@Shelley Graham Hi Shelley, it's been a long time since the original thread. On the off chance you see this, have you had any issues with the 4" in front of your sink? We also put in the larger Devonshire in our newly remodeled master bathroom. The stone fabricator left 4" in front of the sink. It feels like a bit of a reach to get to the faucet (we are using Devonshire single faucet.) I guess it also depends on your height? I'd love to hear your insights since you've lived with it for a while. Thanks much!

Funny that you guys started to discuss this just when I am about to start this same project myself. Here are my findings. First off, if you plan of putting a counter on top of the new 3.8 cu ft FL, good luck, and have your pocket book ready. You see, the deepest "standard" counters are those for kitchens, at 25 1/8". Assuming that one leaves around 5" of clearance behind those newer FL machines for vents, air circulation, heat, etc, then you are looking at about 30"-35" of depth, depending on how flush you want the counter to come to the front of the machine. Having said that, there are 3 prices for laminate counters in the stores (like Home Depot). The counters you see in the store in stock are the cheapest, and will cost around $10 li ft. If you need to pick a finish that matches say the sink counter top in your bathroom where the machines are also located, then that is considered a custom order, even if it is a standard depth. This will easily double the price to $20 li ft. Now if you want to order a non-standard depth so that it goes from the back of the wall to the front of your new FL, then you are looking at $35-$50 li ft, depending on type of finish like rounded vs sqaure front edge, back ledge or no ledge, etc... Keep this in mind when shopping for a counter top. I would like my counter to cover the machines completely, so I might have to bite the bullet and order the more expensive counter top.... Again, I am talking about a laminate counter top, no fancy materials here.... I am from Canada, and here is what the local Home Depot quoted me in Canadian dollars for the 3 options.. 1) In-Store counter (limited finishes) 25 1/8" (standard depth) X 6 feet = $68 CAD Custom order counter (you choose the finish) 25 1/8" (standard depth) X 6 feet = $132 - $150 CAD 30 Csutom order counter (you choose the finish) 30-35" (non standard depth) X 6 feet = $222 CAD I believe the last option of non-standard depth only allows for a square front edge finish. If you want a rounder edge in front, like that found on your kitchen counter, the price jumps to $500 CAD, since the guy said that they have to charge for a full 4X8 sheet, and then cut the custom size from there, in order to get the rounded front edge... One other option you can do, which my brother did very nicely is lay down 2 sheets of plywood (for extra thickness), and tile the top and sides, looks really nice, but is a lot more work...

These are my pics of my countertops placed Friday June 22, 2018. I cried looking at these seams. It looks so cheap. Fabricator explains that's the way it comes. I explained that I shouldn't be able to see the seams so clearly. It looks so unprofessional. They ended up taking them back to their warehouse. In hopes they say if it is quality control will try and fix it just to make it look better. Otherwise I will have to pay an additional fee for them to come out again to install. I just don't know what to do and if still looks the same. This is the first time I've replaced my counters in 24 years. I don't and can't live with it. looking at this for another 24 years. It looks so cheap and it really was not it's a lot of money to me. I hope fingers crossed that they will fix this problem. They never told me that there would be such seams. I thought the edges were done by a machine and it would be all one piece. I have read up on this and now understand there are seams. But now I do know that they should not look like this. If they are good fabricator you shouldn't be able to see them so clearly. I will find out next week what happens.

Breeze: This is a Lavanto I installed a while back. The "ledge" in front of the faucet deck is matched by the one you can't see in the front. I installed it with a slight positive reveal on the sides because that is the most practical, most sanitary, least maintenance, and best looking method. Surprisingly, I had to recut the rabbet in the cutting board that came with the sink; it was too small. The sink it replaced: