This old thread got revisited. @dani_m08 to answer the question about extra probe, I believe I ordered an extra one when I bought the set up. The probe wire is just setting in the junction box I think but honestly I cant remember. When I laid out the underfloor heating and the probe, I just ran another probe near the first probe, and it was then sealed into the floor self leveling compound as per instructions. then the end was just threaded into the wall like the one that would be live, and not connected, but just laying there in the box. Regarding the tile layout. I just decided to run it this way, after getting instructions on the 90Degree way, IIRC. The herringbone that I love is from my childhood and the side walks in my neighborhood that all ran at 45Degree. so that to me is herringbone. I know you posted on @sochi thread about her amazing bathroom and a wall mounted faucet. I would totally do it if I had the right sink for it. In my case I had made my sink out of soapstone and an integrated backsplash. The pictures of this bathroom reveal are no longer available because of the use of photo bucket, when it was Gardenweb. I did not keep my account with photo bucket. I'll add some of the reveal pictures so you can see the sink and floor. Regarding the sink there is no ledge for water to drip from my hands when using the faucet. The water drips right into the sink. In my other bathroom with a deck mounted faucet I am always wiping up drips and it is a nuisance. I much prefer the setup for this sink. Below: I love the flush finish from the faucet to the bottom of the sink. nothing drips on a counter or edge of a sink. Below: looking in from the doorway. Below: Here I am finishing up the sink. the backsplash was epoxied on as a separate piece. The whole soapstone install in the room took next to nothing to buy as they were all small pieces that I epoxied together with a 3 part stone epoxy. Below: this is the counter at the tub, and is in 2 long pieces but I was able to epoxy them together at there edges to make a wide slab for the top. All the soapstone was finished with a 60 grit sandpaper to be rough and this lovely soft tone of blue/green/gray/white. I did not oil it so this color tone would remain light. Below: If I recall correctly @sochi helped me decide on this Hubberton Forge Mirror. I have 3 different metals in this room, but they are all a cool silver to black color. Below: the center of this tower shares space with the kitchen on the other side of the wall. there is also some extra space that houses some electrical wiring. this is an old simple house. this bathroom was an add on when it got move to the farm in the 30s IIRC. The plumbing was all rearrange and some of the details that were orignially there I kept but updated it, such as this tower feature. The old one went and the carpenter did a wonderful job with this one. Below: This feature was another thing I kept from the old bathroom but flipped it from the other end and had the carpenter put drawers in it. Before it was a hell hole. things got lost and the build was soooo old and creapy I didn't like using it for storage. Now it is perfect for storage.

Thanks, greg_2015, you explained that better than I would have. Lucija, what you did doesn't hurt and may have helped if the problem was a blockage or just something nasty in the drain (you can also use a plunger to clear out), but the fact that it keeps happening suggests that the trap/venting combination is not working to keep water in the trap and block sewer gas - so probably the main advantage of what you did was just adding water. As a short-term fix and to diagnose, putting regular water in just refills the trap and blocks the sewer gas from coming up - a few large glasses should be enough. Then once you know that, you'll be able to discuss with plumber what needs done. Maybe a better trap, maybe it's only caused by your own toilet flush suctioning water out (and some 'local' solution might be possible), or maybe it's an issue through the whole building. It couldn't hurt to ask your neighbours (especially above and below you because it's probably the same vent) if they have this problem too. Or maybe they know a better plumber. )) I have a shower that has a similar issue and it's obvious that running the shower for a few seconds after flushing the toilet stops the sewer gas issue - the toilet flush suctions water out of the trap. Will get the plumber on a better solution sometime soon.

Right?! I love it so much! Right now I am using just white with it, but I think I will throw some bright coral colors in there too.

@Amir Ali - I just wanted to post a comment in order to: 1. Let you know that I completely understand what you are going through right now. I have TWO FAILING slate floors that are part of current bathroom renovations. The master bathroom floor had not been grouted due to delays on his part. I discovered that some of the tiles were COMPLETELY LOOSE - and some sounded like they were only partially bonded to the floor. This floor is failing - and it has BARELY been walked on because the bathroom renovation basically stopped due to issues - bathroom isn’t usable so the only use has been when I’ve gone in there to take photos or measure something = maybe some tiles had been walked on four or five times before I started discovering the loose tiles. It is obvious that the tiles failed to bond to the floor - the mortar must have skinned over or something. I am NOT reinstalling the loose tiles. IMPORTANT - my former contractor does not fit the definition of what people here on Houzz love to refer to as a “hack” (at least not the actual business that I hired to do the work) - however, his employee clearly did not know what he was doing (or just didn’t care) - and that makes the owner of the business liable for this work. The business has hundreds of Google ratings (4.9/5), owner is a member of TCNA, I had several reviews from people I know (and trust), and I DID NOT JUST TAKE THE LOWEST BID - I am NOT a CHEAPSKATE. I am so tired of people AUTOMATICALLY blaming the homeowner when they have ZERO basis to do so. Making assumptions and basically telling homeowners that they are IDIOTS and CHEAP really makes me upset. Okay, I’m finished with my rant! 😂 The ”fix” is this: The ENTIRE floor is being torn apart. Not only is the tile being removed, the cbu will be taken out. New contractor assumes that he will also find that former contractor failed to add the required second layer of plywood in order to make sure that the substrate was prepared correctly in order to have a natural stone floor installed. Based upon the above issues, I investigated the slate floor that was installed in one of the other bathrooms back in April. I noticed a few grout issues - and as I went around knocking on each tile, the sound on many tiles indicates tiles that are only partially bonded. This is what the floor looks like from a standing position: And this is what it looks like when I realized that I needed to inspect it after the failure in other bathroom: I have cracks and broken spots of grout in many places. I also have some grout which is stuck on my tile because the contractor failed to seal the tile (as required) prior to grouting (I found this out later - I was in the hospital while this floor was being installed) and made promises over and over to come remedy the issue. So, this floor will also be ”fixed” in the same manner as the first one - I’m just waiting to have it ripped out until after the other bathroom is completely finished. 2. I also wanted to let you know that regardless of whether (i) you have a written contract, and (ii) that contracts specifically provides (or fails to provide) a five year (or however long) warranty period, you still have recourse against the contractor who installed your tile. Most states (probably all but I haven’t done research on this issue in every state) have enacted statutes that protect homeowners for this type of issue. In my jurisdiction, there are specific statutes that relate to home renovation projects - these statues require (among other things) that all work must be done in a good and workmanlike manner. Following industry standards, as well as manufacturer’s specifications, are part of this requirement. Also, the consumer protection act in my state also protects homeowners against contractors who perform shoddy work. I am 99% positive that your state will have some similar statutes. If you want to share your jurisdiction, I am happy to take a quick look in order to point you in the right direction. MANY jurisdictions require the homeowner to provide the contractor with notice and a right of remediation. Unless you follow the requirements of your particular statutes, you won’t be able to bring an action against your contractor to recover damages. FYI - my former contractor has chosen to ignore the notice I provided, so I then was free to hire another contractor to do the remediation work. My former contractor will owe me the money I have to spend to correct his failure to properly install my tile (which will greatly exceed what I paid him - removing tile + cbu + buying new material (including nice slate tile - because I didn’t purchase cheap slate tile for the the project initially). I am sorry that you’re going through this because it is NOT fun. I decided to consider myself “lucky” because he hadn’t yet installed this tile on my laundry floor! Hopefully, you won’t have water damage that will require even more remedial work in order to fix it.