Interesting response. I didn't think about the burst pipes thing. Thanks for heads up. I didn't think it would get that cold though. I thought it may get down to 50 max outside. Should've checked the forecast anyways though. I don't know what he did, but the heat started working properly after he left. It hadn't gotten over 65 according to the thermostat since I turned the heat up Sunday afternoon. Once he left the temp quickly rose to 75 where I wanted it. I should've known better to inspect the parts he was doing but at that point I was so cold and didn't want to look at what he was doing. He was on his hands and knees in the snow outside. I guess I will wait and see if the blower motor dies. I only started paying attention to the noise so I don't know if it's making a weird noise. Expensive lesson I guess. You're saying the p/n is not for the blower motor? I searched for the part it's giving me blower motors, but with extra letters/numbers. That is kind of odd since on the paperwork he also did put a gibberish serial number for my unit. It's like someone was just doing asdafadfhkaa across the keyboard. Worst case scenario how much am I looking at to replace the unit including labor? Are newer units more energy efficient as well?

Hello All, First my apologies for posting this question as a response to an existing thread. I just could not figure out how to start a new thread and no matter what I tried, I was going in circles. Anyhow, I hope this question is relevant to this thread and will appreciate any answers. First the facts: I had a 5 Ton Rheem heat pump installed in our home to replace an 18-year old Lennox heat pump (Model HP22-461-2P) of about 3 or 3.5 Ton capacity which ran its course of life. The Air Handler is installed in the Attic and the external unit is outside. I bought the unit brand new and had it installed by a licensed HVAC contractor. The model of Rheem Air Handler Installed inside the Attic is RHPL-HM6024JC. The model of Rheem Heat Pump (External unit) is RPRL-060JEC. They are purchased as a packaged unit from a Rheem wholesaler through the web and I confirmed through Rheem officials that the units are compatible with each other and the seller is licensed to sell them. These are installed by a local contractor with a Honeywell FocusPRO TH6000 series thermostat which he, the contractor supplied on his own as per the agreement we signed.. The heat pump is advertised as 2-stage. Now, the problem: From the time it is installed on January 26, 2012, the outside fan is not blowing. I asked the contractor about it, and he seemed not sure, but told me not to worry about it and that it will come on when necessary. Then I read a little bit about heat pumps and also recalled that in the case of the earlier heat pump, the outside blower was running much of the time. Toward the end of its life (i.e., just before the installation of the new unit, however, the outside unit had ice formed all over it, and the fan was still struggling to run. A few contractors who came to look at it to give an estimate said that the old unit pretty much ran its life and that it needed to be replaced. One of them said with so much ice outside the heat pump is doing nothing but wasting electricity and disconnected the outside unit from the socket and asked us to put the inside thermostat to emergency heat because that is how we were getting the heat anyhow. This was the condition at the time of the new installation. The new contractor of course, threw out the old outside unit as well as the in-the-attic air handler and and replaced them with the new Rheem units and installed the Honeywell thermostat FocusPRO TH6000. Since the installation, I kept observing the outside unit and found that it was never running. I contacted the contractor after a couple of days and he said we could test it by turning off the circuit breaker for the outside unit off and wait for 5 minutes and then turn it on to see if it would come. When we did that, the outside unit fan did come on, but within a minute or two after picking up speed, it shut itself off. The home is getting heated, but I am concerned that the unit is running as an electric heater rather than as a heat pump because the outside fan is not running at all. This seems extremely unusual. I wrote to the supplier and he says the problem is most likely caused by wrong installation or wrong wiring. When I asked the contractor about it, he adamantly maintains that there is Zero Wrong with his wiring, but he does not have an explanation as to why the outside fan is not blowing. I wrote to the supplier again, and he says that in the most unlikely event that something is wrong with any of their components, they will replace them under warranty if I get a written estimate and a confirmation of the problem. My guess is that the contractor made some error in the wiring, perhaps a simple one, but am not sure what it is. According to the Owner's manual I downloaded, the Rheem heat pump is with serial communicating technology and it consists of Indoor Air handler, Outdoor air conditioning condensing unit/heat pump, and a touchscreen thermostat. The touchscreen thermostat is not supplied along with the heat pump and air handler. I asked the supplier about communicating technology and he responded that they could supply it for about $400 extra. They confirmed that "The heat pump system is definitely equipped with Rheem's Comfort Control System Serial Communicating Technology. Looking at the specs document you can see that the heat pump is equipped with this technology. The air handler you bought RHPLHM6024JC is also Communicating. This system was designed as a matched Communicating system. In order to achieve the benefits of the Communicating system you will need a Rheem 500 series thermostat. The thermostat is not included in in what you purchased. To keep prices low we sell matched split systems and let customers choose their own thermostats." I would like to know: a) How we can diagnose the reasons for the outside fan not running b) Whether the outside fan is supposed to spin when the unit is on Heat and the temperature is cold outside. c) How we can fix it to ensure that the unit is functioning as a heat pump d) Whether it is advisable to consider purchasing the thermostat recommended by Rheem have it installed. Thank you for any info or guidance you can provide.

I looked at the manual, and I interpret the diagram you mentioned as how to convert an existing two stage cooling that uses a PSC motor to the Evergreen two stage cool. The diagram shows how to wire the high voltage, but not the control voltage. I think they assume you already have the control wires in the harness coming from your furnace control board for two cooling stages. Those control wires would have gone to fan relays in the PSC setup. Is this a DIY project, or are you going to get a contractor familiar with the Evergreen to do the conversion? If this is DIY, I can point you to a website that answers DIY and there may be someone who has done what you want to do, If contractor, make sure he knows not only how to convert from PSC to ECM, but from one stage cooling to two stage. In general, it seems like the Evergreen can be used for multi speed applications, so the pieces are there. It just will take some knowledge of how to make it work.

I installed a spark tester, which installs between the spark plug wire and the plug itself. There's a small bulb that lights when you pull the cord. I verified the tester works correctly on my Echo trimmer. I also removed my coil and tested it with an ohm meter. It read within spec for the coil, assuming my information was correct about the spec. However, this morning I read on this forum that someone said a resistance test using multi meter is inadequate for newer coils that have ignition circuits embedded into the coil. I need to rule out the kill switch, but thinking that there is no other option other than the coil. The fact that the coil is 1/3 the cost of the blower really stinks.