You are absolutely correct, Generally the excavation is the difficult & expensive part of your repair, but you seem to have that under control. Now as we discuss the plumbing part of the job allow me to give you the correct trade nomenclature so you will be on the same page with your plumbing suppliers and inspector. Technically speaking, what you are working on is not a drain line, it is the "House Sewer" line. Code requires a main cleanout within 3ft of the point where the house sewer enters the structure. In the case of slab construction it would be found outside and approximately 3' from the foundation. For houses with a basement the main cleanout is generally just inside the footer wall and for houses with a crawlspace it can be inside or outside the footer wall. The line from the main cleanout to the septic tank or municipal main is defined as the house sewer while the main line inside the house is defined as the "House Main Drain". This is important to know because the codes allow different materials for each type of line. The raw cut end of a pipe that has no threads or fittings is called a "Spigot end" or simply a "Spigot" The formed female end of your pipe is called an "End Bell" and pipe which has an end bell on one end and a spigot end on the other end is called "Hub & Spigot" pipe so that glazed clay pipe that you have is "Vitrified clay hub & spigot pipe". It was generally made in 4' sections and when laid, the hub is always placed on the upstream end. While it can be done, as a general rule it is nearly impossible to cut that type of pipe without breaking it. (I have made & attached an illustration to help you understand the text.) To begin your project excavate until you find the end bell on a section of pipe downstream from where you want to install your cleanout. Fernco makes a rubber donute gasket that will fit inside the hub of that clay pipe, then your PVC will be inserted into the center of the Fernco. (make sure the Fernco you buy is listed as "Vitrified clay x PVC") If you can not find the correct Fernco some jurisdictions will allow you to pack the joint with "Oakum" which is a fiberous rope looking material that is impregnated with tar. To install the oakum you wrap it around the pipe and push it into the joint with a broad screwdriver, packing as tight as you can. You can make your cleanout with a Wye & 1/8th bend (sanitary 45deg elbow) in the manner you describe, but what you are making is a running cleanout and in some jurisdictions they require a running cleanout to be installed to the line can be snaked in both directions. The preferred fitting is a "Rodding Tee" sometimes called a "Cleanout Tee". An ordinary sanitary tee has a radius towards the downstream direction of flow, but a Rodding Tee has a radius in both directions. In some jurisdictions if they require a bi-directional cleanout and if you use the Wye & 1/8th bend method you actually have to make two cleanouts, one in each direction. Also not that the one for snaking in the upstream direction must be installed on the downstream side of the downstream cleanout. That is to insure that you can snake the complete line. If they were reversed you could not snake the space between the two cleanouts. You then continue your new PVC pipe to the Spigot end of the vitrified clay pipe on the upstream side of your repair and connect the PVC to the clay pipe with a Fernco coupling. (Careful here. Although both the clay pipe & the PVC are 4", that is the ID of the pipes, but because the clay pipe wall is much thicker than the PVC pipe a common 4" Fernco won't fit. Make sure you get a Fernco coupling that is listed as 4"PVC x 4" Vitrified Clay. (Although I have on occassion found them in Home Depot & Lowes as a rule you will probably have to go to a real Plumbing supply house to find the correct Fernco's) Now to answer your next question, how to cut the PVC. You can easily cut PVC with a hacksaw, a PVC saw or what I prefer for cutting 3" and larger, a common hand wood saw. Here is a tip when cutting pipe with a saw. After you start your cut, when you are about 1/4 of the way through the pipe, rotate the pipe a 1/4 turn, cut down another 1/4, then rotate the pipe again and finish your cut. Rotating the pipe in that manner will help keep a straight cut line on the end of your pipe. Sand is the preferred material for bedding the pipe and continue covering with sand until you have a minimum of 4" on top of the pipe, then you may use "Clean fill dirt" that is free of rocks until you have 12" above the pipe. When you finish backfilling it is best to have the top about 3" or 4" above grade to allow for settling. One a side note, the first clay pipe you found was 4" clay tile that was just laid end to end with no seals around the pipe, then it was covered with pea gravel. Back in the days before perforated poly or PVC they used that method to make leach fields or to install storm drains. The little gaps between the sections allowed the water in the pipe to leach into the soil the same way that modern perf pipe does.

What I've been told for my area is that the sewer pipe running to the street enters the house at a point parallel to the incoming water line, but under the basement. I also assume it runs directly from the entry point to the main soil stack. Using those two points I have a fairly good idea of where the main sewer pipe runs under the basement floor. My approach would be more complicated if I had multiple soil stacks, since I wouldn't be able to see how the lines fit together under the floor. Bruce

IF you are not equipped to chip away sidewalk concrete, and IF you need a patch that will be good for only a few years, you can sleeve the break INSIDE with a piece of PVC with a wide enough slit in it to allow it to close/compress down just enough to slip inside. Glue it to death. Keep in mind this is a ridiculous patch but it's one that will work, especially outdoors away from your house. Secondly, if I read this right and can assume that a 4" drain is huge for your pump, you could dig into the lawn just a little bit, reduce the outer lengths of the sump line to a 3" pipe, shove a 3" pipe into the broken sidewalk tube, and Bob's your uncle!

Will try again with pictures. I dug down so that a brick could be put under the pipe and the pipe would be below the level of the sod. Outward to that I lay two bricks side by side against the fist brick to expand the floor. At the end of those two bricks I laid a couple of more bricks so the floor is about 3 bricks long. Starting at the pipe I laid a brick on each side of the pipe, creating a walls around the first brick, I laid two more bricks to create walls for the two floor bricks, so that the spill way expands as it gets further from the pipe. I just left the last bricks to lengthen the floor without walls. This is a work in progress and it has been so hot I have not mowed the yard in a week, but I think you can see what the intent is. As you can see in the second picture it is nearly invisible. and completely disappears from the house. (No comments on the quality of the grass. It is green and I have worked hard to get this to grow in the Carolina clay. ;-)