Here's the risk to repotting too soon: that the roots haven't filled the pot, so the rootball won't still together, it will fall apart when you take it out of the pot and break off a bunch of the delicate feeder roots, setting back your plant. I've potted up after 3 weeks many times. I can gauge time to pot up by two simple things that have little to do with top growth: seeing feeder roots in the drain holes and being able to turn a well-watered pot upside down with my hand holding the plant in and having the whole rootball tap out cleanly. That's all I know. Whether 9 days is long enough in Florida to equal 3 weeks of root growth here is anyone's guess. This is the season of top growth, so don't be fooled by that. Haven't you found a source of free pots from landscapers?!?! Or is it too hot to use plastic nursery pots down there?

"... Her house build demonstrates that. She described the floor and stair riser issues in her first post ..." She does not go into detail on why the condition of the construction is the way it is. You are assuming it was all the gc's fault. While I am certainly not going to defend the GC she fired, I will say part of that condition might have been from the house being open to the elements for a period of time. ANother part was that she never gave the original GC the opportunity to make the work that was done ready to be installed over. The GC did not complete the project and was removed from the job before he could finish his work, so of course it was not ready to be installed over, because the work was not completed and the original GC did not have the opportunity to make sure the stair system or any other part was in a ready state to be installed over. She very well may have had just cause to remove the CG, but nevertheless she took on the GC responsibility on herself to ensure it was ready for finish trades. I believe it is apparent that this house was not ready to have finished trades in it performing finish work, and it was her responsibility as GC to make sure it was unless soneone else accepted that responsibility by contract. "...A person does not require a GC to have a floor put down. ..." The problem with this is that it was not as simple as getting a floor put down in a home that was ready to have finish trade present. Again, we do not know what caused the stair issues, which could have been: Framing problems caused by the GC's incompetance, or being open to the elements, which flooring installer holds no responsibility for because its a hidden condition, unless it was a tile contractor who must check for build stability, and deflection and rigidity requirements. You might not be aware that carpet, wood, and resilient installers are noit trained for, nor do they hold any responsibility or liability for framing issues. All of which she holds responsibility for as the project GC. The only way the flooring installers would hold liability and responsibility for framing (hidden conditions) issues is if it was addressed on their bids that they agreed to do the work. Any flooring installer would address this in their bids if they elected to take on the added responsibility and liability from stair framing condition and height requirements she may ahve had which could only ahve been taken care of with additional prep they should have addressed in their bids if they wanted to take on the additional responsibility and liability for an added fee. Additionally, she admitted she has no local building codes for such things as stair height. Could they have done better...sure. But it begins and ends with who is liable and responsible. She took that on by electing to be her own project GC. "... While it might have been possible for her to have stepped in earlier to babysit the install where she would have seen that they weren't able to handle the job, stopping it sooner than what happened, that doesn't relieve that company of their total responsibility for having installed a floor over an (obviously) unsound substrate. You can't remove prep from the flooring equation. The flooring company is the professional here and in charge of their own work. It's their job. Once they start putting the floor down, they have accepted the substrate as sound and taken ownership of the results. They did not act responsibly or professionally. Period. Doesn't matter who did the hiring. They and they alone are responsible for their own incompetent work ..." Again, (and again, and again, and again) an installer absolutely is responsible and liable for the surface they install over. However, I will disagree that prep cant be removed. It very well can, and often is removed. While most professional flooring installers do much surface prep, others do not, and FEW, if any, will concern themselves with framing issues AT ALL. I do, but most do not. It all boils down to what was included in the bid. Flooring installers have no responsibility to do added prep work unless they agree to be contracted to do it. They ahve every right to stop work, tell the GC this or that prep needs done before continuing, and tell them to give them a call when its ready to be installed. Lastly, you seem to be taking everything she says as gospel. I dont. I have alot of experience with customers, and customers lie alot... and often. Mostly to save face, save a buck, and/or to shirk their responsibility. The customer is not always right. Thats a falicy. I find it hard to believe that she had issues with the GC, then issues with all the trades. Everyone was wrong in every aspect of this project ... except her. I dont believe that for a moment, but I am not saying its impossible. What I see as possible is someone who bit off more than they could chew, and is blaming everyone else. I am not stating no one else holds any blame though. Could be a little of each. Bottom line its mostly her responsibility unless she has a piece of paper saying different ...except the subfloor issues which the installers absolutely are responsible for if they elect to do the prep and/or install over it.

Thanks skydawggy. Any way to tell what series it is from the label? The only model information I was able to find from the label was: Part #: P-PLFIX-13711287 Plfix fixed proline model 1 unit Contour standard colonial 4x4 The Pella website is no help. Is there some characteristic of the window that I can look at to make sure it's not a 200 series?

hi and thanks, romy. I think I understand your question, so I'll answer what I think - the fridge is the end of the U see image of outdated, but generally accurate floorplan so you can see - there's no room to just do both. it's definitely one or the other. Fridge is to the bottom right. fridge wall will come flush with wall leading to pantry.