I did a restore to a date two days back before I install a USB connected Maxtor 60GB One Touch III back up. I came with an enclosure and I assume it contains a 2.5" notebook hard drive. Strange that could cause the cpu overload, but that seems to be the case. I may try to reinstall, but will run for a while to be sure the problem doesn't creep back in. The cpu is now running most of the time below 10% with some short term (a few seconds) spikes over 30%

I usually have success with direct seeding, so I think that my method works well, assuming that the seeds are good. The soil is usually too heavy and if its overwatered and than dried, it makes the heavy crust on the top, and the seeds often cannot sprout through it. So my method is: 1) Make a row for sowing; 2) Water the row; 3) Mix several handfuls of peat moss into the row so the soil is fluffy; 4) Sow the seeds ( I prefer to soak carrot and beet seeds overnight in the paper towel, it is not necessary for brassicas); 5) Put more of peat moss on the top to cover the seeds; 6) water very carefully but do not overwater. I use small plastic kids watering can. It makes very gentle and slow shower. I water once a day, just one small can for a row and the top dries out during the hot hours but the inside of the row stays moist and loose. Too much watering can displace seeds. I water the tiny seedlings the same way for about a week and then they are ready for the gentle watering from the hose. I think that drip irrigation will be fine too, just do not overdo it.

No apology is necessary. I'm not a forum sheriff or anything like that. Do whatever you like. I'm just suggesting that it's good form (and common courtesy) to write internet forum comments using proper punctuation and proper language. Everyone makes mistakes and misspellings, that's no problem, but cutesy language and someone's idea of humor or clever abbreviations can turn reading into a drudgery. People come here to help and to learn, Unless I see a particular item to be of immediate interest, I personally avoid comments that require more than normal effort to get through. I'd guess I'm not alone with that. Most people will avoid a post in all caps, or with run on sentences and poor punctuation, or colloquial words or abbreviations, or whatever. Do as you like, I'm just suggesting you consider things from a reader's perspective if you make a post asking for help. The various random utilities you have that you found interfere with one another suggest taking a different approach. If you delete all these and install one good anti-virus program, you'll have better protection and no operating problems. Again, do as you like.

a few more things now from last night: (sitting in seat) 1. rh cylinder shows spark but weak, lh cylinder no spark (as far as I see) 2. cranks like no tomorrow and wont fire 3. plenty of fuel in the intake and enough that is splashing up and out the carb while trying to start 4. pulled pulse line off while cranking and fuel pump pulsing as it should, I did not pull line off the engine side yet to verify 5. the spark plugs are wet with fuel and black moist, think its oil but doesn't have oil consistency (fouled already?) 6. fuel is fresh, been thru 8-9 tanks this year already, fuel filter is new, air filter new. 7. governor has been removed, cleaned all ports, cleaned out with wire. 8. spraying start fluid / carb cleaner does not pop engine off. when I move the throttle cable to the lowest setting, the inner carb flapper does not close unless I grab the black dowel on the engine mounted linkages and pop it down manually, then when I move the throttle cable even 1/16 of an inch it pops wide open. The choke does nothing to help the starting, open, closed, doesn't matter. 9. removed engine mounted linkages and tightened but did nothing (still loose to me and when it is to the black down, the linkage bends and wont push it down) last night I got it to chug and then it died and blew white smoke puffs out the top of the carb. (I was holding the governor flap closed with one hand while son in seat cranking Here are my thoughts and shoot holes in it if need be: I think my magneto needs adjustment (I used business card for gap, now I hear loose leaf paper folded in half, I should just get a gap gauge), then I really believe I have a issue in the linkages mounted to engine for throttle and auto gov. I know it works on there own but I have no throttle use, I throttle up or down when engine running and it does nothing. ****if pics of my engine will help I will get them on here asap***