I need help with installing hexagon tile around my window
Kimmy W
7 months ago
Featured Answer
Sort by:Oldest
Comments (11)
millworkman
7 months agoRelated Discussions
Help! My builder says we can't tile around whirlpool tub.
Comments (12)There are myriad solutions to this. The access panels can be put in an adjacent closet or can come through an adjacent wall. Or if on the first floor, they can be on the bathroom floor with access from the basement below. You can do a wood wainscot with removable panels. You can do a fully tiled apron, with a removable tile panel. Often times the "grout line" between the tiled access panel and the permanent field tile will be filled with color-matched caulk instead of grout. If access is needed, score the caulk with a utility knife and pop the panel off. The panels can be held in place with magnets, velcro, or some other mechanical means. I'm not a big fan of the caulked option, I'd rather do a removable tiled panel that has a lip to it, the lip can be tiled, a rope design, a piece of tile as the trim, etc. But that's my personal preference. As a builder and a tiler, I look at easy access for future or periodic maintenance. It's not that the caulked panel is difficult, I just prefer totally accessibly and non-destructive options. A tool-less panel that can be popped in or out at will. If you want your front apron to be just plain field tile though, then the caulked panel is your best bet. You can tile the apron, but have a wood "cubby" built in to the apron. Think a small niche. The cubby can be used to hold rolled up towels, or small notions, what ever. The niche can be popped out to access the tub's mechanicals. We've had a few threads about this, but I did a search and came up empty. Don't let your builder's lack of skill or imagination restrict your design....See Moreneed to install windows installer help
Comments (23)one thing to remember since that pc had xp sp2 on it prior to going to the shop and he put sp3 on it if a system restore was done to a date prior to install of sp3 it can cause major issues, you will end up with a mish mash of both. Back when everyone was doing sp3 installs it was highly recommended not to do a system restore because of that, instead the recommended method was to go to add remove programs and remove it from there. However since you already have sp3 on the pc and the tech did this and you had asked him not to and now you have problems the best and logical thing to do is bring it right back to him and tell him it needs to be fixed, He apparently did not check to make sure everything was working properly. You paid for it to be working he should make it good. If you can have it with sp3 you definitely should have it with sp3 so you can continue to get your windows updates on it. Thats my thought anyway....See MoreWindow Installers ruined my original woodwork! Help!!
Comments (7)I think that these idiots are just plain not capable of fixing anything to your satisfation. Though they should fix it, and they should be responsible for it, I have my doubts. No matter how much you squeeze, you can't get blood from a stone, and you can't get good work out of people who don't know how to do it. You might be able to get money out of them, and if so, the easiest way to fix it is to have a good lumberyard or finish carpentry contractor/shop rout you new molding to perfectly match the profile of the old. The wood would be new (unless you had old wood to give them, or they could locate some, which is possible), but you could experiment (on scraps of the same wood) with stains and finishes to get it to look close to the original. If you're fixing it yourself, then you should look carefully to see if you can find pieces in lumberyards to put together to match your old woodwork. I've lived in places from the late 19'th C. to the mid-20th C., and in each place, the moldings were either built from pieces that are still around, or simpler 1-piece moldings are literally still for sale in the more upscale local lumberyards. A good lumberyard should be able to get you the pieces in pine, maple, red oak, or occasionally cherry. This is something that most homeowners don't know about, but can save you tons of money when restoring your old woodwork. To fix your old wood without replacing it, you can fill the problem areas with putty and dab stain & finish (probably shellac?) on top with a paint brush and sand it flush with very fine-grained (220 or higher number) sandpaper (draw in the grain lines with a pencil). I've also seen colored hard wax burn-in sticks that you melt with a soldering iron, mix to the right shade, then fill holes and dents with. I think you can buy it from Van Dykes Restorer's catalog. I saw a guy do it once and I couldn't see the repairs, honest. Or you could cut some patches out of wood (especially if you have some old wood around that might match well), cut out really bad sections of your damaged molding, and glue the new wood in place. The patch would show, but you can sand it down flush with the old molding, and it could look OK anyway. Good luck!...See MoreNeed help 3x6 subway tile backsplash around refrigerator?
Comments (4)No bull nose. My designer suggests running it the length of the counter and then running small pieces on the right side of the window to make a straight line up (on the left side of refrigerator) and then straight line from counter to edge of cabinet on right side of refrigerator. Nothing behind refrigerator. I have no experience with back splash install and want to make sure it's done correctly since my neighbor is installing and doesn't do it for a living. ;)...See MoreRedRyder
7 months agoHU-227031627
7 months agoDeWayne
7 months agoKimmy W
7 months agoKimmy W
7 months agoDeWayne
7 months agoKimmy W
7 months agoKristin Petro Interiors, Inc.
7 months agoKimmy W
7 months ago
Related Stories
REMODELING GUIDESContractor Tips: How to Install Tile
Before you pick up a single tile, pull from these tips for expert results
Full StoryGREAT HOME PROJECTSHow to Install a New Tile Floor
Is it time to replace your tile floor? Here’s how to get it done, which pros to call and what it will cost
Full StoryKITCHEN BACKSPLASHESHow to Install a Tile Backsplash
If you've got a steady hand, a few easy-to-find supplies and patience, you can install a tile backsplash in a kitchen or bathroom
Full StoryTILE6 Questions to Answer Before You Install Tile Flooring
Considering these things before tackling your floors can get you a better result
Full StoryGREAT HOME PROJECTSHow to Install Energy-Efficient Windows
Learn what Energy Star ratings mean, what special license your contractor should have, whether permits are required and more
Full StoryWINDOWSContractor Tips: How to Choose and Install Windows
5 factors to consider when picking and placing windows throughout your home
Full StoryWINDOWSDiamond Muntins Help Windows Look Sharp
As the real deal or a decorative grille, diamond window muntins show attention to detail and add traditional flair
Full StoryREMODELING GUIDESFinishing Touches: Pro Tricks for Installing Fixtures in Your Tile
Cracked tile, broken drill bits and sloppy-looking fixture installations? Not when you follow these pro tips
Full StoryFLOORSHow to Get a Tile Floor Installed
Inventive options and durability make tile a good choice for floors. Here’s what to expect
Full StoryBATHROOM DESIGNHow to Match Tile Heights for a Perfect Installation
Irregular tile heights can mar the look of your bathroom. Here's how to counter the differences
Full Story
Lomo