This Milgard bay window is about 10 years old. I wish I knew then what I know now, pay the extra $$ for UV protection on the glass. The sun is the process of ruining the cushions, they're so faded. Not even the UV spray I bought from Calico Corners stops it. That's one reason why I put up the sheers, to slow down the deterioration of the cushion and pillows. For some reason it hasn't faded the barrel pillows as much as the cushion. When it comes time to replace the cushion fabric I may have to go with Sunbrella fabric to be sure I'll never have this problem again. Something to keep in mind when you're selecting fabric for your bay window. From personal experience I can tell you that eastern exposure in California is not kind to fabric in windows. I pulled the cushion away from the window, you can see the window goes from top to bottom, no place to hang curtains! I finally came up with a solution, buy cafe rods and hang them upside down from the only wood surface inside the bay...the "ceiling". With an all-vinyl window there's no other place for the screws to go. Hanging curtains on the wall doesn't block the sun from the fabric inside the bay, because the curtain would be on the outer edge of the bay. I was looking for a way to block the sun from getting inside the bay window not inside the living room. No one makes a small curtain rod to hang upside down. The other problem you can see from the pictures is how low the window goes, straight to the floor of the bay. So we can't use a very high cushion. This one is 2.5" high (or 2.25"). I have never had a problem reaching down to open the window, there's a lip that protrudes, that's what your hand pulls up on to lift the window up. DH built the frame for this window and he didn't take into consideration that you need to have a few inches of wood on the bottom, he should not have taken the window all the way to the horizonal base. Live and learn. What I do like about the cushions is the foam they chose, it's pretty firm. I made it very clear to the designer that I did not want to feel my butt hitting the wood base when I sat down on the cushion. For a cushion that narrow to support a body without mashing down, well it has to be firm. I'd prefer a softer look, not so tight like this one is...but then it would probably have to be thicker and then I have to deal with reaching down behind the cushion to find the window lip. I thought I would read and lay inside this window but I never have. I attribute that to the lack of a wood frame because leaning up against glass is very unsettling, expecting it will shatter. So it's mainly there for show. I think that covers all the issues I've had with this window. My advice is to think about comfort and sun-fade when you're deciding on fabric for a window. Even a few hours of sun can do a lot of damage. If your window has UV protection then consider yourself lucky...or smart that you made the wise decision to add that option to the glass. The money I saved by not doing that has ended up costing me more in fabric.

By cafe curtains, do you mean the tiered set? I'm just not sure what that means? I always think of kitchen curtains! How would I mount a curtain rod from the ceiling? I once had regular curtain rods before I put in the seat, but with the roller shades, there is no place to put the rod hooks. I don't want to block off the windows as in the first photos-I mostly need to be able to block the extreme sunlight and provide some evening privacy if needed.

Hey There: To be honest, you don't want to put lipstick on - well you know. The problem are the existing blinds, these upper boxes are to bulky and don't go at all with your windows - just change them out with pleated blinds that operate bottom up - top down. These blinds are less than 1 inch in depth and will host as inside mount to each window. The installation is so neat that they appear to be part of the window...furthermore you can manage light and privacy... Check more ideas and projects at www.PleatedBlindsStore.com

Sophie - I disagree. I did not design this. I have no pretensions to being a designer and for many other aspects of the renovation we have indeed had formal plans drawn up. [I also know from experience that having an architect involved is far from a panacea .... but that's another story or stories]. For this room we knew we needed to replace the large leaky picture window and instead of replacing in kind we asked whether it would be possible and reasonable to build a window seat and what would be involved. We showed the contractor many pictures of window seats and shared the required dimension ranges (not exact dimensions) from various articles. He said a bay window would take care of it and no separate plans were required. I include the manufacturer's literature excerpt that says their Bay and Bow windows can be used as window seats. It seemed (and actually still seems) a reasonable solution. Projection Window Bay and Bow windows are like a piece of fine furniture for the façade of your home. These unique windows project from your home, creating additional space that can be used for a variety of purposes, such as a window seat or displaying meaningful trinkets. Our vinyl windows (typically double-hung or casement windows) are inserted into a solid frame to create this unique look that adds style to any home. Bay windows typically have three lites (one central fixed lite and two flanking operational lites) at 20-25-degree angles. Bow windows most commonly consist of four lites, all of which can be fixed or operational, set at 10-15 degree angles. The contractor asked us to describe what we wanted to the window vendor as well and we did. We never used the term bay window. We only talked in terms of window seat. The window vendor also did not dissuade us or suggest we needed an addition instead of a window. The window vendor spec'd the window we needed. Given that we have 8 foot ceilings - this would have been a really good place to catch that a 52" bay window wouldn't be long enough to provide a seat at a reasonable height off the floor. I think that's the key flaw here - plus someone's telling us that (unless I'm wrong) we weren't going to get the wood backing. Tomorrow should be interesting ...