Check Engine Lighet AGAIN

15 years ago

Sorry for the capitals, just trying to scream my dissatisfaction with my low mileage 2005 Chevy Colorado, with the big 4 cylinder engine and manual transmission.

The truck was purchased new, and has seen only light duty, about 13,000 miles on it to date. The biggest load it has had is a yard of mulch and a light aluminum fishing boat in tow for short distances and that no more than 10 times a year for both.

Anyway the check engine light came on shortly after the 36 month point and when I paid the dealer to check it, it got a new oxygen sensor. I forget the cost but well over $100.

The light came on again today, and I thought wouldn't it be nice to have a code reader - e.g., the Action CP9410 on Amazon for $55, with over 100 customer reader reports on file.

Does the owner manual for the Chevy tell me where the code reader plugs in? I assume it is something "hanging" under the dash, or on the engine side of the firewall.

In spite of the good advice from "johng", I'm a committed shade tree everything (mechanic, electrician, plumber, painter, cabinet maker) so why not at least have a "shot" at the problem with a code reader. The truck is running normally with the light on (has been on for about 5 miles, and came on while I was doing an unusually rapid acceleration trying to fit into a stream of 45 mph traffic passing by the store drive I was waiting in). I don't know if the push acceleration set something off that will pass, but I did check and reset the oil change function. The light remains on.

Sort by:Oldest

Comments (6)

bob_k
15 years ago
Jerry, you can go to Auto Zone and they will read the codes for free. While you are there you can watch them plug in the code reader. That way you will know where the connection is.

Good Luck
Bob
jerry_nj
Original Author
15 years ago
Bob, thanks, there is an Auto Zone near me.
Related Discussions
Honda FG100 tiller w/ dirty GX31 engine & oil
Q
Comments (15)
I don't know about the rest of the tiller, but I do know something about the GX31. The Honda small engines can run at all position BUT it can't sit on the side or up side down!!!!! VERY IMPORTANT!!!. It has a oil chamber to whip the oil into mist so you can run in all position. But when the engine stop, oil is going to go to the lowest level due to gravity. If the engine sit side way or up side down, oil will sip through the rings and go into the combussion chamber. If you leave it sit long enough, the engine not only hard to start, also it will smoke for a while. But it will clear up. That is the reason the foam filter soak with oil. So do not just tear the engine up until you run more test. You might want to clean the carb. I just did one on my GX31 and is not that hard. But If you can start the engine, I don't think you even need to do that. Just wash the foam filter with soap and water, put oil and put it back. Change the gas filter and check the plug. You check the oil but putting the engine with cylinder upwards, on flat level. Remove the drain plug and make sure the oil just not overflow. Start and let it run for a little while, the smoke should clear up. Then you can continue testing whether it has power. I am not saying the engine has no problem, just say the smoking is normal if the engine sit in wrong position.
...See More
Problem Mantis Tiller w/Honda engine (long)
Q
Comments (4)
adkinska, no darn wonder and thank you for the obvious trouble you went to for me. That looks exactly like the schematic in my manual, and I was starting to think that, too, as it is the only way I could envision that looked like the schematic. No wonder I was confused. I don't think that's what the guy at the hardware store told me on the phone, and I watched them one time trying to fill and start it before making out a ticket. He definitely was doing it just tilting it to the side and pouring straight from the plastic container of oil. Wasn't getting anywhere with that, wouldn't start, said I got it all spilled onto the spark plug and other parts, and would have to be all cleaned out which was probably true. So to be doubly sure here, you are saying that I should tip the engine FORWARD like that (perfectly clear, just went and tried it) for BOTH filling and checking? They only had that one tiller, and I don't think they know a whole lot about it to be honest compared to the other one they sell. I will emblazon that magic number 2.7 oz in my brain and find something more exact to measure it with and fill very slowly. A baby bottle comes to mind, maybe my new measuring cup(s) has oz on it. In time, I should gain more confidence about that. What a difference a good explanation makes! First I will try what you said before bothering my son about it and hauling it back over there. You don't know how much I appreciate that! I will check if 10W 30 is the same as the SAE 30 they sold me that I've been using, knew not to put my snowblower/lawnmower oil in it from that older thread.
...See More
1997 VW Golf 2.0L Check Engine Light - Help!
Q
Comments (3)
dnt1, I almost went to a mechanic at a gas station down the street who said he would turn it off for $50. Then, I tried what you said after reading your post. And it worked! I drove first, not more than 10 miles, but the check engine light still remained on. Then, I cycled the key ign ON/OFF for 4 or 5 timems and the light turned off from the dash. What a relief for me! My teenage son's bigger concern was the stereo system not working, not the check engine light(obviously!). So, I called the seller and asked if he's got it, thinking that he might have replaced the car battery and must have had the radio code. And he did! He gave me 4-digit code and the procedure (wondered why he didn't give that to me when he sold the car...). So, everything is fine now and the car runs great. Thanks! ps. Hope other people with the same problem also would benefit from this post - like I did.
...See More
Problem with face-checking in engineered hardwood
Q
Comments (12)
And I was trying to be so careful how I worded that :). Hickory is fine to use. NOFMA has a well written article on selecting a species that I will link to below. Checking is not a common problem one will run into everyday. It is where the wood drys out too much and starts to split in the top face (wear) layer of an engineered wood. Inside environments should be maintained at above 30% RH. Some parts of the country the inside RH will drop down to the teens or single digits during the heating season. That is where dry cupping or checking can occur. If you are partial to an exotic wood, most will work if they are manufactured correctly, installed correctly and maintained correctly. When i asked about non-vented gas logs, they can be problematic too because they emit huge amounts of moisture into the inside environment. If a house is too tight you can get condensation forming on colder flat surfaces. That can cause the wood to gain too much moisture, then when it drys out it can and will check. Too high of an RH level is just as bad as too low. Not every single home built in the US is a prime candidate for a wood floor. The manufacturers recognize that and throw the responsibility of maintaining the RH levels on the end user. Fair or not, that's the way the current system works. Here is a link that might be useful: NOFMA species selection
...See More
jerry_nj
Original Author
15 years ago
Auto Zone does indeed provide a readout for the "check engine" light. I stopped by there and a nice young lady, couldn't have been more than 5' tall, just right for reaching up under the dashboard without a lot of bending over. She found the connector without delay and when I said boy you knew right were to look, she said most of them are in the same place. So, I now know where the connector is, and I could feel it with my hand when I got back behind the wheel.

