Here are some pics of the Lato Base that has been installed for about 1 month we ordered it in the summer and it arrived in December due to the pandemic supply chain boat traffic jam. it seems nice. it is lower shine and much more non slip than our previous laminate and warmer on cold mornings. +/- you cant run and sock slide on it. we replaced laminate that was light but more colorful in orange and pink hues (bottom pic is our old floor-notice how you can see the edge of each lamite plank. For a plastic floor, this Lato is more “realistic” than the old floor which had multiple boards per plank. Lato is light and looks best in the rooms with deeper contrasting colors imho. Maybe we will go darker on the walls the next time we paint Our house is 100+ years old. The Lato feels like a timeless color and I against our dark modernish Ikea cabinets. we did 900 sqft continuous over multiple rooms on the main floor we’ll see how it holds up long term. my kid roller skates on it and plays hockey on it with no marks or scratches that havent cleaned up. we clean it with liquid products and have the pet water dish on it without worries. The micro bevel is about as deep as the faux wood grains. We were not a fan of the deep grooves and trendy big planks but maybe this flat bevel will present a problem if any buckling or swelling occurs in the future. We’ll see. Under can lights and other fixtures it looks nice and doesnt mirror the light source. There are certain times of day that the light shows the artificial grains more. Overall, it looks good, but i doubt folks would be fooled that it is real wood while standing on it. But, it seems to have gotten firmer with fewer soft / hollow spots as it has sat and settled . . . or im used to them now. Subfloor was 23/32 tonge and groove particle board over exising imperfections from settling. Its not perfect but better than it was before particle board was laid. the negative- The wear layer is brittle. we did find a crack in it from an unknown source. Not sure if something was dropped or maybe a kid was testing dads hammer while he was not around after install. also in one of thr doorways, there is a gap in the subfloor it was soft and a plank cracked in half when someone stepped on in that spot. the previous laminate had spanned that soft spot without cracking. we did not use an approved installer. lesson learned we are going to see if we can replace just one or two tiles by cutting the tongue and gluing in a replacement as seen on line. hopefully others will not see the negatives that we have experienced. this is our first luxury vinyl and maybe the problems would have surfaced with other products too.

Living with my Karndean Warm Ash 9" planks for 2 months. Its very pretty, love 9" and the color. I was going for exactly whT the OP was goung for and the look is right. But. Has no bevel. Not Into cleaning, the idea of any bevel sounded gross with my not so often cleaning. Wish I had done a micro bevel if it was avail. Didnt even consider and wish I had. Prof install, Karndean is not maybe the best but decent brand......the ends of the planks stick up just a tiny bit. Most noticeable when walking down the hallway as the planks are laid Ling. Really distracting. And of course I can't imagine it not chipping. Really sad, super expensive small new build. Other thoughts, I hate the grain in lvp. although I went with a very minimal grain, again the idea if dirt building up in the grin was gross. But even with minimal grain you notice if you Re sweeping with or against the grain. You have to sweep with the grain. I have soft spots that you can feel give. Drives me nuts. No noise, just give. Btw that and the flex in in the trex I feel like I'm living in a fun house mystery spot. Wish I had gone glue down but assumed it was some cheap way to go. It can be fixed, click cannot. No give.

https://www.prosourcewholesale.com/products/vinyl/resista-plus-h2o/drifter_11820030101677_40762588?fbclid=IwAR3Dey5pZpWyBZ9SoamAh6q4lpgcUlNwBBCdXXOuC9WrNE8618Rxm7TZoYI for the Resista Plus H2O EVP 9"x72" Drifter Vinyl Flooring 6 colors available Color: Drifter

