I ordered undercabinet fluorescent lights from CSN Lighting last July, and had a couple of problems with the order. First their website listed one price for the units, but when I select the items and proceded to the checkout, a different (and of course higher) price was used for calculating the total. Then, when I called to get the price problem straightened out, I specifically asked whether fluorescent tubes were included with the lights since the website said (and still to this day says) "This undercabinet fluorescent light bar is the latest in undercabinet lighting, complete with energy efficient T5 fluorescent lamps." which really suggests that the lamps would be included. Whereas the PDF specifications file from the lamp manufacturer noted that the lamps were not included. So, the person I talked to checked and said that the fluorescent tubes would be included with the lamps. When the shipment arrived, no fluorescent tubes. After several subsequent calls to them I was unable to get the matter straightened out, so I ordered the tubes from elsewhere and have decided to not give any more business to CSN Lighting (or any of the dozens of other CSN stores) My main lighting for the room, I ordered monorail track lighting from Arcadian lighting, and had a much better online shopping experience. They honored their 110% price match guarantee without batting an eyelash, and the person I dealt with there (Tony Lin) was extremely helpful. The order was shipped with two incorrect items, and Tony noticed it before the package arrived, and immediately shipped a separate package with the right items, and a prepaid shipping label to return the wrong items.

Please check on Thermador customer service reviews. I contacted them several times trying to figure out which part numbers I'd need for an ng to lp conversion and was not pleased with their customer service, at all. That's been a few years ago, so it's possible things have changed.

And I'd like to add one other thing to my overall question. So the entire knob and tube run is pristine. Very good condition, very nice Everywhere I can see it running (through part of the ceiling joist cavity in an open frame construction). I'm just going to leave it alone because I can't get new Romex up there. But our kitchen is attached to the backside of our foursquare house and as a result there is actually an extension off of the home that extends the kitchen out a little bit further. It was original and since it was original there's no insulation in the ceiling. The lighting fixture as well as the entire three-way switch loop is all completely in open uninsulated cavities which are compliant even according to the latest NEC. However we would like to be able to put insulation into the other section where there is just a hip roof above the ceiling. When the ceiling is up there will be no access which I know is a parameter in the code. I know that you cannot run knob and tube around insulation or have insulation over it even though in some states apparently there is a waiver. So I'd like to try to figure out a workaround again since I cannot rewire the connections to the fixture with romex what choice do I have? Is it possible to at minimum install conduit above the insulation with a new single neutral wire that connects to the knob and tube in two places? In other words just replace one section of the existing run so that it is protected from insulation that we would want to put up there? Optimally I would relocate the neutral and shorten its length, but cannot do that due to the restrictions of splicing in romex. There will be no other loads on the neutral because I will be re-wiring all of the others with new Romax from the basement. It's only this one stupid lighting load on this three-way switch. Thanks for your guidance!

l wouldn't use black, but you should probably try it out. Go to Home Depot or whatever is near you and select hardware in as many different finishes as they offer (save the receipt!). Get some different kinds - long, short, chunky, sleek. Preview them in your kitchen and see If any add personality or tie things together. You may find something that rings your bell that you'd never really thought of. If you like a particular finish or style, but not necessarily the one from that store, you can look at similar things online or in a specialty hardware store after you get things narrowed down. Be sure to save everything and take back what doesn't work. If you happen to live near San Diego, make a trip to San Diego Hardware. It's fabulous! but you can't take home samples to try. You have to know more or less what you're looking for. Other places may have similar stores?