Interesting too, for Chevy owners, on the way to Auto Zone I again had to do a hard acceleration (no wheel spinning even on wet pavement) and soon noticed that the multifunction display, above the Odometer/trip, the words "Fuel Cap" was displayed. First chance, I pulled off the road and checked the fuel cap. It felt loose, so I took it off and put it back. It is a flaky cap in my view, one can put the cap in and turn it to the "click" position and still the cap isn't on. I think that might be what happened and the acceleration shook it loose. Anyway, the AZ person said the code was for fuel system ventilation (I don't recall now exactly what she said). We looked and they had a replacement cap, but I said I'll check the cap I have out more before replacing it. She said the check light would not go out for a "while".. maybe until I refuel or just drive "far enough". The check symbol is still lighted, but the display no longer indicates "Fuel Cap"
bob_k
15 years ago
Jerry, check the rubber seal inside the cap and make sure there are no crack or small pieces missing. If it looks good put a little vaseline on the seal and put it back on. make sure it clicks several times. If that was the problem the light should go out after a few drive cycles.

Bob
jerry_nj
Original Author
15 years ago
Bob,
Thanks, the seal looked good, I can also try some Vaseline, suppose we have some here... the cap looked to my eye to be in good condition, I even looked for the tabs on the cap neck, as are present on the new cap I didn't buy. The tabs look undamaged, yet the cap has a strange start. I'll check again in the morning, but it seemed to me one could put the cap on and twist it until it clicked, yet it wasn't in correctly. For now the check engine light is on, but the display is silent on the "fuel cap" warning, so that may be a good sign. Seems strange that the on-board computer takes several operational cycles to reset, perhaps the specific problem is tested on a scheduled basis, and that schedule has not yet come up.
jerry_nj
Original Author
15 years ago
As forecasted by the the young lady at Auto Zone, if the cap is fixed the "check engine" light will go after a "while"... the sequence was today, about the 4th time I used the truck since reinstalling the fuel cap, I was driving with the "check engine" light on, then after being on the road for about 10 minutes the the readout displayed "fuel cap" - I pushed the display advance button and both the "check engine" and the "fuel cap" displays extinguished.

Check Engine Lighet AGAIN

Comments (6)

bob_k

jerry_nj
Original Author

Related Discussions

jerry_nj
Original Author

bob_k

jerry_nj
Original Author

jerry_nj
Original Author

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US

Check Engine Lighet AGAIN

Comments (6)

bob_k

jerry_njOriginal Author

Related Discussions

jerry_njOriginal Author

bob_k

jerry_njOriginal Author

jerry_njOriginal Author

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US

jerry_nj
Original Author

jerry_nj
Original Author

jerry_nj
Original Author

jerry_nj
Original Author