Hi! I'm doing soy candles for the first time and tryed CB-135 with US ECSENTIA chocolate fudge FO (10%) The contaminar have 3" of diameter,. The candle looked lovely: smoth surface and very fragrant. 24h after, I Light the candles ( I make 3 diferent wicks: eco wick 4 ; eco wick 6 (following wick Guide) and small woodwick from 4CANDLES. Wick 6 did made a nice melt pool and the wick 4 also get the edges but not so quickly. The woodwick make the candle tunneling. The scent was perfect and I was confident. After reach a Good melt pool I let the candle burn for about 3 hours. When wax resolidify, There was an awful brown strip on the three candles on the place of the melting pools. Next day lighted the candles again: very poor scent, the melting pool get much more time to achieve but did with wick ECO 6 and ECO 4 and did not with woodwick. The colour of the surfaces get much more dark even. I try the same wax with diferent scents this time: 2 from 4candles and 1 from scent perfique. now I have to Wait 48h and then light then to see what happen. If someone did already face this problem, please help me.

I have been making and selling candles for ten years now. When I started, I was using parafin but within a year I switched to soy. That was about the time they had introduced soy. I use a crock pot. My husband drilled a hole near the bottom, on the side, and put a spicot on it. I melt the wax in the crock pot. I have it set on the dial where it wil heat the wax to 150 degrees. I then pour the amount of melted wax that I want (let's say 14oz) into a glass measuring cup. I then add the scent. Usually about 1oz. It also depends on how strong the scent is, so take a wiff while your stirring. That will be about how strong it will be when the candle is burning. Then I add the coloring. I've tried different ways to color and I liked the liquid color the best but now I don't use any coloring. My label for my jars are the color the candle would be. As soon as I have added the sent and color, I pour it right into the jars.(I use 8oz mason jars) I don't heat my jars first but I do have my wicks already 'glued' into the jars before I pour in the wax. I put a dab of hot glue on the wick tab and attach it to the bottom of the jar. That way it stays centered and in place while the wax is cooling. The 14oz that I mentioned above plus the scent will fill two 8oz jars just right. Once the wax cools, I cut off the wick and put on the lid. I have not had any problems with the scent of my candles. I have repeat buyers. My question to you is what kind of wick do you use. I use a hemp core wick that is already tabbed and dipped in wax to stiffen it. It sounds as if you might be using a zinc core wick. The zinc core wicks will cause alot of the same problems you're having. I tried to use up the zinc core wicks that I had left over from when I made parafin candles and they do not work in soy wax. I was trying to save myself some money but that didn't work. I buy my supplies from Bitter Creek Candle Supply. A link to their site below. I would recommend them to anyone. They have alot of helpful ideas and they do have live help on their site. I don't know what time of day but they usually have someone on there everyday. You can also call them on the phone and there is always someone available. They love talking about candles. I hope this has helped you. Keep trying, you'll get the hang of it. Cindy Here is a link that might be useful: Bitter Creek Candle Supply

The total volume of the jar is not the only factor. The diameter of the jar can also affect your result. Most sites that well wicks have an online guide, to help you choose the right one. They usually go by the diameter of the jar. BTW, if your jars are wide & shallow, you may need to double-wick.

I have done that before too and didn't have a problem with it. As long as the wax temp isn't going above the maximum melting temp (like around 185) it should be fine. As far as the candle frost goes, you may want to take into consideration the room temperature. I have found that during the summer when my home is nice and warm (over 70 degrees) my soy candles cool with pretty much no frosting, but during the winter, I have a much harder time if I don't keep the room warm. Also, you might try letting the wax cool to very slushy and then heat it back up again to 150 and then let it cool again to 100 degrees and then pour. I've experimented with this and it has given me beautiful tops! Here is a link that might be useful: Soy Candle Making Tips and Tricks