As others have said, a drying agent, like Jet Dry or Rinse-Aid, is a must. Running the hot water in your sink before starting the dishwasher so that hot water is in the pipes as the dishwasher begins to fill. Finally, cracking open the door once the drying cycle is complete helps as well so that the steam can escape. I've had a Miele since 2015 and, at the time after reading reviews, the reason I purchased it was because it automatically cracks open the door at the end of the drying cycle. I've never had any drying issues with it. At the time it was the only dishwasher that opened the door automatically but I believe more brands do that now.

Timely post-- I just discovered ANOTHER crack in the plastic housing of my Bosch dryer. That makes FOUR different times that one of the two machines has cracked. REALLY BOSCH, this is unacceptable. BTW does anyone else find the spin cycle lacking unless it's on MAX? I don't recall it being this bad when I first bought it. But now, I have to give things an extra spin before tossing them into the dryer. DH's nice new sweatshirt was stained at dinner. I immediately washed it to remove the stain. As it was quite costly, I wanted to handle it delicately. I tried to tone down the spin cycle and ended up with a sodden lump. I had to re-spin on Max to have it dry enough to drip dry. Not happy...

Since I last posted, I've narrowed a few things down. One of the rooms that was affected (there were 2 rooms total), has been fixed. The french drain I installed around the perimeter of the front of the house, where water was creeping under the foundation, seems to have fixed the issue in the larger room. There is now no more musty smell in there. However, the other room, which is a "closet" that backs up directly to a bathroom, still has the odor, which has actually gotten worse. The smell is definitely partially sweet, and partially musty. I've cut the drywall all the way around the room to see if there is any signs of water damage, dead animals, etc inside of the walls. Interestingly enough, the inside of the walls that butt up to other rooms, smell fine. The walls that have concrete on the other side, have the odor present (perimeter walls). The only two things I haven't addressed yet are the roof (I'd have to cut the ceiling open because there is no attic access at this point for how low the roof pitches). The other thing would be the foundation (slab). I have fairly expensive laminate flooring and underlayment in that room, which would have to be removed, and the floor would have to be inspected for dampness. However, given the circumstances, it's been narrowed down quite a bit. The room has 4 walls (2 butt up to exterior concrete and 2 others butt up to interior rooms), a standard hollow core wood door, a West-facing window, and a drywall knockdown ceiling. There is only two piece of furniture in the room, which are bookcases. One is MDF (still wrapped in plastic to hold it together before I bolt it in), and the other is pine wood, also wrapped in thin plastic to protect it. I've just put two large shop fans, a big air purifier, an ionizer, and ozone generator all in the room with a big bucket of damprid (although humidity levels in that room are only 49% in south florida, which is fairly average). I've also sprayed half a can of lysol air spray into the room. I'll let you guys know how that works out, and hopefully we can figure it out. and ESMAN - let me know your notes as well. Thanks.

Please allow me to post my opinion and experience on this stinky issue. I am the owner of a HE3T washer, and I am really unhappy with it, mainly because of the smelly and moldy issue, that crept up on us unexpectedly. My wife and I have 4 kids, so doing laundry is a daily affair, and not to be underestimated or procrastinated either... I am on the verge of throwing that ugly beast out of the laundry room for good. It is unbearably revolting to pick up an (alleged) clean towel to dry one's face just out of the shower, and "smear" moldy smell all over you. The vomit factor is very high on this one.... :-( However, I want to highlight a point, and that this issue is NOT an issue with ALL the FL (front loader) washing machines in general. Maybe just US made ones... Overseas, ( Italy ) where I grew up, FL are 99.999999% of laundry machines available on the market and this issue is completely unknown. To put it simply, I am now 45 years of age, I have lived in Italy 28 of those years, and I have never, ever, seen or heard of moldy smell on clean laundry out of the washer. Never. If you knew my mother (she redefines the word "neat freak") you would understand. Just the hint of a remote possibility of having mold in the washer and/or laundry, would bring that washer in the front yard in flames... Seriously, I believe US manufacturers have gone wrong somewhere in the making of this machines. They either cut one too may corners ( quality of rubber, maybe ?) or are attempting to reduce the amount of water in the cycle at the point where the quality of the rinse cycle is not an issue with them, and us as consumers are not part of the equation. I just came back from a one year of living in Italy with wife and kids, and the FIRST thing we notice, ever single time we go over there, is how much fresher and overall incredibly better smell of "clean laundry" they have from their washers. I know, we are weird... and on the contrary, as soon as we are back to the US, and to our $#@! HE3T, we pick up the moldy smell again. The customer/user/consumer SHOULD NOT have to do any gimmicks or use any "special" tablets, in order to operate these washers, or any washer, for that matter, NOT A SINGLE ONE. This washers are NOT cheap and they should just... well, work. Living in Italy for the last 12 months, we used two washers, one that came with the apartment we rented, and besides a slower spin cycle, it worked as expected (put dirty clothes in, put detergent, push the button, wait, get wet CLEAN laundry out, END OF THE story. Then the landlord needed his washer back, and for a "rent discount" he took that one back, and I got my old 12 years old Miele washer out of storage. This Miele has a somewhat smaller load capacity than most, and it worked for a family of 6 for a long time. Same for my mother's Candy ( Italian brand), and my sister's old Italian washer (San Giorgio). That one lasted 16 years of day in and day out operation for a family of six. It is just so frustrating, since I know that as a concept, FL do work very well, I have seen it work for decades... and one more time, we should NOT need to use "tablets" or do complicated procedures to have clean and good smelling laundry. As I said before, millions of people overseas use FL day in and day out, without doing anything else other than 1) put dirty laundry in 2) select cycle 3) put detergent in 4) push button 5( get clean clothes out. End of the story. Kenmore, Sears, whatever, get your acts together !!