier to get in or out of? There's NO way to reach a functional grab bar, for heaven's sake!!!!

Stacey- No...as I mentioned in my first post, I got a wall-mounted one for about $400. You can see it in the picture I posted. I like a simple and clean look and the floor mounted ones look like fancy, exposed plumbing to me. If you can run your supply pipes up into the wall, all you need is the valve that's hidden in the wall, like a shower valve, and the spout and and handles that are surface mounted. l also like it because it doesn't take up space, and you don't have to worry about the structural issues that a floor mount sometimes requires,especially if you have to go through tile. My wall mount does go through wall tile, but I prefer that as it seemed easier than plumbing that has to go through and be secured to floor tile. Just my preference, but it made tub filling a whole lot cheaper. P.S.: I could have gotten a cheaper tub, but I preferred getting a name brand I had had good experiences with before. I'm sure that there are good quality tubs out there that sell for less than what I spent, but I'm not an expert on tub brands. I was simply happy spending $1620, as opposed to $3000-6000 locally.