What do the cabinets on each side of it look like? I have a 3 drawer stack on one side of my trash pull out and a set of doors on the other. I chose a door panel with a drawer above it for mine and it looks great. I did not mount the handle in the center like you would for a drawer, I mounted it exactly like it is on the real doors....off to the side. A 3 or 4 drawer stack panel would have looked fine too. sorry for the dark picture...but the cabinet door on the far left is my trash pull-out.

I bought: a pull out trash for my trash/recyclables a sink tilt out tray A Lee Valley pull out pantry larder unit My cabinets are being installed now so I will wait to see how everything fits once I have moved back in. I might add a few more storage accessories. ie tray dividers, under sink pullout and ???? Good luck! Here is a link that might be useful: Larder unit

"...A $700 6" spice pullout is an expensive space filler that isn't that usable..." I beg to differ. I have two of them...and they're a lot more useful than empty filler! I fit a lot of items on them that would take up space in other locations and be blocking each other. With my filler pullouts I have my many, many baking sprinkles in one and my most used spices, ingredients (like molasses, honey, cocoa, vanilla), and recipe box in the other. The one w/the baking items is in my "Baking Center" and the one w/spices, etc. is in my Prep Zone - all very conveniently located and very useful! If you put the tallest items on the bottom shelf and the shortest (or most used) on the top shelf, you don't have to lean over that much or that often. Finally, they are too narrow to have items more than two deep, so that means you can pretty much see everything stored in them! My cabinets were already delivered so it was either filler pullouts or empty filler...we had to "fix" one of the many measuring errors by my KD. But, if I had to do it over again, I would try to fit at least one in my kitchen. (Just so you know, filler pullouts are available for both base and upper cabinets.) Oh, and they are not $700...mine were less than $450 each. $700 may be Rev-A-Shelf's "list" price, but not even my KD would charge that much for them! [In the interests of full disclosure, I did not pay for mine - I insisted my KD pay for them b/c I lost so much cabinet & pantry storage due to her measuring mistakes! But, they did try to charge me, so I have the change order they tried to get me to sign.] Together... Baking Center side (left of cooktop)... Prep Zone side (right of cooktop)... > Roll Out Tray Shelves (ROTS)...items can fall off ROTS b/c most have short sides. If they have high sides, then they may as well be drawers. Pot/pan/container handles and anything else that might hang off the sides of the shelves can get caught on the frame of your cabinet and ding it - both coming out and going in. And, of course, there's the issue I mentioned previously about being very careful you open the doors fully b/f pulling an ROTS out so you don't ding your cabinet doors; and being very careful about making sure your ROTS is completely closed before closing the doors so you don't ding the doors on the corners of the ROTS when closing the doors! Drawers should not be so deep that you have to stack different items on top of each other...plan your drawers accordingly - I have both 3-drawer and 4-drawer stacks - I planned my storage so other than a few drawers, I don't have to stack things. It's nice having my pots & pans in a drawer mostly one layer deep (pan + lid stored together) so I don't have to shift things around. [FYI...I think webbrowseraz is a spammer...the only posts I could find from him/her - all four (spanning from January to now) - link to the same site with basically the same post as on this thread.]

We had one made by the cabinet company that did my 2003 kitchen. They used a metal channel that they screwed into both sides of the cabinet. It was "u" shaped. Then they inserted the cutting board and slid it into the U channel. In the picture below, it looks like the cutting board is nicely held in place by the cabinet frame. It was not, since the board inside the cabinet was free to move up and down until the u-channel was placed there. An old boyfriend did something similar with an old 1950s TV cabinet with doors over the picture tube. Where the TV went, he made shelves for my stereo components. He used cove wood molding trim. With one side of the trim glued and screwed to the cabinet, the other flat side formed a little ledge to put the shelf on. By putting a second cove molding above the shelf, he made a full-length track for the shelf to slide into. Doing this in your cabinet would be a simple weekend job. The hardest part might be getting a cutting board the right size to fit into the cabinet, unless you have power tools and can make it yourself. Here is a link that might be useful: here is the pull-out cutting board in my old kitchen