I like the idea of using drapes and thanks for the pic @valinsv and I will probably be stealing your bay window look with the candles etc. it looks great. Our living room is tiny and I have noticed that since I removed the vertical blinds, the room feels so much bigger than before, which is why I wanted to go with something mounted inside the window. Do you guys think that using the drapes will make the room feel small again, or will using the inside mount blinds, make it even worse? The drapes across the window will certainly make my life a whole lot easier. Someone had also mentioned traverse rods which I had never heard of. I have looked into them, but I am not sure if it is a solution I would like since it seems as though I will have to use the little hooks on my blinds. Has anyone ever used them, and if so any thoughts? Thanks for the tip on the handles, I will look for them the next time I am at Lowes. Thanks!

I sewed grommet top panels together for my patio doors and it worked out just fine. I opened the right side vertical hem on one panel and the left side vertical hem on another and then sewed the two sections. I used a double stitched seam.This is a combination seam-and-edge finish that creates a narrow seam and prevents the fabric from raveling. First I stitched a plain seam. Then stitched again, 1/8" away, within the seam allowance, using a zigzag stitch. I trimmed the seam allowance close to the second row of stitching and then pressed the finished seam allowance to one side. "Easy peasy". It can be done with minimal sewing skills. The grommet spacing might be a little wider or narrower where the panels are joined but you don't see that at all when the curtains are open and its barely noticeable when the curtains are closed.

Timely topic! We live in a wooded area with lots of oaks and maples and stone walls and gardens. Consequently there are many chipmunks. They have nested in my car's cabin air filter and have even hung out in the cabin. Their scat resembles that of other small rodents, but the acorns in the nest is sort of a giveaway. I have cleaned the vehicle and replaced the air filter on more than one occasion. I recently did that, and the chipmunk/s is back again. I had saved a dead, dried out, cool, large benign insect (to photograph) in a small cup that I set in the center cup holder bin. It was very DEAD. A few days later when using my car, GONE! Mr. Chippy took it. So, once again I must go through the cleaning, sanitizing and replacement of the cabin air filter. Grrr. It goes without saying that rodent poop, like the scat of most wild animals, is nothing to mess around with. Rodents can harbor parasites and diseases. I spent a while perusing online for solutions to this common problem. I read about a lot of purported solutions, most of which are ineffective or problematic (dryer tissues, scents, gizmos and gadgets, and, heaven forbid, poisons -- NO!). There is no way to "exterminate" every chipmunk, even if I wanted to. Our home is in a conservation area, for one, and there are hundred of nut and seed producing trees. One year a small weasel showed up and had a talk with a lot of the chipmunks. Weasel was t seen this year. I am going to have to clean out the garage from inherited furniture, replace the rodent chewed garage door gasket, and keep the car or cars in the concrete bunker garage. Meanwhile, I will try to remember not to have any snacks, even food, taco wrappers in the car. No eating and no crumbs. No ketchup packets in the glove compartment. I will look into installing some wire mesh physical barrier around the air intake and the cabin air filter. Not as easy as it might sound. Here, below, is the only promising approach I can across online. It is from a viewer's comment on a YouTube video and I will include it here for the purpose of discussion. Seems like a lot of effort. (Note: anyone trying to install a mesh barrier wants to be sure that they don't end up choking off outside air supplie to their engine of something important.) ~~~~ The only way you can stop the mice from getting into the Cabin air filter in a Toyota Corolla is to place 1/4" square wire mesh (buy from Home Depot), in a small roll, ( its called "1/4 x 1/4 Welded Hardware Mesh" ) over the openings where the air goes into the car's cabin. I own a 2008 Corolla and I raised up the front hood, then removed the passenger side plastic cover that is at the base of the window, and that gave me access to the air intake holes. Guess what: Toyota made it all but impossible to actually get your hands into that space where the air intake is. They put another beam in front of the intake, about 1.5" in front of it. I cut 2 strips of mesh, each one 2.5" wide, (one set 5" long, another one 6.5" long), and I used 1/2' dia SUPER-MAGNETS to hold the wire mesh strips into place while I used 'Goop' glue (from Walmart) to glue those mesh strips securely into place. The magnets 'PUSH' the mesh onto the metal of the car itself, so the mesh has to be placed between the car and the magnets. I just left the magnets behind on the 2.5" wide mesh strips. For the 2 mesh strips on the left hole; I had to glue the magnets onto the strips first, then let the glue dry, and then push the strips in with the magnets securely fastened to the strips, because the magnet at the far end is so far into the body work of the car that its impossible to actually get your finger into that space to place the magnets once the screens are pushed into the proper place. As if this was not hard enough, Toyota placed a bar in the middle of the air intake hole, so you have to cut the screen covers into 2 halves, one half for the left hole (using 2 6.5" long strips) and one half for the right hole (using 2 5" long strips). Because the holes in the beam covering the air intake are only 2.5" high, that means the strips of mesh you insert cannot be more than 2.5" high. But what you REALLY need is a screen 4.5" high, the only problem is you cannot actually get a screen that wide into that space because the holes in the beam in front of the intake are smaller in size, that's why you have to insert 2 strips of screen, each 2.5" high. Yes, Toyota has really fu*ked up big time with this design ! First you place one 2.5" mesh strip over the hole, so it covers the lower half of the air intake hole. Then you take the second 2.5" mesh strip and place it over the hole, raising it upwards so it covers the upper half of the air intake hole. When you push it up it is pushed up and almost out of sight, so you have to do everything by feel, and using a small mirror to see what's happening. Doing all of this is an all-day job. But once you are finished there is no way in Hell any mouse is going to get through that wire mesh. The problem is that there are so many OTHER places around the car for those mice to build nests in, so just covering up the access to the ventilation system will just push them to build a nest somewhere else instead. But at least the insides of your car won't smell bad anymore. ---- Was a comment on the video below. https://m.youtube.com/watch?v=O9JruyHm89g

If you have problems with an iphone, you can go on line and learn a lot from their tutorials. For me to use it just for web browsing it is not a big deal. If you buy a $ 900.00 unit, it is overkill for the purpose of doing basic stuff, there are cheaper ways . I use an old desktop with window 7 pro and a couple of programs for uses like Gardenweb and other progams, got a nice 24" screen to go along with. When friends show nice pictures of their efforts it show up nice with my set-up. For me it does your pictures no justice to watch it on a dinky screen, Forgive me for being such a lousy pita.