ekscrunchy - If you upload your photos to Photobucket, there's a box on the right side of the screen that says "Share This Image". You can copy and paste the HTML Code line there into the body of a message and that should bring the pic across - when you preview your message you should be able to see it. Sounds like a great bathroom - I like those Michael Smith tiles! Casey - awesome bathroom - you did a fantastic job! Thanks!

I thought I had a more comprehensive series of photos, but I might have not brought them over when I bought new computers a few weeks ago. The following are not pretty, but they might help: ABOVE: This shows a couple of things I had to work around. High over the toilet is a jog of the vent pipe, it comes into the room because it jogs around a load bearing beam in the wall. Lighting: You see two illuminated light bulbs. Those are the sconce locations for the "new' design. The original design had two sinks, two wall mirrors, and three wall sconces. The old wall sconce locations are the covered up junction boxes. I redid the wiring so there is no live wring in those now unused j-boxes. Outlets: Look at the middle shelf in the closet on the left. In the back right corner you can see a box. I built that to house a couple of electrical outlets. Two outlets for inside the closet, another outlet that is on the closet sidewall facing the sink, you can barely see the cover plate for that box on the closet wall to the left of the drill. More electrical: In the 48" tall cabinet that hides the toilet, there are four outlets in the upper part of that cabinet box. There is one outlet that faces the sink, there is another on the opposite side that faces the toilet. There are two inside the upper cubby to provide power to items in the upper drawer. To protect those outlets, there is a false back wall in the rear of the upper cubby of that toilet cabinet. The cabinet itself is about 32" deep, the false back wall is about 10" out from the cabinet's back, affording roughly 22" of depth for the upper toilet drawer. The cabinets: Nothing fancy, 3/4" birch plywood boxes. Horizontal shelves/tops/bottoms are recessed into the cabinet sides in a 1/4" deep dado. Titebond glue and screws. Cabinet backs are 1/2" MDF, recessed into the cabinet sides/top/bottom. Glued and screwed. Recessing the cabinet backs into the cabinet helps keep the cabinet perfectly square. I typically use a 2" wide vertical stile on my cabinet face frames. I prefer my frames to be flush with the edges of the cabinet sides. With the cabinet sides being 3/4" thick, two of them make 1-1/2". So I'll use a strip of 1/2" filler between adjacent boxes to get that 2" thickness. With my face frames being flush with the inside faces of the cabinet sides, to get square face frames you need square cabinet carcasses. You can't disguise sloppy construction with this method. Toekicks: Under the cabinets you see scrap pieces of 2x4. Those were eventually covered with wood and painted black. They simply limit the depth of the hole under the cabinet to round 8", giving dust bunnies less room to hide. ABOVE: This shows the same run of cabinets with the face frames installed. You can see the electrical outlet on wall of the left closet, facing the sink. You can see the outlet on right side of the toilet cabinet, facing the toilet. ABOVE: Everyone needs a place to keep their "to do" list. I know I'll never lose this list. At least not until I cover it with the teak top. ABOVE: Remember that really small vent pipe that jogged into the room? Well, I covered it with this really big soffit. Nothing like overkill, eh? I actually used it to balance out the visual weight of the upper part of the closet on the left side of the sink. Visually, it centers things to the open area over the center of the sink. Might sound like a lot of silly voodoo design, but visually it feels comfortable to me. The band around the upper walls is backer for the crown molding. ABOVE: Speaking of teak...this is 4/4 teak, or "four quarter" teak. If you go t a lumberyard and by a "one-by-four", it'll be 3/4" thick by 3-1/2" wide. If you go to a lumberyard and order 4/4 lumber, it'll be 1" thick. For 4/4 thickness or less, I'll use one row of biscuits. For 5/4 and thicker, I'll use a double row. In this bathroom the tub deck is 2" (8/4) thick, the sink countertop is 1-1/2" (6/4) thick, and the toilet cabinet teak top is 1" (4/4) thick. ABOVE: I usually use epoxy with teak. I thought I read a recent article that the newer titebond forumations work well on teak, but hey, when you buy epoxy by the gallon, you may as well use it, right? Except that I buy Titebond 4 gallons at a time. Hmmmmmm.... Okay, anyhow, I use epoxy. Teak is an oily wood, so prior to using epoxy I'll wipe down the edges to be glued with acetone. The acetone removes the oils. I mix the epoxy, apply it to the biscuits and the edges with an acid (flux) brush, sap it all together and clamp it up. Biscuits are designed to absorb moisture from water-based glues like Titebond and expand within the cut slots, they really lock the pieces together. Although there is no moisture in epoxy for the biscuit to absorb, it still provides more surface area for the epoxy, plus the biscuits help register and align the teak during the clamping process. ABOVE: After the epoxy has cured. I'm getting ready to belt sand these with 80-grit to smooth it out. Top photo is for the "toilet" cabinet, the bottom photo is a teak window sill for the window behind the tub. So...not the greatest series of "how to" photos. But hopefully they'll help a bit. Mongo

Sorry, left out the paint recipe: I use latex paint in Satin (one was Valspar, one was Sherwin Williams). Both look lighter in the pics than in real life, they're dark cream colors. I mix hot water with Plaster of Paris to make a smooth and creamy consistency, then mix it with the paint. It goes on very nice, and has a wonderful feel after waxing. I don't like my pieces to get too flat or chalky, so waxing is important, as is sanding between coats. I lightly distressed both pieces. I use less Plaster of Paris than most people. I used too much on a practice piece once, and it was like pure plaster, a total nightmare. I did not prime either piece, just cleaned them first. I want to say, I used to cringe in horror at painting old wood, but I'm really liking this chalk paint recipe, and how it turns out. And I only paint if the wood is too damaged for us DIYers to restore. My partner did strip and restore both tops here, the wood grain came out beautiful. We're currently working on a sofa table.....harlequin pattern on the table top. I'll post pics when it's done. :-)

What would be really lovely for a sconce is something with a capiz shell shade and maybe a few lusters, in a kind of art deco feeling to go with the beading on the mirror. I've seen them but can't find them just now. The capiz shell ones are simple and classic. Unlike the extravagencies below. :D Okay, I had to show you this one from Vintage Hardware, which is over the top, but pretty darned gorgeous. I can't decide if this one from Lamps Plus is ugly or wonderful. ...but this one is pretty classic