You have a ton of questions and I will do my best to address them, I also have AADD so if I start to ramble and jump back and forth just overlook that :). We need to simplify this more because there are certain issues you can't change..... being on a slab and the weight issues. Any slab has to be reasonably flat and dry, but in your case it needs to be almost dead flat and dry. We are supposed to always check slabs for vapor emissions that can go unoticed when there is carpet over top that allows the slab to breath and release moisture without any problems. You have an 18yr. old glued down wood floor that has exhibited no problems, in my view that is as good an indicator one is going to get..... so we'll just say you are dry. I don't know how many sq.ft. is involved but it takes some space for an installer to check the slab for flatness and then take measures to correct it. Sometimes a low spot can be a few feet in diameter and with the feathering needed I may need 6', 8' or more to deal with it. If I don't have space I could be featuring up to a high spot underneath furniture. It is best to try and figure a way to go one room a time, clean it out, then go on to the next room. If you have your heart set on an engineered BC, then get it :), life is too short to fret over that as long as you know about this issue and are okay with it. On glued down floors the thickness does not really matter as much as opposed to floating. What does matter is the top wear layer thickness and using the right adhesive. A 3mm or 4mm thick wear layer is actually better in the long run as a 5mm thick . Going too thick with the wear layer can cause a phenomenon called "dry cupping" .... the NWFA and NOFMA are aware of this and it is being addressed. If you go with a glued down engineered wood floor and want to put on a sealer as "insurance" , then do it. In your case I would strongly consider using Stauf 960 which is a quality sealer and adhesive combined in one application. You pay alot more for the adhesive but you only have one labor issue. Imo you could also go with a floating floor. But to pull this off you must use a quality product and (here I go again)..... the concrete must be flat. There is a laminate out there that I have personally installed that is almost bullet proof. That would be Wilsonart , which is a high pressure laminate referred to as an HPL. Putting that down along with using their blue fusion glue in the joinery can take any weight you want to put on top of it. When I do that I recommend to the client upgrading the underlayment to a product Sound Solutions. You cannot walk on this type of install and tell that it floats. You could also go with a floating engineered wood... this is where thickness comes into play. I prefer to use nothing less than a 1/2" in thickness and a where the joints get glued up, or, choose a good reliable click-lock system like the valinge or Uniclic joinery systems. They both hold together well. The wood should also be waht is called balanced.... the top layer equals the bottom. You are very typical of alot of my clients. Quit stressing so much :).

Hello! This is awesome information, thank you all so much!! ttodd - so you used fabric glue instead of sewing? Was it messy? Do you think it will hold over time? I was thinking of sewing it as I have never used the glue. charlieinnj - wow! That looks great! I'd like to try this as well. Sleek/comtempory...yes this is exactly what I am going for. Yes, the quilt wall hanging may not work! LOL! I'll have to break that to dh. Ok, about the fabric repeating exactly...I wonder if one 84" or 96" curtain panel will be enough fabric to accomplish this? This is a curtain panel that I found, not fabric. blondepegasus - yes, I will have the yellow ribbon on the curtains, the yellow in the fabric wall hangings, yellow pillows on the chair. I'm so excited to get started on these projects!! Thanks!! Elaine

Since the room is large and bright -- perhaps a deep chocolate brown would make it more cozy -- then add LOTS of lime green accents (like your storage box and waste basket) Find a bright green and white fabric to cover the new "inspiration" board ..... Check out: Benjamin Moore - "Mink" -- #2112-10 Benjamin Moore - "Taupe" -- #2110-10 Both of these are rich deep colors and would work well with the accent tile in the cork flooring.

I would do this -- not having bright light behind the screens will be much better for his eyes, and he still has the pleasure of the open view by just glancing to the right. If the tall cabinet (with art) doesn't fit I woud just swivel it around to face the desk, keeping it in that corner. I'd keep that art where it is and put another piece (in either case) on the wall to the right. I recommend adding drapes, or at least drapery panels, to make the room look complete.