This old thread got revisited. @dani_m08 to answer the question about extra probe, I believe I ordered an extra one when I bought the set up. The probe wire is just setting in the junction box I think but honestly I cant remember. When I laid out the underfloor heating and the probe, I just ran another probe near the first probe, and it was then sealed into the floor self leveling compound as per instructions. then the end was just threaded into the wall like the one that would be live, and not connected, but just laying there in the box. Regarding the tile layout. I just decided to run it this way, after getting instructions on the 90Degree way, IIRC. The herringbone that I love is from my childhood and the side walks in my neighborhood that all ran at 45Degree. so that to me is herringbone. I know you posted on @sochi thread about her amazing bathroom and a wall mounted faucet. I would totally do it if I had the right sink for it. In my case I had made my sink out of soapstone and an integrated backsplash. The pictures of this bathroom reveal are no longer available because of the use of photo bucket, when it was Gardenweb. I did not keep my account with photo bucket. I'll add some of the reveal pictures so you can see the sink and floor. Regarding the sink there is no ledge for water to drip from my hands when using the faucet. The water drips right into the sink. In my other bathroom with a deck mounted faucet I am always wiping up drips and it is a nuisance. I much prefer the setup for this sink. Below: I love the flush finish from the faucet to the bottom of the sink. nothing drips on a counter or edge of a sink. Below: looking in from the doorway. Below: Here I am finishing up the sink. the backsplash was epoxied on as a separate piece. The whole soapstone install in the room took next to nothing to buy as they were all small pieces that I epoxied together with a 3 part stone epoxy. Below: this is the counter at the tub, and is in 2 long pieces but I was able to epoxy them together at there edges to make a wide slab for the top. All the soapstone was finished with a 60 grit sandpaper to be rough and this lovely soft tone of blue/green/gray/white. I did not oil it so this color tone would remain light. Below: If I recall correctly @sochi helped me decide on this Hubberton Forge Mirror. I have 3 different metals in this room, but they are all a cool silver to black color. Below: the center of this tower shares space with the kitchen on the other side of the wall. there is also some extra space that houses some electrical wiring. this is an old simple house. this bathroom was an add on when it got move to the farm in the 30s IIRC. The plumbing was all rearrange and some of the details that were orignially there I kept but updated it, such as this tower feature. The old one went and the carpenter did a wonderful job with this one. Below: This feature was another thing I kept from the old bathroom but flipped it from the other end and had the carpenter put drawers in it. Before it was a hell hole. things got lost and the build was soooo old and creapy I didn't like using it for storage. Now it is perfect for storage.

I had the exact same problem. I picked out the vanity I wanted but did not think about the fact that it wasn't made to sit flush against the wall. I spent a month looking for something else, but in the end we decided to go with something shorter and have it not be against the wall. But we were going from 72" to 60" which is probably not workable in your mom's situation. I did find a lot of vanities that did have flat sides and could work in a corner, if you are willing to have the countertop fabricated. They just need to not have any trim detail on the top or bottom like the one you picked out does. I would just look at the ones without the pre-made tops. Because the pre-made top will still leave you with a slight gap because of the countertop overhang. This is an example: Avanity Modero which is sold everywhere, not just at Lowe's. The cabinet we ended up buying is an Avanity Madison which won't work for you, but I assume it is of similar quality. We are pretty happy with it. The drawers and doors have soft close but I do feel like the glides in my Ikea kitchen drawers are better quality. It is very pretty and I wanted a stained wood so I am really happy with our choice. If I had been willing to go with a painted finish, I think we might have stuck with the 72" Modero.

I like pebble tile, but I do not like THIS pebble tile. I think I'm reacting negatively to the blue tones ... and to the mixed tones. I think pebble tile should be more natural looking, soft and soothing, and a nod towards nature. This mixed-tones pebble tile looks a bit jarring, and I do not like it. Regardless, I suspect hex tile is a better, more long-lasting choice. As others have said, more tile /less grout is a more user-friendly choice. And I think pretty much everyone likes hex tile -- it's kind of a thing that exists outside styles and trends. Having said that, I am considering pebble tile for my upstairs bathroom. I have the most perfect set of inspiration pix, which include pebble tile in the shower only ... but Practical Me is telling me to use the inspiration pix ... but sub in something else for the pebbles. Also I don't find the pebble floor that comfortable for my bare feet. You can get real pebbles -- round pebbles just like you could pick up from the ground -- or you can get "flat top pebbles", which have been cut so that the surface is flat. This gives you the look of pebbles but a comfortable feel.

Why aren’t you telling him “NO”?