Forgive me but has the betta died allready? I thought it was hanging by a thread. A 25 watt heater will keep the water a consistant temperature. If you go with a heater, do not get the type that is "factory preset" usually a kinda small box looking thing that claims it is good for bowls and aquariums up to 5 gallons. They have been known to fry fish, while some have had success with them, I wouldn't trust it. When it comes time that your bio-bag (I think thats what Whisper calls them)is tatered and shreded, just replace the bag, dont discard the old one, but cut it into pieces small enough to fit in with the carbon, don't replace the carbon for that change but maybe remove some to make room for the cut bio-bag.This will allow the bacteria that has grown on the old one to "seed" the new.-However, what I'm still unsure of is what the "biological" part of the filter is... ---- The biological part of the filter is where the beneficial bacteria grows. Because the bacteria is alive it is called biological.One of the bacterias feeds off the ammonia in the water collumn (from fish crap and decayed food, etc), it. This produces nitrITE,another bacteria that is growing on the filter uses the nitrITE and turns it into nitrATE. This is good, because ammonia and nitITE are toxic to fish, nitrATE isn't toxic as long as its kept at a low level. That is why we do PWCs, to remove the nitrATE that is produced, allong with other dissolved organics in your little ecosystem. Since your aquariumis small needs to be done more frequently, as a rule of thumb. After a while you can determine what amount of water and how often it needs to be changed. One aid in this determination is a complete water test set. In the case of your filter the best place to let it grow is the white bag with the clip. The carbon also hosts the bacteria, but since the carbon exhausts after a while (or gets less effective at its job) it needs to be replaced. Rather then removeing both hosts to the bacteria and leaving no biological filtration, you just discard the old carbon and replace and keep the bag that has bacteria on it allready. As far as aging water, if you are only doing small water changes, frequently the small amount of water you are replacing should not affect the water too drastically. This is not allways the case though some well water(and city) has a high concentration of CO2 in it. This causes the water to be very acidic. When the CO2 escapes'the pH can rise rapidly to a base. This can stress fish, especially delicate ones. I have this situation and I just use an airstone in a bucket of water to "gas it out" if I amdoing a large water change. Aging over night or for a few days will also do the trick. You do however need a good water conditioner, like Prime or Amquel, that removes chlorine/chloramine and ammonia, if you have treated water from a water co----Alagae, with all the nutrients that may have built in the water + ones that are allready there + light 24/7 will give you an algae bloom, no doubt. If you do the PWC's and limit the light the algae will starve and go away. For a quicker results, use no light, or very little for a week or 2. This includes sunlight from a window. Some people have even covered the glass with a paper bag or something for a complete blackout.Read the original link I gave you, its long but no more longwinded then me. Oh yeah, the food varied diet is good, some have had great success with just a quality betta pellet like hikari. If you want to try something else you can even get live brine shrimp from a good LFS or start a hatchery of your own one day, its pretty interesting. My betta is a typical betta, a pig, he'll eat anything.

got any pics? so like it is nice but maybe not what you had in mind. If what y ou had in mind wouldnt work then maybe this is better but you should have been consulted. Take some pics lets see this thing. Mat

When we purchased the current house in 1996, it had the original GE builders grade dishwasher from 1985. It was very loud and didn't clean well, so we never used it. When the kitchen was remodeled in '06 we went with a new GE Profile dishwasher, as we also were buying a GE washer & dryer. That dishwasher only lasted us a year and was repaired several times (rolling racks and noisy water intake valve), but it cleaned fine. We replaced it with an Electrolux Wave-Touch, but only had it 60 days due to installation issues that could not be resolved, through it cleaned better than the GE. We were then without a dishwasher for about 2 years before we got a Miele Diamante Plus in 2009. In the two years that we've had the Miele, it has cleaned everything well. We don't pre-wash, but do rinse some dishes, pots/pans in the sink so piece of food would go in the garbage disposal, but we don't wash them with soap. On occasion, we will soak and hand-wash an item that may have heavy baked-on food, but that's like once or twice a week. Regardless, on the Miele we use the Normal mode or the Pots & Pans mode and everything comes out clean. Only use the China/Chrystal mode two or three times a year. The Express mode we don't use, since it only washes for 5 minutes and then does two 5 minute rinses (we found this 5 minute wash is not long enough to clean a full load). I check the bottom filter once a week and clean it out, but it hardly ever has anything in it.

Is this work being inspected by a building inspector? Does any building code apply in your area? Was a permit pulled for the work? You could take photos to your building office and get their opinion. That could be your "official leverage" if you need any. It can also help with recouping money if you end up in small claims court, etc. In general, if you think you'll ever have to go to any type of remediation/arbitration, or if you think you'll end up in small claims court, your better bet is to always give the contractor a chance to remedy their errors. Some guys simply screw up and they can make excellent repairs. Others are incapable. It appears your man falls into the latter category. If you point out his errors and this guy counters that his work is the best, or if he sees nothing wrong with his methods, then there you go. He's incapable of doing the repair. You don't need to debate him. By him saying there's nothing wrong with what he's done, he's given you the out you need. Remember, "I've always done it this way" isn't a valid defense of not following basic industry standards, or for not following the manufacturer's installation instructions. Were you to simply fire him and bring in someone new, he could have leverage against you. There's a lot of wishy-washy leeway in these things. Depends on what the contract says. If you even have a contract. Depends on what the building inspector says. If you have one. If a permit was pulled. Etc, etc. You have the youtube video. Take more video or still shots showing the methods of construction. Overall shots of the shower, the floor, the drain, the curb. The membrane at the drain and lack of membrane at the curb. If you have empty bags, document what mix was used to pour the floor, etc. You have a 2-part clamping drain and perhaps a CPE membrane. Go to the manufacturers website to see the installation instructions. Did he follow them? No. There are general standards of construction. It appears your man missed pretty much every one of them at each and every opportunity. Good luck!