Thank you all for great info! Wolf's cold spots in the middle is a little bummer. I wouldn't expect this kind of design on 5 way bridge cooktop. The elements suppose to be made by French company Jaeger Hiflux. Their Crescendo model is quite different from what I have ever seen in induction cooktops. Check this out.. http://www.jaeger-sas.com/#!induction-en/cl7w Anyway since Wolf has no flex in bridge mode then we might take another look into 36" GE Cafe model which was #3 on our list. It has only one no flex bridge mode, but it's much cheaper than Wolf or Miele. That model has many positive reviews including #1 on CR rating (99 out of 100). On both GE & Wolf we like simple, clean interface. GE is better with 17 vs 10 levels on Wolf. On GE minus side is power sharing (not quite sure how much problem is that in real use) and only 1 year warranty vs 3 year on Wolf. However much bigger problem on GE Cafe is SS color. My DH says that specific color is clashing with our choice of Silestone Kensho countertop (light gray). I don't see it as bad but we might loose it on that argument. No question the decision between Miele vs Wolf vs GE Cafe is giving us more headaches than any other appliance.

So far so good cand. It's my first time on induction so I'm more focused on the induction itself as opposed to the Miele vs another. I've mainly been using the big hob on the right, as Chanop says. I haven't used the bridge or the timers yet. I also need to turn on the half step power settings. The hobs are definitely spread out enough to allow 3 bigger pieces of cookware at once. One thing I will note is that the burners are kind of set back from the front of the cooktop, more so than any range/cooktop I've used before. Perhaps the exhaust hood makes it seem even more so but only the front part of the bridge and the smallest hobs are near the front of the cooktop.

I bridge two hobs for griddles. I have not cooked with a large non griddle pan on the 4 hobs bridged together. I did put my very large griddle over the 4 hobs bridged together and after it heated for a while (it is carbon steel) it worked fine for pancakes. You will get a “dead” area in the middle of the 4 so how well it cooks will depend on your cookware (how it conducts the heat) and what you are cooking. Someone posted a photo of what the wolf hobs look like under the hood and they were not circular but octagonal if I recall correctly so the dead areas are minimized. If you can get to a wolf showroom or other design center that has wolf I would try it out. Were you considering the Thermador Freedom? It says max cookware size 13X21. I would think it could accommodate two 12” pans - again find a showroom that has one live and try it out.

@r, I thought I would chime in here to just say that I don’t think you are “obsessing“ at all regarding the use of knobs in this case. One of the most crucial variables in any kind of industrial design is the way we interface or interact with whatever the product is. Most of us utilize capacitive touch controls or infrared type touch controls on a constant basis with everything from iPads, smart phones, as well as any number of house appliances. But I would suggest that your instinct regarding cooktop or rangetop controls makes a lot of sense. Consider the difference in using a wall oven versus a cooktop. Most cooks in the kitchen can get the opportunity to wipe their hands in order to use touch capacitive controls on a wall oven. Of course, the case could be made that turning a simple dial, can be more intuitive, then going through a series of menus to get to where you want to go, since in the end, the mission of the wall oven has not really changed very much since our grandparents time which is essentially to bake the cake or roast the chicken. The reason I suspect that cook tops and range tops, as well as ranges are a particularly good candidate for knobs is due to the fact that the controls are often placed on a horizontal plane. Many people, especially those who are new to induction appliances for example, have learned a hard lesson as the very sensitive touch controls do not always take kindly to steam, water, droplets, and oil or gravy splatters. It is not hard to imagine why this is problematic because if you put any of these liquids on top of your smart phone screen, you would discover that the touch controls that works so beautifully such as the ones I’m using right now on my iPhone to create this post do not take kindly to having these substances on top of them. There are lots of examples of folks who have touch capacitive controls on these horizontal locations where the entire appliance is either shut down or thrown off its game. Of course, the majority of modern products that have knobs do not use the analog/mechanical controls of knobs of the past, but are in fact, “knobs“ that interface with micro control boards behind them. Still, there is an entire field of design that studies user interaction, and I do think that, at least, in some instances, such as with cooktops, knobs actually, do make a lot of sense. One can certainly debate where the best location for those knobs would be to avoid getting splatters on them since Cleaning knobs is not exactly, a fun time for most folks. Some people would assume that installing Touch Sensitive controls in all sorts of consumer products that once used knobs, levers, and buttons, is simply a design trend, and I’m sure there is truth to that. But a little voice inside also suggests to me, that one of the reasons they have moved away from knobs and especially the electromechanical kinds used in the past, is due to the cost of manufacturing. I do not have a data set to support this theory, but if you consider the labour and the bewildering amount of copper wiring that went into something such as a 1950 electric stove, some of which had lots of extra features, you can begin to imagine the cost savings of having a micro “motherboard“ taking the place of all that complex analogue electrical structure. I truly enjoy all of the benefits and possibilities that I have with my smart phone, laptop, iPads, etc. But I do think your instincts for knobs are not without merit, because sometimes, appliance designers attempt to answer questions that no one ever asked. My two. Cents 🤔.