drilling holes in my rubbermaid?
heidi07
16 years ago
Featured Answer
Sort by:Oldest
Comments (6)
sqh1
16 years agosocks
16 years agoRelated Discussions
The leak in my above-ground Rubbermaid stocktank
Comments (2)Hi frankielynn, The one I'm trying to fix now is a 300 gallon. I had 2 others that were 100 gallons, and had cracks at the bottom, which I couldn't fix. But that was about 5 years ago and I used a glue-type thing. So maybe this Waterweld will work better. I'll keep you posted. Hopefully, it can make it through the summer. Good luck on yours....See MoreCan you drill extra holes into a one-hole sink?
Comments (1)What is the sink made of? Does the faucet have a trim plate that covers the holes? You can get through just about anything with the correct bits. Hole saws are even available with diamond if needed, but carbide does just about everything short of hard stone....See MoreCan I drill a hole in my silgranit sink decking?
Comments (10)Thanks for the help! I just spoke to Blanco Customer Service. There are four additional knockouts for accessories. However, it took half a day, lots of internet searching, a couple of phone calls, one to HD and one to Blanco to find this out. I wouldn't even have known to look for the additional knockouts if you GWebbers hadn't led me in that direction! When I kindly suggested to Blanco that they add this on to the description and make it clear to future potential customers that these knockouts are an option, well, she was let's say 'less than grateful'.."ma'am we have that information on our website". Well, perhaps not every customer wants to go back to the manufacturer's website to try and find that out (model numbers are different from what is stated on the HD site, and in fact she gave me the wrong model number at first...) Anyhow, now I know, I thought I was doing Blanco a service letting them know it was not that clear, and it could be helpful to add that to the HD description..." Ma'am that is HD's description" Oh well, you can lead them to water.......See MoreDo they really drill your faucet hole over the cab?
Comments (32)the time to drill a hole is measured in seconds. This assumes the drill bit is the right one. I think that 99% of men with drills will be proud of their tools and drill as fast as can be done, as long as it's safe. Not "too fast". The drill can turn slow, or slower, or faster. But thinking of a normal hole being drilled in a mere matter of seconds causes a problem. The problem is that this mindset does not slow down the process to include a low-dust result. Getting water to be present = lower dust. the time to drill a hole is measured in minutes, many minutes) if you go slow enough to ensure that water gets into the groove as it is being drilled. Dust is minimized when water is present at the point of contact where the drill bit meets the material being ground down by the drill bit. You might have to back out the drill and go back in. Wasted seconds, if you are thinking of doing it relatively fast. A total waste of effort if you think it's dumb to have to repeat the up and down operation again a mere second later, and again, and again. I guess the only way to get the guy to drill slow is to make him feel pride in reducing dust. This new pride takes time to develop. Lots of talk, beginning early in the day. Like shar-az said in another thread today, sometimes you have to say things more than once. the time to drill a hole is measured in seconds. This is nothing, or almost nothing, when you add up all the time it takes to get to the job site, get set up, measure things out right and do everything else right. So, it stands to reason that a worker holding the drill could adopt the attitude that he is going to do 20 or 30 passes up and down to "go get water" and get water into the grooved notched ring as it gets drilled. It is a hassle if you think it's a hassle. It's a pleasure and a source of personal pride if you think of it that way. It is whatever you say it is. Hth....See Moreheidi07
16 years agoraquibird
16 years agosocks
16 years ago
Related Stories
DIY PROJECTSPocket Hole Joinery, the Beginning Woodworker's Best Friend
Make a wide range of sturdy wooden pieces with just this little bit of know-how
Full StoryDESIGN DICTIONARYWeep Hole
Shedding water and venting air, weep holes are healthy escapes for homes
Full StoryREMODELING GUIDESFinishing Touches: Pro Tricks for Installing Fixtures in Your Tile
Cracked tile, broken drill bits and sloppy-looking fixture installations? Not when you follow these pro tips
Full StoryDIY PROJECTSGet a Grip: Create Handle Openings With Just 2 Tools
Show off your DIY skill by cutting a custom handle opening in a tray or furniture piece, using a drill and a jigsaw
Full StoryDIY PROJECTS29 Home Projects to Make You a DIY Superstar
Patch up holes, turn trash to treasure, erase stains ... these doable DIY projects will better your home and boost your ego
Full StorySTORAGE18 Rooms Made Better With Pegboard
A grid of tiny holes punched in hardboard can be your versatile best friend in every room
Full StoryREMODELING GUIDESDIY: How to Install a Door
Homeowners who aren't afraid of nail guns can tackle their own pre-hung door project in a couple of hours
Full StoryMORE ROOMSIdea of the Week: Driftwood Mantel
Green builders turn black walnut river log into one-of-a-kind accent piece
Full StorySTORAGEBedroom Storage: 12 Ways to Work Your Wardrobe
Instead of letting the mess in your closet overwhelm you, tackle it head on with these smart and simple solutions
Full StoryWOODWORKING5 Holiday Decorations to Craft From Scrap Wood
Give them as gifts or let your own home reap the rewards — these quality crafted pieces will last through many holidays to come
Full Story
squeeze