Hi Alicia, I notice a lot of folks new to the forum accidentally miss the instructions, or else maybe use the wrong search box and it yields responses from all the GW forums. By now you've seen that I posted the instructions to the threads you started, and gave a link to the original review thread. I then went and copied your nice reviews to the original threads for those members. No biggie. It happens a lot. The main thing is that you took the time and effort to write nice reviews for the many nice trades you've had. The only down side is that there are limited pages here so those individual threads cause reviews on the last page to drop off. Again, it is not a very big deal because if a member has not had a review in over 2 years the chances are they are no longer trading and might not be back. I sometimes incorporate reviews from the back pages that will be dropping off and copy them to another thread that is father away from the back page. May all your trades be as nice in the future. Oh,,,btw...whenever you 'do' happen to start a new review thread here for a member, you might want to NOT check the box to have the follow-up replies emailed to you. You could be getting lots and lots of reviews emailed to you for years to come. Happy Trading! Sue

I just updated Thunderbird to 15.0 cause I didn't have a send button.. I know I had one.. well I still don't with 15.0 & my pictures are still broken. My son wants me to get opera mail (he uses Firefox browser) but I didn't want it.. maybe now I do. I rebooted too as that usually helps solve a lot of problems. Am I missing it or is there a way to get it. I checked options & don't see anything. BTW I sent my letter using the send under file. Dar

http://energy.gov/energysaver/articles/heat-pump-water-heaters Heat pump water heaters require installation in locations that remain in the 40��90�F (4.4��32.2�C) range year-round and provide at least 1,000 cubic feet (28.3 cubic meters) of air space around the water heater. Cool exhaust air can be exhausted to the room or outdoors. Install them in a space with excess heat, such as a furnace room. Heat pump water heaters will not operate efficiently in a cold space. They tend to cool the spaces they are in. You can also install an air-source heat pump system that combines heating, cooling, and water heating. These combination systems pull their heat indoors from the outdoor air in the winter and from the indoor air in the summer. Because they remove heat from the air, any type of air-source heat pump system works more efficiently in a warm climate. ________________________________________________________ this is what I ment, that there is a cooled air discharge 6,000 btu in an hour so it may not feel as cool as it is...but it is there. where you notice or feel the difference is in the dehumidification this cool air provides. fan, evaporator,compressor..mini hvac system on top of water heater. just info saltidawg.

Sometimes on opening, a few bits get missed and fouls opening the page. The error message may not fit the situation. Try again. It may make it the second time. Do try again before resorting to messing with your settings. Another problem source is the computer having difficulty acessing its RAM memeory. How long has it been since yoru memeory cards have been installed (on the mother board) and never disturbed? If it has been 2 years, that can cause trouble. These chips use low voltage and over time corrosion can cause less than good connections at the card connector. Sometimes, exercising this connector will wipe away the corrosion film and re-establish good connections. This is done by moving the memmeory card up and down a little in its connector. You do not have to completly remove the card. Open the lock-down levers at each end of the card. This raises the card a small amount. Push the card back in. Do this 2 to 3 times, and then push the card home and lock the levers. If this was the problem, you'll see improvement in your system operation. However, failing access to the memory bank should cause other problems as well. In the "control panel" open "System". Click the general tab (system panel) and see how much RAM memory is showing. It should match the total installed RAM memory. If you see less than the installed amount, then there is a memory access problem. Usually, if there is a problem on a memory strip, the entire card is ignored. For example, I have 2 GB of RAM using 2 cards. When a problem developed on one card, that entire card was ignored and the displayed memory fell to 1 GB. [Another reason for not completly removing a memory card is that these are very easily ruined by static discharges. A static discharge below the limit of your sense of feel to a free standing card is enough to blow memory locations.]