Another granite question -- best edge?
harriethomeowner
15 years ago
Featured Answer
Sort by:Oldest
Comments (15)
mainecoonkitty
15 years agoharriethomeowner
15 years agoRelated Discussions
Please help-what is best option with bullnose at tub/cabinet edge
Comments (7)Thanks you guys for your input. I won't be doing anything to the cabinet. The cabinet builder had done the work and I don't want to fuss with it now:) The original building plan was for the tile to be recessed into the side, butting up to the frame. But I built out the cabinet wall more fully than the initial plan. The plumber thought I needed to do the build out to correctly get the tub's tile flange covered. The hardy backer was originally going to set on top of the flange but the plumber would like to see it over lap the flange. So that is what I did. Hence the tiling surface is now too shallow to go with the the original plan. I had thought of the skinny tiles all the way down the frame but I don't like the look when I mock it up. I liked option #1 because it was efficiant in its design and has a clean look. But I worry about maintainance. If I do #1 I was planning on caulking the gap before tiling, painting with Hydroban, tile as usual, than caulk the seam between the wood and the tile. Any more thoughts on these ideas?...See MoreSticker shock . . . another cost of granite question
Comments (19)Also - forgot to mention, take a look at the videos on BC Stone's site - quite informational. I know many folks here swear that you should be there when they template, you should be there when they lay it out on the slab and decide upon seams, etc. I must confess I didn't do any of that and an extremely pleased with the results. I asked our contractor about it and he had me talk to BC Stone directly. They said I was more than welcome to but explained their process. Templating is done with electronic / laser measurements - not luan like most use. Seams and layout - they would do cut outs if I wanted to drive the 2 hours to see it but they assured me if I told them if there were any parts of the slabs I wanted to feature / stay away from they would work around it and do a seam that wouldn't be noticeable. Well given that I chose them based on their reputation, I went with their judgement and decided to let the professionals do their thing. I am very glad I did. the one seam we have is hardly noticeable. When I first looked at the install, I walked past it twice before I said, oh, there is the seam. If I had laid it out, I would have done a worse job of locating the seam. And their templating was spot on. Everything fit like a glove. No gaps, flush to the wall (which weren't necessarily straight), tight fit. They had to do no on-site modifications / drilling / etc - everything was cut perfectly back at their facility So if you hire a professional and feel comofrtable with them, let them do their thing. No need to micromanage their work...See Moregranite edge to beginning of undermount sink
Comments (28)First I would like to thank you for the time you have taken to draw up the schematic. As you can see from my first photo there is a white marker line towards the back of the sink. You can see how much of the back flange had to be cut away. Take notice of my faucet how I had to put part of that flange back up there to get my faucet to stand true. Also notice where they put their brackets in reference to where the sink outline is. The brackets are on the inside perimeter of the sink. My biggest concern is the structural integrity of the sink. The manufacturer of the sink will not warranty it so if the sink was to fail I would have to get another sink to fit the same opening and also modify it to fit. Which again will affect the structural integrity of the sink according to the manufacturer. My biggest concern is that there was plenty of room to install the sink without modifications had the hole been correct. There are six brackets holding the sink in place two on each side and two in the back corners nothing in front. We sent to sink & template to the fabricator and still it wasn’t correct....See MoreAnother granite question -- regarding chipping
Comments (18)According to granite fabricator, he said they will come back and do a walk through with us and fix everything once everything is installed. Yes there is a GC. I think this might be the 1st time he has used this guy. He chose him, not us and no I did not see anything written. We live in a major city so yes there are factory fabricators. I don't know enough about construction and apparently am too trusting of my GC. Now I am realizing many more things that were not done correct according to what I am reading. Mainly, plywood was NOT put on top of my cabinets prior to granite going on and the sinks (all sinks in the whole house) are only being held with epoxy, no clips, no plywood "sandwich" nothing. Just sick about this whole situation!...See Moremuscat
15 years agoUser
15 years agoella_socal
15 years agoazstoneconsulting
15 years agokatiee511
15 years agocharlikin
15 years agoerikanh
15 years agoUser
15 years agoastridh
15 years agojen19083
15 years agoalaskangirl
15 years agohld722
15 years ago
Related Stories
REMODELING GUIDES9 Hard Questions to Ask When Shopping for Stone
Learn all about stone sizes, cracks, color issues and more so problems don't chip away at your design happiness later
Full StoryKITCHEN DESIGN9 Questions to Ask When Planning a Kitchen Pantry
Avoid blunders and get the storage space and layout you need by asking these questions before you begin
Full StorySELLING YOUR HOUSE15 Questions to Ask When Interviewing a Real Estate Agent
Here’s what you should find out before selecting an agent to sell your home
Full StoryDOORS5 Questions to Ask Before Installing a Barn Door
Find out whether that barn door you love is the right solution for your space
Full StoryLIGHTING5 Questions to Ask for the Best Room Lighting
Get your overhead, task and accent lighting right for decorative beauty, less eyestrain and a focus exactly where you want
Full StoryREMODELING GUIDES13 Essential Questions to Ask Yourself Before Tackling a Renovation
No one knows you better than yourself, so to get the remodel you truly want, consider these questions first
Full StoryMOST POPULAR8 Questions to Ask Yourself Before Meeting With Your Designer
Thinking in advance about how you use your space will get your first design consultation off to its best start
Full StoryGREEN BUILDINGConsidering Concrete Floors? 3 Green-Minded Questions to Ask
Learn what’s in your concrete and about sustainability to make a healthy choice for your home and the earth
Full StoryFEEL-GOOD HOMEThe Question That Can Make You Love Your Home More
Change your relationship with your house for the better by focusing on the answer to something designers often ask
Full StoryEXTERIORSCurb Appeal Feeling a Little Off? Some Questions to Consider
Color, scale, proportion, trim ... 14 things to think about if your exterior is bugging you
Full Story
kitchendetective