Here is a followup to my original posting. Installation of the plank flooring is rather easy but preparing the subfloor is anything but! We are very happy with the final results but getting there wasn’t easy. Some of the SUPERCore Xtreme, Cattanooga Hickory, has been down for more than a year. None of it shows any signs of wear, even when inspected carefully. We vacuum all of the floors in the house every week using 2 inexpensive eufy robo vacs and mop once a month. The color does not show the dirt easily. If you walk on it when it is wet after mopping, it often shows footprints when dry, during certain times of the day when the natural light is just right. I expect the floor to be looking good long after I’m gone. I think the SUPERCore Xtreme, Cattanooga Hickory, is an excellent product. It is really tough. It locks together easily if you follow the directions. Delivery was only one week late; very good considering the supply chain issues at that time. The planks had 5 distinct patterns. I was expecting 6. Bear in mind that the characteristic feature of a pattern, such as a unique knot, can appear on the left side or the right side of a plank and might appear at any location along the length of the plank. So there is a lot of variation among the planks. Before putting them down, I separated a few boxes into 5 different piles of planks, based on the pattern. I installed the flooring in our smallest bedroom first, by myself in November 2021. Waited for spring to resume work. I hired a helper in May 2022 for the remainder after a knee became very painful. My helper connected the planks together and marked the pieces to be cut. I selected the planks from the piles for him to put down and and made the cuts, so I could remain on my feet. I used an electrically powered table saw, jigsaw and a mitre saw to make the cuts. Discovered weeks later that I tore the lateral meniscus in my right knee, probably from getting up and down from the floor so much. Had surgery on the knee in November 2022. Not sure when I’ll start the last small bedroom. All rigid core plank flooring that locks together and floats on top of the sub floor requires a subfloor that is unusually flat. The floor does not have to be level. It does have to be flat. If the subfloor has significant peaks and valleys, (high spots and low spots) the relatively rigid planks will bridge over the low spots, leaving an air space between the top of the subfloor and the bottom of the plank. Stepping on a plank that is bridging over a low spot will cause a popping or snapping sound. You may find the popping and snapping sounds to be annoying. I have learned that most of these noises subside, almost completely, after several months. If the valley is too deep, your weight will stress the tongue and groove locking mechanism too much. Repeated stepping on such a spot will likely cause it to fail. Then the planks may move independently of one another and come apart. That would be a serious problem. Our one story home was built in 2000. It has a concrete subfloor. I have installed the SUPERCore Xtreme, Cattanooga Hickory in one small bedroom, a large bedroom/sitting room and a laundry room. In every room I had to flatten the subfloor before installing the plank flooring. I did the small bedroom first. After watching several Youtube videos, I decided to grind down the high spots instead of filling in the low spots. I bought all new gear to do the job, since I had 950 sq ft of flooring to install. That was a big mistake. Grinding down a concrete floor is an extremely slow, noisy, dirty, dusty, hazardous, and physically demanding job. Here is a photo of the floor in the small bedroom. In subsequent rooms I filled in the low spots with LevelQuik RS Self-Leveling Underlayment, made by Custom Building Products. Mixing and applying this product requires at least 2 people. It’s sold by The Home Depot and others. I did not cover the entire floor with the leveling compound. That would have required about 3 times as much leveling compound and would have raised those floors about ⅛ “ which I didn’t want to do. (Self-Leveling is a misnomer. The stuff is the consistency of thin pancake batter and requires some assistance and tooling to make a smooth flat surface. For the purpose of creating a flat subfloor for plank flooring in a home, I suggest that you add about 10% more water than the directions indicate. Doing so will make it flow better without adversely affecting its performance when cured.) Prior to applying the leveling compound, I applied Multi-Surface Bonding Primer (MBP) to the concrete floor to ensure a tight bond between the original concrete and the leveling compound. (MBP is also made by Custom Building Products.) If you use the MBP you can feather the leveling compound to zero, and don’t have to maintain a minimum thickness of ⅛” over the entire floor. Here are some photos of the floor in the large bedroom completed in June 2022. Finding the borders of the high and low spots is tedious. Next time I will probably pour water in the previously identified low spots of the floor. Then I’ll mark the boundaries of the “puddles” with a large permanent black felt tip maker. Then vac up the water, let dry, apply MBP, and finally the leveling compound. The floor in the laundry room between the garage and the kitchen gets a lot of abuse. It was installed in September 2022. As you can see, the color of the flooring is highly dependent upon the light. That's why it's important to look at samples in your home. Paige; The Flooret Modin Base Soho sample that I tested was more abrasive compared to the SUPERCore Xtreme, Cattanooga Hickory sample. I hope this update is useful for some of you who are considering rigid core vinyl plank flooring.