Sooooo glad to run across this, used bar keepers friend on a dry toothbrush and just a few rubs and it came out, perfectly!! My stains were like train tracks across both legs from throwing the jeans over a the rail on my stairs to dry. have done this 100 times, no idea why it stained this time, but the bar keeper's friend got all of it out.

My FL Samsung 338 spins at some 1300 RPM and my clothes do not end up in a ball up knot or wrinkled mass at the end of the wash cycle. In fact, my clothes are less wrinkled with this W/D set than they have been with any set Ive used. I could wear my clothes right out of the dryerÂbut I suffer from OCD so I iron everything, including my sheets, before I put them away. My experience thus far with the Samsung is very positive: gets clothing very clean; extremely quiet; gentle on my clothes; large capacity; offers many wash options including a warm rinse cycle, a steam clean, a quick wash cycle of 34 minutes and a rinse only option. It has a delayed start so I can load the machine at night and have a load ready for the dryer as soon as I get up in the morning so I get a jump on the laundry chore. The steam clean really works to get out stains. I thought it was a gimmick until I tried it on a bunch of towels that a full container of cola spilled on; it happened during our move when we were without a W/D for a week. Not only were the towels stained, but very stinky. I didn't expect the towels to come clean, but the steam feature got both the stains and the smell out. It also has brighten up my whites (I can't use bleach due to allergies and psoriasis) to the point that my husband actually noticed. I donÂt like to dry my clothes bone dry and this dryer allows me to dry my clothes to the point where there is just a tab bit of moisture left in them without my having to babysit the machine. All I have to do is lower the temperature on the machine to med low and set the timed dry to 40 minutes and the clothes come out just like I like them. Just a note on delivery: whatever brand you decide on, if you purchase pedestals just be adamant with the installers about NOT turning your machine upside down to install the pedestals. Some manufactures are now starting to go after the dealers about this; nonetheless, many dealers are still turning the machines upside down to install the pedestals because the machines are very heavy and itÂs more convenient to install the pedestals this way. Some installers will try to tell you itÂs ok to turn the washer upside down with the shipping bolts in placeÂnot true. Turning the washer upside down can damage the tub, knock it out of alignment, or other damage can occur in the process as the machines are very heavy. Even after the Samsung rep went to my local Lowes and told them to stop turning the washers upside down, the installer tried to tell me it was okay for him to turn the machine upside with the bolts in place. When the installer turned my dryer upside down, I made him take it back to the store and I called the Operations Manager for a little talk. (I stopped him before he turned the washer upside down. I made it very clear that if I am paying for the W/D, no one was turning anything upside downÂand I donÂt care if SamsungÂs rep said it was okay to turn the dryer upside down. A new dryer was sent out and it was not turned upside down. Bottom line: your money; your machines; you have a right to have the machine properly handled.

@slogan3561 The cotton on the market today is fine. We have Mele washers and whites come out white. Keeping them white means you need to have the following: 1. If your water is hard (lots of minerals) a water softener should be used. 2. Heavily soiled whites should be pre-treated and soaked to loosen soil before the main wash. Use the washers soak cycle or a pre-wash. 3. A good detergent with the proper amount. Not the cheapest thing you find on sale. 4. A good Oxygen bleach. Make sure to use a water temp of 140F (60C) or higher to get the maximum effect from the oxygen bleach. If you have a clothes line, use it. The UV light from the sun works great to bleach whites and it's free! Many of today's washers are not built with the consumer in mind. They are built to get the maximum rebate from the government for their eco-friendliness.

Yikes - i gotta go (have my coat on, I don't know why I checked back after emailing Y about DD's dance class tomorrow). Merillat mentioned sanding sealer that is only used when sanding soft woods - it stiffens the wood fibers so you can sand smoother. Not usually used on oak. Sealcoat is a "sanding sealer" b/c it can be used that way but really I don't want you to sand the veneer much at all. I am telling you to use it (if you want) b/c I found it made the oak a little smoother w/o totally filling in the grain like a grain filler, and it is harder than poly, will make the finish more durable than poly alone w/o putting on lots of thick (multiple thin coats) poly. you thin (and clean) shellac with denatured alcohol. You can let excess dry in container and then throw it out. Rags can be thrown out (in small quantities) when thoroughly dry. Sealed in water you'd have to check with town about hazardous waste (same with leftover stain, paint). That's why I have multiple cans sitting in my garage LOL. Clean the shellac brush by pouring alcohol into clean PB jar, swishing the brush around - you can pour the cloudy shellac into your metal can with lots of water for disposal, or pour it into another container and let it evaporate. Pour more alcohol into jar, swish until clear. then wash brush in mild soap and water, hang bristles down to dry. It may dry a *little* stiff, but you should be able to soften it by flexing bristles with your hand. if they "crack" rather than flex, you've still got shellac in the brush and need to clean with alcohol again. you *can* just stain and apply the polycrylic if you want to, straight out of the can I'd do 2-3 coats (which may end up looking plasticky but you can try wiping off the last coat like I did on my island trim), if you use the wipeon stuff you'll need 6 coats minimum, and you're *supposed* to sand b/t coats to get it to stick so I'm really leary of telling you to sand that much. You can do 1 coat of regular Sealcoat over stain, sand *lightly*, then 2 coats rolled on poly (barely sand b/t coats). That *should* be enough protection - at least until you have kids and they kick their feet against the island LOL. I'll check back after 1 pm.