I have not had any problems on my jobs, but I am very particular on the substrate being flat and adequate expansion space left.

Wood vs. Engineered Wood? No contest in this case. If the home was built in 1905, put real hardwood in. This preserves the integrity of the home's building materials. Plus, as you can see from the age of these floors, higher grades (i.e. thicker) hardwood can be sanded several times; you usually don't get even one chance to sand engineered wood. The hardwood layer at the top of this multilayered product is simply too thin. Level Floors and Subfloors There are ways to level a subfloor, ranging from replacing parts of the subfloor with thicker or thinner sheets of plywood (or planks, see below), to pour-on leveling compounds that harden to make the entire floor level. What you use to level uneven areas depends on what the subflooring is. If it is plywood or concrete, the compound works. But more likely with this home, on floors at or above grade, there will be wood planks laid at a diagonal across the floor joists. So in your home, the layers were probably joists first, then subfloor planks of wood, then hardwood with tongue & groove joints. You cannot effectively use a pour-on leveling compound on a plank subfloor, as there are cracks between the planks. However, you can lay a new hardwood floor directly on a wood plank subfloor as long as those planks are sound and relatively level. Replace individual planks that have been damaged by water or insects, are otherwise compromised, or even missing (it happens!), with either new planks of lumber, or with plywood of the same thickness as the planks. Any lumber you install, for either the subfloor or finished flooring, should be brought in to your home several days prior to installation, so the materials acclimatize to your typical interior temperature and humidity. Unlike for ceramic or porcelain tile, the subfloor does not have to be perfectly level. And unlike vinyl sheeting, planks or tiles, the hardwood won't "telegraph" minor differences in height, and minor surface irregularities, so the subfloor doesn't have to be absolutely perfect; it should be sound, strong, uniform and essentially level. Your flooring contractor can give you specifics on what upgrades your subfloor may need once the original hardwood is removed. Joists If the floor is significantly not level in parts, or if certain areas feel spongy when you walk on them, I recommend you have your flooring contractor, a home inspector, or structural engineer inspect the subflooring and especially the floor joists. You don't want to invest in a new floor, only to have it become damaged because some joists weren't attended to. Transitions Transitions (a.k.a. thresholds or molding) between existing rooms and the new floor ought to be made of the same wood and same finish (stain, polyurethane, etc.) as the new flooring you are putting down. As wood ages, the finish becomes darker, so trying to make the transitions match the finishes of existing floors is very difficult and not recommended (what will match those floors right now won't match later after your transitions age up a bit). Eventually, the transitions wouldn't match either the new or the old floors! Transitions come in four types: reducer (when the two floors being joined are of different heights), seam binder (when the floors are the same height, and the boards from each are very close to one another), T-mold (when the two floors are the same height, but there is a crack between the two rooms' flooring) and stair nose or stair edger (when the flooring needs to curve around the front of a stair's "tread"--the flat part of a stair upon which you tread!). The transitions for your particular project can be ordered when you order the hardwood, so make sure to include measurements for those doorways/entrances. The contractor can tell you if he/she anticipates there will be a height difference or gap between the floorings, which would require those particular transitions. Dry Air Concerns Consult a local lumber supplier or flooring contractor familiar with your local climate conditions to discuss finishes or other tips for keeping your wood floors healthy in the dry winters. Sounds wonderful! Have fun!

Choosing the right flooring type isn't enough for your living condition. You will have to consider the types of cut: flat sawn, rift and quarter sawn, quarter sawn or live sawn. Quarter sawn and rift & quarter sawn will be best choices, because expansion and contraction is along the thickness of the wood. You will need climate control all year round. 70 degrees at 40 % relative humidity is where you want to be throughout the year. The use of a humidifier/dehumidifier will be needed year round. Although, engineered flooring is more stable than solid. Using the wrong wood specie in your living condition can run the risk of de-laminating with engineered wood. If, the top veneer is more or less stable than it's core and backing. You will experience de-laminating in extreme humidity swings. Take in account of what the engineered flooring is constructed of: mdf or plywood. The width of the flooring will account for how much expansion and contracting also. 2 1/4" strips are the most stable. As you go wider, expect to see more wider seasonal gaps. Proper acclimating is critical, should be performed with a moisture meter. For 2 1/4" strip flooring , sub-floor and flooring moisture should be within 4%. For all other widths 2% moisture differentiation is allowed or should not be exceeded. Don't forget proper expansion gaps, which is the thickness of your flooring, example: 3/4" thick = 3/4" gap. Sub-floor type and condition will affect the performance of wood floors. All this needs to be considered for the proper and successful performance of your wood floors.

I'm not a fan of click together engineered hardwood. This is not something I would recommend - especially in an uncontrolled environment like a cabin. The click edge is the part that holds everything together. It turns out a plied wood click edge doesn't have a lot of holding power. In fact it down right fails 99% of the time. This is why you are having a hard time finding a plied wood centre. The fibre board is much stronger for a click edge. That's why it has been used for decades with laminate...and some who wish to use hardwood on top. I don't recommend that one...but it's your choice. Hardwood has a very specific way it expands/contracts. It does this across the grain. This is VERY different from the fibre board. Fibre board moves in all 6 directions (yep...6). The more swings you have in humidity and temperature the greater the movement the wood is going to do. And the fibre board will also be moving but in several OTHER directions as well. Oh dear. Now imagine a home that is NOT climate controlled. A cabin for instance. Imagine the wood and fibre board are happy with each other at 20 C and 40% humidity. Now winter comes and we have -10 C and 15% humidity. And then summer comes again and now we are at 35 C and 65% humidity. It is highly possible your wood surface will have peeled off of your fibre board centre. The wood moved in a different way than the fibre board and they tore themselves apart. With your price point, you are better off getting a very narrow plank hardwood (2" or so) and have it laid and then site finished. You will still pay around $4/sf for the wood and $3.50/sf for the sanding/refinish but it will be a floor that lasts. It will still move and twist and shrink and expand. But it will do it in such a way that keeps the floor functional. Or go with an SPC/WPC vinyl core and enjoy your cabin.