"I could also just get a pull-down faucet for the sink and aim it at the tub to fill it." You could - but you won't like it. The most one of those will fill is 2.2 gallons a minute - some less that that. Divide your tub's capacity by that and you're looking at 20 minutes to fill +/- Not good. beekeeper - I have one of these and have placed more than half a dozen in projects over the past few years. What you get for your money is a machined brass body that mounts in the ceiling or wall and a plated trim piece. The body is a substantial piece of hardware and chrome,brass, nickel plating costs $$$ too. Whether that's all worth 500 + bucks, is up to you. Like davidro says, it doesn't matter what the delivery system is, this is just an opening for hot water to come out of, albeit one with a bit of engineering. GD & Spanish - the splashing is very much dependent on the mounting height of the unit AND the tub selected AND the location of the water column inside the tub. Mine hardly splashes at all. The ones I have seen that splash only do so for a minute or so until their is enough of a pool in the tub to counteract it. Flat bottom tubs with tall ceilings are going to splash more than one from 7' into a sloped contact point in the tub. Besides , we're talking water in a bathroom, generally tiled so what's the big deal ??? It's not like the amount of splash is the same as taking a shower and leaving the door open. 2. While you are correct in that "the water cools off much more than it would from just a regular tub filler", it's not as if it cools off enough for anyone without a thermometer to tell a difference, and a very sensitive one at that! Sure the air cools the water more from a stream falling from 8 feet than one falling from two feet. But bath water that is 100 + degrees is not going to cool down to 90 deg. in the xtra 1-2 seconds it takes it to fall from the ceiling- get real. Additionally , that filler produces a very dense column of water (laminar) that has little to no air in it, so one might argue it will be hotter and less prone to heat loss than a "regular" filler that introduces room temp air into it's stream - thus cooling it off on it's way to the tub. So don't worry Spanish -your tub will still be plenty hot with that filler if you choose it. IT'S A NON -ISSUE people. I've already alluded to the real issue for lower tub temps - FILL TIME. That's directly related to the delivery system ( valve). If your valve and accompanying filler will only deliver 5 gallons a minute it's going to take a while to fill an 80 gallon tub, and there will be some heat loss. Select a valve that delivers 20 gallons a minute and you can be soaking quicker that most people can undress. Here is a link that might be useful: laminar valve body - see page 2

#1 - GFI protection is OPTIONAL for this light. It is NOT mandatory NO required. I never GFI protect shower cans. There is no reason for it. #2 - TRIM that is rated for use over a shower. The can is the same either way. #3 - If the ceiling is up, as yours obviously is, you would use an "old work" can that just cuts into the sheetrock and is held up by clips. Using a new work can with the bars is useless and WAY more work than you want to know.

Thank you, I believe the room height is 10 feet but I will check on that. I definitely understand the safety about not having something above the tub (which is why we didn't have anything when we built) but I just feel like we need something over there. We have recessed lights but I was just looking to shake it up a bit!

Not a fan of that light fixture. Would not want to look at/into the light but rather have the fixture provide light for the room. If you want an interesting ceiling hung light, consider this LED one: https://www.beautifulhalo.com/6led-leaf-design-semi-flush-light-nordic-style-acrylic-ceiling-flush-mount-in-warmwhiteneutral-p-326243.html?currency1=USD&track=PA_G_SUS325&gclid=EAIaIQobChMI1IbvvfjH5QIVVdyGCh0DNgObEAQYASABEgI74fD_BwE You might consider a faux window light -- perhaps even a stained glass one: http://diphotoshop.com/3-tips-for-highlighting-the-exterior-architecture-of-your-home/ http://nanobolt.co/fake-window-light-box/ Or a fake window skylight light: The local hospital has one but I couldn't find a pic on line that would load. Are you aware that there are light fixtures made specifically for corners? I like this one best: http://kapemvun.info/foliage-not-flowers/ but there are others worth considering, too. http://kapemvun.info/easy-fix-for-fall-flowers-to-get-up-your-garden-2/ http://kapemvun.info/10-no-fail-drought-tolerant-perennials-for-low-water-gardens/